Subscribe to Our Youtube Channel
Related Manuals for Benchmark 1282 206
Summary of Contents for Benchmark 1282 206
- Page 1 PNEUMATIC PIN NAILER 5 Year Limited Warranty READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS PNEUMATIC PIN NAILER Magazine Capacity 100 nails Magazine Angle 90° Pin Nail Size Range 1/2" ~ 1-1/2" long Fastener Capacity Ga 23 (Φ 0.64) Working Pressure 70-110 PSI Average Air Consumption 0.75 CFM @ 90 PSI Air Inlet 1/4”... -
Page 3: Table Of Contents
1282 206 PNEUMATIC PIN NAILER TABLE OF CONTENTS Product Specifications ................... 1 Table of Contents ................... 2 Safety Guidelines ..................3-6 Symbols ....................... 7 Tool Specific Warnings .................. 8 ..............9 Know Your Pneumatic Pin Nailer ............... 10-15 Assembly and Operating .................. -
Page 4: Safety Guidelines
SAFETY GUIDELINES WARNING: This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. DANGER! Potential hazard that will result in serious injury or loss of life. -
Page 5: Symbols
1282 206 PNEUMATIC PIN NAILER SYMBOL MEANING • Risk of inhalation: Never directly inhale the air produced by the compressor. • Risk of bursting: Do not adjust the pressure switch or safety valve for any reason. They have been preset at the factory for this compressor’s maximum pressure Tampering with the... - Page 6 WARNING! • Do not allow unskilled or untrained individuals to operate the air tool. • Do not use the tool for any task other than that it is designed to perform. • Locate the compressor in a well-ventilated area for cooling, and a minimum of 12”...
- Page 7 1282 206 PNEUMATIC PIN NAILER CAUTION! • Disconnect tool from the air supply and turn o the compressor before performing any maintenance or changing accessories, when clearing a jammed fastener, when the tool is not in use, when it is being handed to another person, and when it is left unattended.
-
Page 9: Tool Specific Warnings
1282 206 PNEUMATIC PIN NAILER TOOL SPECIFIC WARNINGS DANGER Potential hazard that will result in serious injury or death. • Do not disconnect or reconnect the air hose with the tool pressed or with a fastener in the guide. The tool may fire when it is reconnected to the air supply. -
Page 10: Know Your Pneumatic Pin Nailer
KNOW YOUR PNEUMATIC PIN NAILER Exhaust deflector Rubber grip Air inlet plug Trigger Magazine Latch Magazine Workpiece Contact... -
Page 11: Assembly And Operating
1282 206 PNEUMATIC PIN NAILER ASSEMBLY AND OPERATING COMPATIBLE COMPRESSORS GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with air-powered tools. The compressor should be able to supply a minimal air delivery of 2.0 SCFM @ 90 psi to ensure the compressor can run continuously with the tool. - Page 12 Air system • Always use clean, dry, regulated compressed air at 4.8 to 7.5 bar (70 to 110 PSI). Do not exceed the maximum or minimum pressures. Operating the tool at the • wrong pressure (too low or too high) will cause excessive noise or rapid wear. No.
- Page 13 1282 206 PNEUMATIC PIN NAILER WARNING! Potential hazard that could result in serious injury or loss of life. • Do not use the tool if it is not in proper working order. • Do not use oxygen or any other combustible or bottled gas to power this tool.
- Page 14 General use 23 Gauge Pin Nailer provides powerful firing of up to 1-3/8” pins into the hardest hardwoods with ease. The lightweight, narrow body tool is easy to handle, making it ideal for cabinet trim. Ideal for detailed woodworking, molding, decorative trim, lightweight paneling, pictures frames plus arts and crafts.
- Page 15 1282 206 PNEUMATIC PIN NAILER Slide the magazine latch (1) against the nails to close the magazine until it comes into contact with the nails (fig C). Plug in compressor, turn it on, set the pressure regulator to 90 psi, attach one end of the air hose to the compressor and the other end of the air hose (2) to the tool (1) (fig D).
- Page 16 If the Workpiece Contact (nose of tool) remains pressed, successive nails will fire each time the trigger is pulled. CAUTION! Potential hazard that may result in moderate injury or damage to equipment • Operate the tool with utmost care when connected with the air compressor. Failure to comply may result in moderate injury or damage to equipment.
-
Page 17: Maintenance
1282 206 PNEUMATIC PIN NAILER MAINTENANCE Note: Do not store the tool anywhere temperatures will fall below freezing. DANGER! Disconnect the tool from the air compressor before maintenance/service, adjusting, cleaning jams, reloading, and when it is not in use. Repairs must be performed by a qualified service technician only. -
Page 18: Troubleshooting
TROUBLESHOOTING The following chart lists common issues and solutions. Please read it carefully and follow all instructions closely. DANGER! Potential hazard that will result in serious injury or loss of life. • If any of the following symptoms appear while the tool is in use, turn it o and disconnect it from the air supply immediately. - Page 19 1282 206 PNEUMATIC PIN NAILER PROBLEM POSSIBLE CAUSES SOLUTIONS The tool jams. 1. Improper nails are used, or 1. Use proper nails. nails are damaged. (see section “Clearing a jammed nail.”) 2. The driver guide is damaged 2. Inspect and replace the driver.
-
Page 20: Exploded View
EXPLODED VIEW... -
Page 21: Parts List
1282 206 PNEUMATIC PIN NAILER PARTS LIST WARNING: When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this tool may create a safety hazard unless repairs are performed by a qualified technician. - Page 22 Key # Part # Part Name Quantity 03.04.32.011 Spring seat 03.04.36.252 Safety shelf spring 03.04.16.093 Safety shelf lock frame 03.04.05.263-03 Spring washer 5 03.04.05.033 Bolt M5x22 03.04.13.059 Drive guide cover 03.04.05.714 Bolt M4x12 03.04.08.039 Drive guide 03.04.13.161 Movable cover 03.04.05.007 Bolt M4x6 03.04.05.003 Bolt M3x8...
- Page 23 1282 206 PNEUMATIC PIN NAILER Key # Part # Part Name Quantity 03.04.29.092 Handle rubber 03.04.01.137 O-ring 35.5x2.3 03.04.11.002-27 End cover 03.04.05.294 Air plug 03.04.29.149 Air plug case 03.04.05.262-03 Spring washer 4 03.04.36.062 Trigger valve spring 03.04.01.027 O-ring 1.7x2 03.04.31.116-01 Axle pin 03.04.02.128...
-
Page 24: Warranty
WARRANTY BENCHMARK WARRANTY If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 25 PNEUMATIC PIN NAILER *5 year limited warranty on tool 1282 206 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects in workmanship and materials.
Need help?
Do you have a question about the 1282 206 and is the answer not in the manual?
Questions and answers