Related Manuals for IDENTEC SOLUTIONS i-B350L W
Summary of Contents for IDENTEC SOLUTIONS i-B350L W
- Page 1 ILR 350 Series i-B350L W, Wristband Tag Installation and Operation Manual PRELIMINARY...
- Page 2 Proprietary Notice This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or disclosed to other parties in whole or in part without prior written authorization from IDENTEC SOLUTIONS. Disclaimer and Limitation of Liability IDENTEC SOLUTIONS AG and its affiliates, subsidiaries, officers, directors, employees and agents do not make any express or implied warranties or representations with respect to such information including, without limitation, warranties as to non-infringement, reliability, suitability for a particular purpose and accuracy.
- Page 3 The user(s) of these products are cautioned to only use accessories and peripherals approved, in advance, by IDENTEC SOLUTIONS. The use of accessories and peripherals, other than those approved by IDENTEC SOLUTIONS, or any changes or modifications not expressly approved by the party responsible for compliance could void the users’...
-
Page 4: Table Of Contents
Contents INTRODUCTION ......................5 ....................... 5 REPARATIONS ....................5 ECOMMENDED ROCEDURE ....................5 COPE OF THIS OCUMENT ......................5 ESPONSIBILITY ....................5 SSOCIATED OCUMENTS —V ................5 COPE OF ELIVERY ISUAL NSPECTION SAFETY PRECAUTIONS ....................6 GENERAL ........................8 ................. 8 PTICAL DENTIFICATION OF THE ......................... -
Page 5: Introduction
An additional performance check of the tags and a system test can now be done Scope of this Document This document is the users’ manual of the models i-B350L W and i-B350L W-PB. This document is intended only for mechanical installation rsp. everyday use. -
Page 6: Safety Precautions
Safety Precautions Important Safety Note The devices described in this manual are for exclusive operation by trained employees. Only qualified personnel that know the potential dangers involved should perform the installation, settings, maintenance and repair of the units used. Operational Safety The correct and safe use of these systems assumes that operating and service personnel follow the safety measures described in the manual alongside the generally acceptable safety procedures. - Page 7 Spare Parts We recommend that only original products, spare and replacement parts authorized by IDENTEC SOLUTIONS be used for installation, service and repair. Otherwise IDENTEC SOLUTIONS does not accept any responsibility for materials used, work carried out or possible consequences.
-
Page 8: General
General Optical Identification of the Tag The wristband is available in two options. With or without Push Button. The label on the back side of the tag, is protected by the wristband. In order to inspect it slightly lift up the wristband between the two loops of the tag housing. -
Page 9: Accessories
Accessories Multi use NATO wristband P/N: 439471 Single use, temper proof vinyl wristband. P/N: 439370 VISIBILITY DELIVERED. PAGE 9 OF 21... -
Page 10: Configuration Of The Tag
Important Note Do not open the housing! Configuration is done using the built-in air interface of the i-B350L W. In addition to the Broadcast mode the i-B350L W offers the following special functions that can be configured: Bursts on entering a marker field can be configured independent from regular Pings ... -
Page 11: Ping Rate
Ping Rate Note: This settings can be found in the ILR Tag Configuration software tool in the edit block ―Broadcast‖ Broadcast Interval: 0 = no broadcast messages are sent, value > 0 = Broadcast interval in seconds. This can be set in steps of 0.5 sec, from 0.5 to 300 seconds. ... -
Page 12: Information On Burst Settings
Marker | Push Button | User Data => max. 32 Bytes Bytes of user data Push Button | User Data => max. 43 Bytes of user data Push Button | User Data | Marker => max. 32 Bytes of user data Information on Burst Settings The parameter ―Time between Bursts (Marker)‖... -
Page 13: Tag Mounting Techniques
Tag Mounting Techniques Multi use NATO wristband Mounting tag on wristband Put the longer strap through the holder on the housing first from the top side to the bottom side, and then from the bottom-side to the top side, so that the tag is on top side of the wristband. VISIBILITY DELIVERED. - Page 14 Shift the tag back on the longer strap, as far as possible. Put the longer strap through the ring of the shorter one and tight it up. Correct assembled wristband tag with multi use NATO wristband. VISIBILITY DELIVERED. PAGE 14 OF 21...
- Page 15 The tag is carried the same as any standard wristwatch. The band should not be too loose. This avoids that the tag slides down over the wrist and prevents possible injury. For maximum convenience put the end of the wristband through the two metallic loops. VISIBILITY DELIVERED.
-
Page 16: Single Use Vinyl Wristband
Single use vinyl wristband Put the tag on the blue-side-up wristband. Put the strap from the up side to the lower side and then from the lower side to the top side. Correct assembled wristband tag with single use vinyl wristband. VISIBILITY DELIVERED. - Page 17 The tag is carried the same as any standard wristwatch. The band should not be too loose. This avoids that the tag slides down over the wrist and prevents possible injury. Close the plastic fastener by pushing it from top until a clicking noise can be heard. VISIBILITY DELIVERED.
- Page 18 To remove the wristband, cut it carefully with scissors. To avoid serious injuries, do not use a knife to remove the tag. VISIBILITY DELIVERED. PAGE 18 OF 21...
-
Page 19: Maintenance
Parts or main components returned for repair or exchange must be handled with great care. PC cards must be returned in the appropriate ESD-protecting packaging material. All returns should include an error description and a short application overview and be sent to the local distributor or to: IDENTEC SOLUTIONS AG Service Department Millenium Park 2... -
Page 20: Technical Data
Technical Data Operating Data Operating frequency ILR-RFID 868 MHz (EU) or 920 MHz (NA) Maximum transmission power 0.75mW (EU / NA) Compatibility i-PORT M 350, i-CARD CF-350 Standards/Certification FCC Part 15 (US), ETSI EN 300 220 (EU) Communication Data Long-Range RFID (ILR, Beacon Technology) Read range broadcast Up to 150 m (490 feet) free air* Operation mode... - Page 21 Dimensional Drawing Dimensions in mm VISIBILITY DELIVERED. PAGE 21 OF 21...