Page 1
USER MANUAL Electric Vehicle AC Charger Copyright Any part of this manual, including text, pictures, graphics, etc., belongs to Hangzhou Livoltek Power Co., Ltd. Without written permission, no unit or individual may extract, copy, translate 1418-35 Moganshan Road, Hangzhou City, China or modify all or part of this manual in any way.
Please start and stop the charging according to the user manual and relevant prompts provided Please read this manual carefully before using the charger and keep it for future reference. by LIVOLTEK. When plugging in and out the vehicle connector, pay attention to the appropriate force and press the unlock button (Type 1).
4.1 Product appearance vehicle connector and vehicle inlet are found to be damaged by melting and foreign matters, please stop using the charger immediately and consult the LIVOLTEK customer service for proper treatment. For the unused charger, it is recommended to disconnect the circuit breaker associated with the charger to prevent power loss or unknown accidents.
Relay fault Electrical protection The LIVOLTEK charger has the functions of overvoltage protection, undervoltage protection, Note: “G” stands for green light, “B” stands for blue light, “R” stands for red light, “ ” stands for overcurrent protection, short circuit protection, leakage protection and grounding protection.
4.6 Charging modes In this mode, it is a mixture of green energy and energy imported from the grid and LIVOLTEK battery pack. ECO mode minimises the use of grid power and can charge using 100% green energy. Fast mode If the surplus generation drops below 1.4kW, extra power will be drawn from LIVOLTEK battery...
5mm distance from the mounting surface. It is recommended that the charger be installed by an authorized service provider of LIVOLTEK. The installation position of charger shall not be close to dangerous positions such as water pipe, gas pipe and steam pipe.
Column mounted installation 104mm 1. Drill four installation holes (Φ12X120 mm) on the cement base according to the column installation hole 5. Thread the hook through the cable and tighten the 5 screws. diagram. Note: the height of the cement base shall ensure that the 64mm lowest point of the vehicle connector when stored shall be located at a height between 0.5m and 1.5m above ground...
Unit: mm 5.5 Input cable preparation 5.6 Communication network cable preparation A0070230E11/A0070230E12 It is recommended that the specification of AC incoming cable is 3x6mm², the specific treatment If the charger needs RS485 communication, it is recommended to adopt EIA /TIA 568B method of incoming cable is shown in the figure below:...
Note: It is recommended to connect one 1P + N + PE surge protection device (Class C) at the front end of the incoming line of the charger, A0070230E11/ A0070230E12 corresponds to 1P + N + PE surge ④ protection device, A0110400E11/A0220400E11 correspond to 3P + N + PE surge protection device.
The detailed wiring of the electricity meter and inverter shall be subject to the equipment requirements. 1 Access the charger via Bluetooth. Step 1: Open LIVOLTEK APP, enter “Local Mode > Bluetooth RJ45 Mode” on the login page, and select the charger for access.
Page 12
Note: Only 1 mode can be enable at the same time. “Dynamic Mode” needs to be used with the electricity meter, and “ECO Mode” needs to be used with the LIVOLTEK inverter and energy storage system. Note: If you have a LIVOLTEK solar ESS system, you can 3 Start-up charging.
Step 3: After successful creation, return to the home page. You 6 View historical alarms. can see that the schedule has been “on hold” and the state of Enter the alarm center page through the “ ” icon at the top of the charger has changed to “Scheduled”.
There are clear requirements and conditions for the transportation, storage, installation and use Your Contact Number of electric vehicle charger. LIVOLTEK is not responsible for providing free relevant services, technical support or compensation, including but not limited to: Your Email Address The charger has expired the warranty period and has not purchased extended warranty service.