Transistors Q101 in PCB drive the laser diodes. When Q101 is shorted between their terminals, the laser diodes will radiate beam. If the top cover is removed with no disc loaded while such short-circuit is continued, the naked eyes may be exposed to the laser beam. DEH-4200SD/XNEW5...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-4200SD/XNEW5...
The time taken to turn to the deteriorated mode is at a minimum around 20 seconds while the time to return to the normal mode is maximum 40 seconds approximately. Make sure to check the sound quality in the normal operation mode. area and a heat sink becomes hot areas. Be careful not to burn yourself. DEH-4200SD/XNEW5...
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. DEH-4200SD/XNEW5...
WMA decoding format ..Ver. 7, 7.1, 8, 9, 10, 11 (2ch • The SD memory card is only available for audio) DEH-4200SD. (Windows Media Player) • Specifications and the design are subject to AAC decoding format...MPEG-4 AAC (iTunes en- modifications without notice. coded only) (.m4a) (Ver. 8.2 and earlier) DEH-4200SD/XNEW5...
While in the operating menu, press to control functions. CAUTION Use an optional Pioneer USB cable (CD-U51E) to connect the USB audio player/USB memory to the USB port. Since the USB audio player/USB memory is projected forward from the unit, it is dangerous to connect directly.
Page 10
The local seek tuning is on. TA (traffic announcement stand- by) function is on. A TP station is tuned in. The selected frequency is being (stereo) broadcasted in stereo. Folder repeat is on. (folder re- When repeat function is on, only peat) is displayed. DEH-4200SD/XNEW5...
See the table below for the items to be checked regarding audio: Item to be checked regarding audio Distortion Noise Volume too low Volume too high Volume fluctuating Sound interrupted DEH-4200SD/XNEW5...
3.2 PCB LOCATIONS CD Core Unit (S11 STD-DOUT) SD Unit (DEH-4200SD/XNEW5) Tuner Amp Unit Keyboard Unit Unit Number CWN4804(4200) Unit Number CWN4809(3200) Unit Name Tuner Amp Unit Unit Number CWN4812(4200) Unit Name Keyboard Unit Unit Number CWN4815(3200) Unit Name Keyboard Unit...
CD Mechanism Module 3.4 CLEANING Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-4200SD/XNEW5...
Page 18
FM/AM TUNER UNIT 10 9 8 18 19 5V → 3.3V EEPROM 5.0V AM ANT FMRF 3.3V 2.5V MIXER, IF AMP FM ANT DET, FM MPX, RDS DECODER FMRF RF adj ANT adj CF52 3.3V → 2.5V 2.5V 3.3V DEH-4200SD/XNEW5...
In case of the above signal, the communication Source keys with Grille microcomputer may fail. operative If the time interval is not 500 msec, the oscillator may be defective. Source ON SYSPW <- H Pin 46 Completes power-on operation. (After that, proceed to each source operation) DEH-4200SD/XNEW5...
• How to restore from each error is shown below. classification, shown below. 0x, 1x and 3x: ACC-OFF then ON, CD-OFF then ON, 0x: Servo-related errors Disc ejection 1x: Servo-related errors 5X: ACC-OFF then ON, Disc ejection, Disc reloading 3x: Servo-related errors 5x: Mechanism-related errors DEH-4200SD/XNEW5...
Usual product operation is implemented to outward appearances. Display update is stopped The screen gets still when entering this item. Every segment lights up Every segment including icons lights up. Every segment goes out Every segment including icons goes out. DEH-4200SD/XNEW5...
When the power is turned on/off the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows) DEH-4200SD/XNEW5...
Disconnect the connector. Remove the screw. Straighten the tabs at five locations indicated and then remove the Tuner Amp Unit. Straighten the tabs at three locations indicated and then remove the SD Unit (DEH-4200SD). SD Unit Tuner Amp Unit Fig.2 DEH-4200SD/XNEW5...
Page 25
3. Pull the seesaw button forward. 4.The seesaw button is disconnected from the grille. Note: When you want to assemble the seesaw button in the grille by contraries, take care not to break the hook. DEH-4200SD/XNEW5...
Page 26
Mechanism Unit from the table. Keeping the Mechanism Unit lifted by holding these tabs with your fingers may result in deformation. 3. Be careful NOT to hold the front part of the Upper Frame or the CRG Mechanism and NOT to insert foreign objects into these mechanisms. Doing so may result in deformation. Proper handling Improper handling DEH-4200SD/XNEW5...
Page 27
Note: Be aware that the colors of the lead wires do not match the indications on the Core Board Pattern (green wire to O and Fig. 1 white wire to P). Disc Detection Arm Fig. 2 DEH-4200SD/XNEW5...
Page 28
Clamp State (Driven by the Motor).” 2. Move the PU unit toward the outer track, by applying 1.5-V power to the CRG motor. Note: After moving the PU toward the outer track and taking the necessary measures, be sure to solder the lead wires. DEH-4200SD/XNEW5...
Page 29
After reassembling the PU Rack, insert the feed screw from side c in Fig. 5 (insertion depth: Approx. 18 mm for the part indicated in the photo). PU Rack PU Rack fixing screw Fig. 4 Fig. 1 18 mm Fig. 5 Fig. 2 Actuator block Fig. 3 Fig. 6 DEH-4200SD/XNEW5...
Page 30
1. Be sure to hold the PU at the positions shown in “Proper handling.” NEVER hold it as shown in “Improper handling.” Proper handling Improper handling Do not touch the object lens and ACT. Do not touch the VR. Do not touch the Hologram. Do not pull the FPC. DEH-4200SD/XNEW5...
20 seconds while the time to return to due to mistaken eject operation, reset the product or the normal mode is maximum 40 seconds approximately. turn off and on the ACC to restore it. Make sure to check the sound quality in the normal operation mode. DEH-4200SD/XNEW5...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-4200SD/XNEW5...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 9.1 PACKING DEH-4200SD/XNEW5...
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". Large size SCH diagram E.VOL uCOM_BUS uCOM_BUS A : DEH-4200SD/XNEW5 FM:-20.00 dBs AM:-20.00 dBs B : DEH-3200UB/XNEW5 AUX: +2.20 dBs CD/USB/SD: +3.04 dBs POWER_BUS...
Page 43
1608 R823 No differentiation is made between chip resistors and discrete resistors. R801 2.2k R813 Symbol indicates a capacitor. 1608 R809 100k 100k Q822 LTC114EUB No differentiation is made between chip capacitors and discrete capacitors. NM : No Mount DEH-4200SD/XNEW5...
MOTOR DRIVER LOGIC TABLE PowVcc2 1u/10 VO1- VO4- LOAD PLAY (1608) (1608) VO1+ VO4+ CLCONT VO2- VO3- LOEJ SWITCHES: CD CORE UNIT VO2+ VO3+ CONT S901:HOME SWITCH..ON-OFF IC301 S903:DSCSNS SWITCH..ON-OFF BA5839FP S905:8EJ SWITCH....ON-OFF The underlined indicates the switch position. PGND DEH-4200SD/XNEW5...
Page 57
3.3V LRCK 10 GND R606 BCLK DATA 11 DATA NM (1608) DATA BCLK 12 BCLK LRCK 13 LRCK AAGND1 AAGND2 14 GND 15 PGND /WAIT 16 WAIT i h g PGND NO MOUNT PARTS (NM) Land for manual soldering DEH-4200SD/XNEW5...
1 V/div fRFAGC 500 mV/div 500 mV/div 500 mV/div 9TIN 500 mV/div Focus Search waveform Track Open waveform 100 Track Jump waveform (32 Track Jump x 3) Ref.: Ref.: Ref.: REFO REFO REFO Mode: Mode: Mode: TEST TEST TEST DEH-4200SD/XNEW5...
Page 60
12 cm CD Eject operation Ref.: Ref.: Ref.: REFO AGND Mode: Mode: Mode: Normal Normal Normal 500 μs/div fRFAGC 1 V/div 9TIN 1 V/div 1 V/div aFIN 1 V/div μ Black Dot (800 m) during play Ref.: REFO Mode: Normal DEH-4200SD/XNEW5...
IC 591 (A,102,23) IC 341S2162 D 751 (A,12,104) Diode HZU8R2(B1) IC 601 (A,128,96) IC(4200) PEG639A8 D 801 (A,116,14) Diode DZ2S068C (A,128,96) IC(3200) PEG641A8 D 802 (A,119,14) Diode DZ2S068C IC 651 (A,119,108) IC S-80827CNNB-B8M IC 901 (B,24,70) Regulator IC S-1132B33-U5 DEH-4200SD/XNEW5...
Page 72
R 533 (B,120,49) RS1/10SR101J R 167 (B,45,96) RS1/10SR333J R 168 (B,52,99) RS1/10SR471J R 534 (B,120,46) RS1/10SR101J R 169 (B,47,101) RS1/10SR121J R 535 (B,120,42) RS1/10SR101J R 181 (A,102,95) RS1/10SR0R0J R 544 (A,137,40) RS1/16SS472J R 191 (A,92,103) RS1/16SS821J R 547 (A,136,40) RS1/16SS0R0J DEH-4200SD/XNEW5...
Page 73
(A,60,92) CKSSYB104K10 R 712 (A,100,35) RS1/16SS151J C 152 (A,59,90) CKSSYB104K10 C 161 (A,35,104) Capacitor CEVW221M16 R 713 (A,100,34) RS1/16SS151J C 162 (A,42,107) CKSRYB105K16 R 714 (A,100,32) RS1/16SS221J C 163 (A,43,103) CKSSYB104K16 R 715 (A,119,31) RS1/16SS104J R 716 (A,101,32) RS1/16SS104J DEH-4200SD/XNEW5...
Page 74
CCSSCH120J50 C 433 (B,159,136) CKSQYB475K10 C 606 (A,117,95) CKSSYB104K10 C 501 (A,98,75) 10 uF CCG1192 C 608 (A,138,95) CKSSYB104K10 C 503 (A,102,73) 10 uF CCG1192 C 610 (A,118,101) CKSSYB104K10 C 504 (A,98,77) 10 uF CCG1192 C 651 (A,117,108) CKSRYB105K10 DEH-4200SD/XNEW5...
Page 75
(A,91,7) Push Switch CSG1155 CAPACITORS S 1876 (A,139,7) Push Switch CSG1155 S 1877 (A,21,34) Push Switch CSG1155 C 1801 (B,146,32) CKSRYB104K16 C 1802 (B,157,17) CKSRYB472K50 S 1878 (A,33,33) Push Switch CSG1155 C 1803 (B,145,13) CKSRYB472K50 S 1879 (A,95,7) Push Switch CSG1155 DEH-4200SD/XNEW5...
Page 76
(A,97,22) Connector CKS6036 JA 1801 (A,153,10) Jack YKN5006 C 1806 (B,108,20) CKSRYB105K6R3 OEL Module MXS4013 C 1808 (B,135,8) CKSRYB105K6R3 C 1901 (B,99,29) CKSRYB104K16 RESISTORS C 1902 (B,82,24) CKSRYB103K50 C 1921 (A,89,25) CKSRYB105K10 R 1804 (B,88,12) RS1/10SR222J R 1805 (B,90,17) RS1/10SR222J DEH-4200SD/XNEW5...
Page 77
Motor Unit(LOADING/CARRIAGE) CXC4026 R 294 (A,18,28) RS1/16SS471J R 296 (B,32,30) RS1/16SS0R0J R 299 (B,31,13) RS1/16SS0R0J R 305 (A,60,34) RS1/16SS183J R 306 (A,61,37) RS1/16SS183J R 307 (A,58,34) RS1/16SS183J R 308 (A,58,36) RS1/16SS183J R 701 (B,37,21) RS1/16SS101J R 702 (B,38,20) RS1/16SS101J DEH-4200SD/XNEW5...