(shorting-solder) by referring to "the DISASSEMBLY". 4. After replacing the pickup unit, be sure to check the grating. 5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by electrostatic induction. DEH-P690UB/XN/UC...
Page 3
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DEH-P690UB/XN/UC...
Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) 2.1 PACKING DEH-P690UB/XN/UC...
Page 9
Polyethylene Bag See Contrast table(2) Case Assy XXA7417 Carton See Contrast table(2) Protector CHP3375 (2) CONTRAST TABLE DEH-P690UB/XN/UC , DEH-P6900UB/XN/UC and DEH-P7950UB/XN/ES are constructed the same except for the following: Mark Description DEH-P690UB/XN/UC DEH-P6900UB/XN/UC DEH-P7950UB/XN/ES Cord Assy CDP1041 Not used...
Page 11
Holder XNC7011 Flexible PCB XNP7026 Remote Control Unit CXC5717 Transistor(Q751,901) 2SD2396 Cover CZN5357 IC(IC911) NJM2388F84 ••••• IC(IC351) PAL007C Drive Unit CXC8072 Holder See Contrast table(2) Screw BMZ26P040FTC Screw See Contrast table(2) Screw(M2 x 2) CBA1871 Cushion CNN1405 Cord CDE7392 DEH-P690UB/XN/UC...
Page 12
(2) CONTRAST TABLE DEH-P690UB/XN/UC , DEH-P6900UB/XN/UC and DEH-P7950UB/XN/ES are constructed the same except for the following: Mark Description DEH-P690UB/XN/UC DEH-P6900UB/XN/UC DEH-P7950UB/XN/ES Panel CNS8914 CNS8915 CNS8915 Tuner Amp Unit CWN2152 CWN2152 CWN2154 Connector(CN661) CKS4124 CKS4124 Not used Holder CND3782 CND3782 CND3783...
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". Large size SCH diagram Guide page Detailed page +2.2dBm R530 470 CN701 +0.6dBm R556 2R2K R555 2R2K +2.2dBm -24dBm XXA7400 ANTENNA SW UNIT DEH-P690UB/XN/UC...
Page 19
No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. DEH-P690UB/XN/UC...
Page 33
4LOEJ 312SNS 5 V/div 5 V/div 1 V/div 4LOEJ 0FIN 5 V/div 1 V/div 12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 µm) during play Ref.: Ref.: Ref.: REFO Mode: Mode: Mode: Normal Normal Normal DEH-P690UB/XN/UC...
For further information for respective destinations, be sure to check with the schematic dia- CORD ASSY WIRED REMOTE INPUT gram. 2.Viewpoint of PCB diagrams Capacitor Connector IP-BUS SIDE A SIDE B Chip Part P.C.Board DEH-P690UB/XN/UC...
Page 35
SIDE A ANTENNA AUX IN RCA OUT REAR OUTPUT CN701 CN1801 FRONT DEH-P690UB/XN/UC...
Page 36
TUNER AMP UNIT TEST1 PCL1 DEH-P690UB/XN/UC...
4.4 CD CORE UNIT(S10.5COMP2) CD CORE UNIT(S10.5COMP2) SIDE A CN701 PICKUP UNIT(P10.5)(SERVICE) LOADING /CARRIAGE MOTOR SPINDLE MOTOR DEH-P690UB/XN/UC...
Page 41
CD CORE UNIT(S10.5COMP2) SIDE B DEH-P690UB/XN/UC...
IC 551 (A,60,41) SD-RAM(64M) HY57V641620ETP-H IC 561 (A,52,77) IC AK4388VT D 152 (B,74,96) Diode MALS068X D 161 (A,50,96) Diode 1SS355 IC 562 (A,42,83) IC NJM2872BF05 D 162 (A,50,102) Diode RB160L-40 IC 563 (A,42,73) IC NJM4558MD D 163 (A,46,107) Diode 1SR154-400 DEH-P690UB/XN/UC...
Page 43
RS1/16S223J R 309 (A,140,125) RS1/16S390J L 841 (A,131,24) Chip Coil LCTAW100J2520 R 310 (A,150,127) RS1/16S390J L 851 (A,47,17) Chip Coil LCTAW4R7J2520 R 311 (B,142,136) RS1/16S223J L 852 (A,31,18) Inductor CTF1660 R 312 (B,144,136) RS1/16S223J L 871 (A,142,17) Ferri-Inductor LAU4R7K DEH-P690UB/XN/UC...
Page 44
R 533 (A,80,66) RS1/16S101J R 621 (B,147,56) RS1/16S104J R 622 (B,132,43) RS1/16S104J R 535 (A,78,75) RS1/16S102J R 623 (B,118,39) RS1/16S472J R 536 (A,57,55) RAB4CQ101J R 624 (A,142,57) RS1/16S472J R 537 (A,81,63) RAB4CQ101J R 538 (A,57,73) RS1/16S101J R 625 (B,139,77) RS1/16S103J DEH-P690UB/XN/UC...
Page 45
R 912 (A,17,86) RS1/16S473J C 273 (B,121,122) CKSQYB225K10 R 913 (B,41,61) RS1/16S103J C 274 (B,111,123) CKSQYB225K10 R 914 (B,40,68) RS1/16S103J C 275 (A,121,123) CCSRCH101J50 R 921 (A,65,108) RS1/16S103J C 276 (A,111,123) CCSRCH101J50 C 277 (A,117,120) CKSRYB105K10 R 922 (A,68,111) RS1/16S103J DEH-P690UB/XN/UC...
Page 46
CKSRYF104Z50 C 522 (A,80,67) CKSRYB104K16 C 523 (A,80,79) CCSRCH5R0C50 C 841 (A,130,21) CKSRYB473K25 C 524 (A,80,75) CCSRCH150J50 C 842 (A,132,21) CCSRCH101J50 C 525 (A,68,85) CKSRYB103K50 C 851 (A,132,17) 4.7 µF CCG1111 C 526 (B,57,72) CCSRCH100D50 C 852 (A,36,37) CEJQ470M25 DEH-P690UB/XN/UC...
Page 47
(A,129,5) LED CL-197HB1-D(CDE) R 1931 (B,67,25) RS1/16S101J D 1842 (A,67,23) LED CL-197HB1-D(CDE) R 1932 (B,69,27) RS1/16S103J R 1933 (B,70,21) RS1/16S2R2J D 1901 (B,82,20) Diode 1SS355 R 1951 (B,127,10) RS1/16S222J L 1951 (B,117,14) Inductor CTF1617 L 1961 (B,145,22) Inductor CTF1617 DEH-P690UB/XN/UC...
Page 48
C 223 (B,45,53) CCSSCH4R0C50 R 103 (B,60,71) RS1/10SR2R7J C 224 (A,43,55) CKSSYB104K10 R 104 (B,52,69) RS1/16SS222J C 226 (A,40,58) CCSSCH680J50 R 105 (B,41,57) RS1/16SS102J C 227 (A,40,60) CCSSCH470J50 C 228 (A,39,62) CKSSYB103K16 R 107 (B,41,59) RS1/16SS105J R 202 (B,32,62) RS1/16SS473J DEH-P690UB/XN/UC...
Page 49
C 704 (B,8,36) CKSSYB102K50 C 711 (A,25,26) CKSSYB104K10 Unit Number : CWS1389 Unit Name : Switch Unit (B,7,14) Switch(OPEN) CSN1051 (B,29,12) Spring Switch(CLOSE) CSN1052 Miscellaneous Parts List Pickup Unit(P10.5)(Service) CXX1942 Motor Unit(SPINDLE) CXC7134 Motor Unit(LOADING/CARRIAGE) CXC4026 Motor Unit(FLAP) XXA7400 DEH-P690UB/XN/UC...
1k ohms in series. The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. DEH-P690UB/XN/UC...
Page 51
When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the same time all the self-adjusting values shall return to the default setting. DEH-P690UB/XN/UC...
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. Hint Reloading the disc changes the clamp position and may decrease the "wobble". DEH-P690UB/XN/UC...
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. DEH-P690UB/XN/UC...
The frequency of the clock signal is 468.750 kHz that is one 32th of the fundamental frequency. The clock signal should be 468.750 kHz ± 19 Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one. DEH-P690UB/XN/UC...
D e v i c e I n Now connecting C o n n e c t Indication of connection mode M S C When a device supporting mass storage class is connected: H I D When iPod is connected: DEH-P690UB/XN/UC...
- Removing the CD Mechanism Module (Fig.1) Remove the four screws. Disconnect the connector and then remove the CD Mechanism Module. Fig.1 - Removing the Grille Assy (Fig.2) Remove the four screws. Disconnect the connector and then remove the Grille Assy. Grille Assy Fig.2 DEH-P690UB/XN/UC...
Page 58
- Removing the Tuner Amp Unit (Fig.3) Remove the screw. Remove the screw. Straighten the tabs at three locations indicated. Remove the screw and then remove the Tuner Amp Unit. Tuner Amp Unit Fig.3 DEH-P690UB/XN/UC...
Page 59
Upper Frame. 3. While lifting the Carriage Mechanism, remove it from the three Dampers. Caution: When assembling, be sure to apply some alcohol to the Dampers and assemble the mechanism in a clamped state. Damper Damper Carriage Mechanism Lower Frame DEH-P690UB/XN/UC...
Page 60
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load Carriage Motor Assy, do not make them loose over the Feed Screw. Poly Washer Change Arm Pickup Lock Arm Inner Holder Feed Screw Planet Gear Pickup Rack Chassis Pickup DEH-P690UB/XN/UC...
Page 65
Mode setting input 1. Pull-down for normal operation. MODE1 USBH0_DN USB host port 0 D- signal USB host port 0 D+ signal USBH0_DP Digital ground USB host port 1 D- signal USBH1_DN USB host port 1 D+ signal USBH1_DP Power for USB I/O (3.3 V) VDDUSB DEH-P690UB/XN/UC...
Page 66
Digital power for I/O (3.3 V) VDDIO External interrupt request [0]-[3] 120-123 EXINT[0]-[3] Digital power for internal core (1.8 V) VDDI External bus data bit [0]-[3]. Internal pull-up resistor enabled at reset. 125-128 XD[0]-[3] TCC8600-00X-EA-AG PML016B - Pin Layout DEH-P690UB/XN/UC...
Page 68
SPI master-to-slave data SPI_SIMO SPI slave-to-master data SPI_SOMI SPI_UCLK SPI clock Not used 22-31 CLOCK_OUT 32.768 kHz clock output, if selected by CLOCK_ENAB Not used 33-37 CP reset (active low) nRESET Supply voltage, negative terminal Supply voltage, positive terminal DEH-P690UB/XN/UC...
Page 69
FLPCLS Flap open operation output FLPOPN USBTESTTRK TrackUP operation terminal(In USB test mode, I/O : I) TrackUP operation terminal USBTESTNOW USBTESTNG OK/NG output terminal EVOL : Mute EMUTE Level indicator clock output SACLK TESTIN terminal for USB only USBTESTIN DEH-P690UB/XN/UC...
Page 70
Reference voltage input VREF Analog power supply input AVCC P-BUS : Input/Test program : data input BSI/TSI P-BUS : Output/Test program : data output BSO/TESTDO P-BUS : Clock output/Test program : clock output BSCK/TSCK PEG301A Format Meaning CMOS Nch open drain DEH-P690UB/XN/UC...
Page 71
NJM2872BF18 NJM2872BF05 - Block Diagram - Pin Layout VOUT 1. VIN 2. GND CONTROL 3. CONTROL Thermal 4. NOISE BYPASS Protection 5. VOUT NOISE BYPASS Bandgap Reference HY57V641620ETP-H PE5547A Format Meaning CMOS Nch open drain DEH-P690UB/XN/UC...
Page 72
Power supply for the crystal oscillator X.VDD DA.VDD Power supply for DAC Output of audio for the left channel LOUT DA.GND Ground for DAC Connected to the capacitor for band gap REGC Ground for DAC DA.GND Output of audio for the right channel ROUT DEH-P690UB/XN/UC...
Page 73
Output of reference voltage REFOUT Reversal input of FE Output of FE FE,TE A/D converter input ADCIN Reversal input of TE Output of TE Output of LD Input of PD Power supply for servo ADC AD.VDD Ground for servo ADC AD.GND DEH-P690UB/XN/UC...
Page 74
Image ROM : Address bus 9 bit VCC2 Power supply input Image ROM : Address bus 8 bit VSS2 Image ROM : Address bus 7 bit Image ROM : Address bus 6 bit Image ROM : Address bus 5 bit DEH-P690UB/XN/UC...
Page 75
Key data 3(Not used) kd@,! Key data 2,1 92,93 AVSS Analog GND Key data 0 Reference voltage input VREF Analog power supply input AVCC Terminal for Dimmer control 99,100 Not used PEG312A8 Format Meaning CMOS Nch open drain PD8174A PD8173A DEH-P690UB/XN/UC...
Page 76
22 AUDIOGND audio ground Ground of audio block 23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output 24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output DEH-P690UB/XN/UC...
Source keys If the time interval is not 500 msec, the oscillator operative may be defective. Source ON SYSPWtH *2 *2 AMPPW operates at the same time. Pin 1 Completes power-on operation. (After that, proceed to each source operation) DEH-P690UB/XN/UC...
CD Mechanism Module Grease GEM1069 EXTERIOR Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools CD pickup lenses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DEH-P690UB/XN/UC...