Advertisement
RISK OF ELECTRIC SHOCK!
DO NOT OPEN!
Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock.
Use only high-quality professional speaker cables with ¼" TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel.
To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus.
These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.
MUSIC Group accepts no liability for any loss which may be suff ered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2016 All rights reserved.
Optional:
The Harmony knob selects a single harmony voice or combination of voices higher or lower in pitch than your voice. The chart below shows name and pitch intervals for each position on the Harmony knob.
Icon | Name | Interval |
High | 3rd above | |
Higher | 5th above | |
High and Higher | 3rd above 5th above | |
Low | 4th below | |
Lower | 6th below | |
Low and Lower | 4th below 6th below | |
Higher and Lower | 5th above 6th below | |
High and Low | 3rd above 4th below |
Connect any guitar pedals between Harmony Singer's Guitar Output jack and the input of your amp. Connecting and activating some guitar pedals before the Guitar Input jack may adversely affect vocal harmony production.
Tips:
The standard function of the footswitch is a latching style, meaning that each press of the footswitch turns the harmony on and off. Alternatively, the pedal can operate in momentary mode, meaning that the harmony is only active while the footswitch is held down. As soon as you release the footswitch, the harmony is bypassed.
To switch the unit to momentary mode, hold the Tone button down while powering the unit on. Repeat the process to return to latching mode.
Harmony Singer 2 can operate on 4 AA batteries. Remove the single screw on the bottom of the pedal to open the battery door. Make sure to observe correct polarity when inserting the batteries.
Harmony Singer 2 will automatically adjust the gain setting for your microphone, eliminating the need for manual adjustments and ensuring that a good signal is passed to the mixer without any unwanted distortion.
Phantom power is always active on the Harmony Singer 2. This will power condenser microphones, but will not affect dynamic mics either.
Mic Control allows you to control the effect's on/off status via an MP-75 microphone. Press and hold the footswitch while powering up the unit to toggle Mic Control.
Note that when using a condenser microphone, Mic Control should be disabled to prevent unwanted on/off switching.
Input | |
Mic Input Impedance: | Balanced 2.68 kOhm |
Mic Input Level @ 0 dBFS: | -42 dBu to +1 dBu |
EIN @ Max Mic Gain Rg = 150 Ohm: | -126 dBu |
Mic input SNR: | >104 dB |
Guitar Input impedance: | 1 MOhm |
Guitar Input Level @ 0 dBFS: | -7 dBU to 17 dBu |
Guitar Input SNR: | >115 dB |
Output | |
Output Impedance, Bal./Unbal.: | 200/100 Ohm |
Output Full Scale: | +1 dBu |
Dynamic Range: | >104 dB, 20 Hz to 20 kHz |
Frequency Response: | +0/-0.3 dB, 20 Hz to 20 kHz |
Power | |
Power Supply (Supplied): | 9 V / 670 mA |
Power Consumption: | 6 W |
Requirements | |
Operating Temperature: | 32°F to 122°F (0°C to 50°C) |
Storage Temperature: | -22°F to 167°F (-30°C to 70°C) |
Humidity Max.: | 90% non-condensing |
Size & Weight | |
Dimensions: 5.4" x 3.5" x 2.3" (140 x 90 x 60 mm) Weight: 0.92 lb. (420 g) |
Due to continuous development, these specifications are subject to change without notice
For the applicable warranty terms and conditions and additional information regarding MUSIC Group' s Limited Warranty, please see complete details online at music-group.com/warranty.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download TC Helicon HARMONY SINGER 2 - Battery-Powered Vocal Effects Stompbox Manual
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the HARMONY SINGER 2 that isn't answered in the manual? Leave your question here.