Subscribe to Our Youtube Channel
Related Manuals for Benchmark 1282-204
Summary of Contents for Benchmark 1282-204
- Page 1 18 GAUGE PNEUMATIC BRAD NAILER 5 Year Limited Warranty WEAR CSA WEAR EAR WEAR A APPROVED EYE PROTECTIO N FACE PROTECTION MASK...
- Page 2 PRODUCT SPECIFICATIONS 18 Gauge Pneumatic Brad Nailer Magazine Capacity 100 Nails Fastener Capacity 18 Gauge 5/8” to 2” Long Max Pressure 120 PSI Average Air Consumption 0.3 CFM @ 90PSI Working pressure 70-110 PSI MAGAZINE ANGLE 90° Air inlet 1/4” NPT Recommended hose 1/4"...
-
Page 3: Table Of Contents
1282-204 18 GAUGE PNEUMATIC BRAD NAILER TABLE OF CONTENTS Product Specifications ....................1 Table of Contents ....................... 2 Safety Guidelines ....................3-6 Symbols ........................6 Tool Specific Warnings ....................7 Know your Pneumatic Brad Nailer ................8 Assembly and Operating ..................9-16 Maintenance ...................... -
Page 4: Safety Guidelines
SAFETY GUIDELINES WARNING: This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. - Page 5 1282-204 18 GAUGE PNEUMATIC BRAD NAILER SYMBOL MEANING Do not use oxygen or any other combustible or bottled gas Oxygen to power air-powered tools. Failure to observe this warning can cause explosion and serious personal injury or death. nydrogen Use only the compressed air to power the air-powered explosive tools.
- Page 6 DANGER! Keep children away from the work area. Do not allow children to handle power tools. Keep air hose away from heat, oil, and sharp edges. Check air hose for wear before each use and ensure that all connections are proper. Always ensure that the workpiece is firmly secured leaving both hands free to control the tool.
-
Page 7: Symbols
1282-204 18 GAUGE PNEUMATIC BRAD NAILER CAUTION! Disconnect tool from the air supply and turn off the compressor before performing any maintenance or changing accessories, when clearing a jammed fastener, when the tool is not in use, when it is being handed to another person, and when it is left unattended. -
Page 8: Tool Specific Warnings
TOOL SPECIFIC WARNINGS Keep hands and other parts of the body away from the firing head during use. Keep hands, feet, and all other parts of the body at least 8"(20 cm) away from the firing head. Nails or objects in the workpiece can cause serious injury if they are deflected by the workpiece or if they are driven away from the point of entry. - Page 9 1282-204 18 GAUGE PNEUMATIC BRAD NAILER KNOW YOUR 18 GAUGE BRAD NAILER No. Description No. Description Air inlet plug Depth adjustment dial Magazine latch Trigger Magazine Air exhaust deflector Safety tip Mode Selection Switch Quick Nail Extraction lever...
-
Page 10: Assembly And Operating
ASSEMBLY AND OPERATING The 18 Gauge Pneumatic Brad Nailer delivers superior power - easily driving 2“brad nails through solid oak. Tool-free depth adjustment makes it easy to work with various dimensions of trim and molding. The super-narrow tool body and nose make it easy to get precise positioning in corners and tight spots. - Page 11 1282-204 18 GAUGE PNEUMATIC BRAD NAILER AIR SYSTEM Always use clean, dry, regulated, compressed air at 4.8 to 7.5 bar (70 to 110 PSI) Do not exceed the maximum or minimum pressures. Operating the tool at the wrong pressure (too low or too high) will cause excessive noise or rapid wear of tool.
- Page 12 Air tools Read this Instruction Manual carefully before using the tool Read and follow all the safety instructions at the beginning of this manual. Inspect the air- powered tool prior to each use in order to: -Ensure that the proper power source is being used. -Verify that the tool is in proper working order.
- Page 13 1282-204 18 GAUGE PNEUMATIC BRAD NAILER 2. Hold the Brad Nailer firmly with one hand, and use the other hand to press the latch (1) on the magazine (2) and slide it back. 3. Insert a strip of nails (1) into the magazine.
- Page 14 The Brad Nailer has a depth adjustment dial below the trigger to adjust the firing depth of the fasteners. Note: Refer to the graphic imprinted below the trigger and adjust the firing depth accordingly. DECREASING FASTENER DEPTH Turn the depth adjustment dial counterclockwise (with the discharge area of the tool facing away from the operator).
- Page 15 1282-204 18 GAUGE PNEUMATIC BRAD NAILER SINGLE SEQUENTIAL ACTUATION MODE The single sequential actuation mechanism is for use where precise fastener placement is desired. The single sequential actuation mechanism may reduce the possibility of bodily injury to you or others in the work area compared to the contact/bump actuation mechanism.
- Page 16 Clearing a jammed nail To clear a jammed nail Disconnect the tool from the air supply line. Remove the non-jammed nails that are stored in the tool’s magazine. Operate the magazine latch and slide the pusher back to open the magazine for checking the jammed nails.
-
Page 17: Maintenance
1282-204 18 GAUGE PNEUMATIC BRAD NAILER Storage When the tool is stored for longer periods of time, apply an ample amount of lubrication before storing. Run the tool for approximately 30 seconds after lubricating, in order to ensure that the lubrication is uniformly distributed throughout the tool. - Page 18 Air-operatedtoolsmustbeinspectedperiodically,andworn orbrokenpartsmustbe replaced in order to keep tools operating safely and efficiency. Inspect and replace worn or damaged 0-rings, seals, etc. Tighten all screws and caps frequently in order to help prevent personal injury. Inspect the trigger, spring, and the safety mechanism for free movement on a regular basis in order to ensure that the safety system is fully functional.
- Page 19 1282-204 18 GAUGE PNEUMATIC BRAD NAILER Problem Possible causes Solutions 1.The bumper is worn. The nails are 1.Replace the bumper. 2.The air pressure is being driven 2. Adjust the air pressure. too high. too deep. 3.Adjust the depth setting by turning 3.The depth...
-
Page 20: Exploded View
EXPLODED VIEW... -
Page 21: Parts List
1282-204 18 GAUGE PNEUMATIC BRAD NAILER PARTS LIST WARNING When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this saw may create a safety hazard unless repairs are performed by a qualified technician. - Page 22 Key# Part # Part Name 1282-204-031 Trigger valve seat 1282-204-032 O-ring 1.7x2 Switch Lever 1282-204-033 O-ring 11.2x2 1282-204-034 Trigger Valve Guide 1282-204-035 1282-204-036 Compressed spring 1282-204-037 Pin case Clamp block 1282-204-038 1282-204-039 Trigger 1282-204-040 Steel ball Dw=3 Fixed spring 1282-204-041...
- Page 23 1282-204 18 GAUGE PNEUMATIC BRAD NAILER Key# Part # Part Name 1282-204-067 Pin case Quick Release Handle 1282-204-068 O-ring 1.9*1.2 1282-204-069 Spacer pin 1282-204-070 1282-204-071 O-ring 41*1.6 End cap 1282-204-072 End cap protection cover 1282-204-073 Bolt M4x14 1282-204-074 Quick coupler...
-
Page 24: Warranty
WARRANTY BENCHMARK WARRANTY If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 25 MEULEUSE PNEUMATIQUE 1282-943 À RECTIFIER LES MATRICES DE 1/4 PO 18 GAUGE PNEUMATIC BRAD NAILER 5-Year Limited Warranty 1282-204 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects...
Need help?
Do you have a question about the 1282-204 and is the answer not in the manual?
Questions and answers