FLOWTECH flowcon Operation And Maintenance Manual
Vsd - j inverter
Hide thumbs
Also See for flowcon:
- Operation and maintenance manual (39 pages) ,
- Operation and maintenance manual (24 pages) ,
- Operation and maintenance manual (22 pages)
Related Manuals for FLOWTECH flowcon
Summary of Contents for FLOWTECH flowcon
- Page 1 flow © VSD - J Inverter OPERATION AND MAINTENANCE MANUAL First Publication Date: 01/09/2020 Revision: Revision Date:...
-
Page 2: Table Of Contents
OPERATION & MAINTENANCE CONTENTS Description Technical Data Product Identification Size and Weight Storage Installation and assembly Electrical Connections Screen Format Main Screen Operation Mode Start Up Wizard The Setup Menu Warning Management Alarms Maintenance and Repair Warranty Disposal and Environmental Aspects... - Page 3 General Information These instructions are to assist in the installation of the flowcon VSD -J Inverter please follow them carefully. If, having read this Operation & Maintenance Manual, there is any doubt about any aspect of the installation please don't hesitate to contact our technical team.
- Page 4 Water Solutions. This document is intended for ALL installers, operators, users and persons carrying out maintenance of this equipment and must be kept with the equipment, for the life of the equipment and made available to all persons at all times.
- Page 5 Wait more than 5 minutes after turning off the power supply before performing maintenance or inspection. Hazard of electric shock. Disconnect incoming power before working on this unit. WARNING! - The inverter should be protected separately against ground fault. HAND-PAP Observe the regional regulations for electrical installation! flowcon VSD - J Inverter...
- Page 6 exclamat CAUTION! - It is strongly recommended that all electrical equipment conforms to National Electrical Codes and local regulations. Only qualified personnel should perform installation, alignment and maintenance. The manufacturer reserves the right to alter the technical data in order to make improvements or update information. exclamat CAUTION! - Failure to observe these rules will render the guarantee invalid.
-
Page 7: Description
The product must be stored in a covered and dry place, away from sources of heat and protected from dirt and vibrations, moisture, heat sources and possible mechanical damage. Do not place heavy objects on top of the packaging. flowcon VSD - J Inverter... -
Page 8: Installation And Assembly
Installation and assembly Before installing the frequency inverter, carefully read the whole of this manual and consult the safety regulations in force in the country in which it will be used. The installation must be carried out by a qualified technician. - Page 9 Place the inverter assembly inside the wall bracket, ensuring that the 2 ends of the metal radiator are inside the wall bracket. Fix the inverter to the wall bracket using the two side screws drilled into the metal radiator (part 14). flowcon VSD - J Inverter...
-
Page 10: Electrical Connections
Electrical Connections It is necessary to install a magnetic core (A). You will find it in the accessories box. It must be fitted to: (MT) the power cable of the frequency inverter, as close as possible to the cable gland. (TT) the cable between frequency inverter and motor, as close as possible to the frequency inverter connector, until a click (B) is heard. -
Page 11: Screen Format
(maximum 8). They are connected point to point. The “1” terminals must be connected together in the same way as the “2” terminals Screen Format flowcon VSD - J Inverter... -
Page 12: Main Screen
Main Screen Current rotation frequency Instant consumption Nominal consumption Stop frequency Current Time Current Pressure Working Pressure Access to the menu Operation Mode The operation mode of the inverter will continuously seek to minimise the electricity demand, at the same time guaranteeing minimum wear to the pumps. -
Page 13: Start Up Wizard
Note: the nominal consumption is indicated on the specifications plate of the motor. You must choose the correct value, for example if you connect an inverter MT2200 select the value 230V and for the TT4000 select the value 400V. flowcon VSD - J Inverter... - Page 14 Use the arrow keys to enter the maximum range for the pressure of the transducer connected. This value is indicated on the specifications plate of the pressure transducer and must always be between 4 and 20 mA. Validate this with F2. Use the arrow keys to enter the pressure at which you want the unit to work.
-
Page 15: The Setup Menu
5.22 Low Water Level Alarm Active 5.23 Low Water Level Alarm Delay 5.24 Burst Pipe Alarm 5.25 Voltage Alarm Active 5.26 Parameter Lock 5.27 Set Date and Time 5.28 Stop Adjustment Input Wizard flowcon 5.29 Factory Settings VSD - J Inverter... - Page 16 1. Parameters Programming Parameter Description Units Notes Default Min. Max. Working Wizard 0.5 Pressure you wish to maintain in the Pressure system. Motor Current Amp Wizard 0.1 Current of the motor in amperes. Taking into account whether your motor is wired as three phase 230V or three phase 400V.
- Page 17 When you access this menu this screen appears: ͦ Attention: Improper use of manual mode can cause overpressures in the installation. flowcon VSD - J Inverter...
- Page 18 5. Advanced Parameters Programming Parameter Description Units Notes Default Min. Max. 5.01 Language Spanish Spanish Dutch You can select between different language for the menu and the English Polish warning French 5.02 Units of Bar - Psi Units of working pressure and display Pressure 5.03 Maximum...
- Page 19 Wizard 5.29 Factory To reset the unit and leave t with the factory settings, change this Settings parameter to “YES” and after you have entered the code 1357 the unit will launch the start-up wizard. flowcon VSD - J Inverter...
-
Page 20: Warning Management
6. Fine Tuning Programming Parameter Description Units Notes Default Min. Max. 6.01 Proportional Constant 6.02 Integral Constant 6.03 Switching 16.0 Frequency 6.04 Stop Switching Range 6.05 Stop Switching Speed 6.09 Alarms Reset If you change this parameter from “NO” to “YES” you will reset the alarms log and parameter automatically returns to “NO”. -
Page 21: Alarms
Alarm F02 Short Circuit The motor is Disconnect the motor from the inverter and check that the communicated or has message disappears. If this is not the case, contact Flowtech burnt out. Water Solutions. Not all wires have been Check that all the cables of the motor are correctly connected to connected. -
Page 22: Maintenance And Repair
Alarm F06 Motor Fault The motor has Disconnect the motor from the inverter and check that the communicated or has message disappears. If this is not the case, Contact Flowtech burnt out. Water Solutions. Fault/ poor connection of the phases. -
Page 23: Disposal And Environmental Aspects
This stipulation only refers to the disposal of equipment within the European Union (2012/19/EU). It is the user’s responsibility to dispose of the equipment by delivering it to a designated collection point for the recycling and disposal of electrical equipment. flowcon VSD - J Inverter... - Page 24 Unit 1 Lock Flight Buildings, Wheatlea Industrial Estate, Wigan, Greater Manchester WN3 6XP United Kingdom 9001 : 2015 REGISTERED Membership No. 700106 Certificate No. 185352020 Copyright © 2020 • All Rights Reserved • Flowtech Water Solutions Limited • Company Number: 05125479 • VAT Number: 836 8024 19...