Subscribe to Our Youtube Channel
Related Manuals for RJWC CFMOTO CFORCE 850 XC
Summary of Contents for RJWC CFMOTO CFORCE 850 XC
- Page 1 CFMOTO CFORCE 850/1000 XC Floorboards Installation Manual Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 2 Read carefully before installation! Before starting installation, make sure your ATV is off, and has cooled down. To start the installation of the RJWC Floorobards you will need to remove the stock floorboards. You may also need to remove plastic covers of the wheel arch. The plastic pegs that hold these in place may break while being removed, but don’t worry - we...
- Page 3 CFORCE 850/1000 XC Floorboards Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 4 Review the next image for how the panels look assembled. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 5 Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 6 The Upper Bracket for each side will have the ‘lip’ facing outwards. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 7 The diagonal bend line should ‘point away’ from the panel. Do not install the other Screw & Nut. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 8 With the Panel 1R prepared, you can slide this into place at the front of the footwell. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 9 The tab on the bottom floor panel 3R, MUST go behind the 1R panel. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 10 Use 1x Screw to fasten this panel. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 11 Use 4x Screws to secure Panel 8R and the baseboard into place against the frame of the ATV. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 12 On the back of panel 1R, use 1x Screw and 1x Nut to secure the panel to the plastic of the ATV. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 13 Slide the Panel 2R behind the 1R Panel and secure in place with 3x Screws and 3x Nuts. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 14 Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 15 Slide the Panel 9R behind the rear footrest panel (6R) and secure with 3x Screws and 3x Nuts. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 16 Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 17 To adjust their angle, you can loosen a screw, pivot them and retighten. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 18 Install the Panel 4R on to the bottom of your ATV using the frame bars. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 19 Install the second Screw and Nut into the Line Bracket, connecting it to the 8R Bracket. Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
- Page 20 Need help? Got a question? Or just want to tell us about your day: support@rjwc.se support@rjwc.se Get in touch at: Bolts with a red circle ( ) next to them do not need a nut. These are secured by a fixed fastener. © 2023 RJWC Powersports EU www.RJWCPOWERSPORTS.com...
Need help?
Do you have a question about the CFMOTO CFORCE 850 XC and is the answer not in the manual?
Questions and answers