Subscribe to Our Youtube Channel
Related Manuals for Benchmark 1282 151
Summary of Contents for Benchmark 1282 151
- Page 1 PNEUMATIC FRAMING NAILER 5 Year Limited Warranty READ ALL INSTRUCTIONS BEFORE FIRST USE. KEEP THIS MANUAL FOR FUTURE REFERENCE. KEEP AWAY FROM CHILDREN. WEAR CSA APPROVED WEAR EAR WEAR A EYE PROTECTION PROTECTION FACE MASK...
-
Page 2: Product Specifications
PRODUCT SPECIFICATIONS PNEUMATIC FRAMING NAILER Magazine capacity(QTY.) 80 PCS Drives Fastener Nail length: Clipped head nails: Nailer 50mm (2”)-90mm (3-1/2”) Working pressure 70-110 psi (4.8-7.5 bar) Maximum pressure 120 psi (8.3 bar) Average air consumption 5.8 CFM @ 90PSI Air inlet ¼”... -
Page 3: Table Of Contents
1282 151 PNEUMATIC FRAMING NAILER TABLE OF CONTENTS Product Specifications ................... 1 Table of Contents ................... 2 Safety Guidelines ..................3-6 Symbols ....................... 7 Tool Specific Warnings .................. 8 ............9 Know Your Pneumatic Framing Nailer ..............10-18 Assembly And Operating .................. -
Page 4: Safety Guidelines
SAFETY GUIDELINES WARNING: This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it thoroughly before using the product. The symbols listed below are used to indicate this information. DANGER! Potential hazard that will result in serious injury or loss of life. -
Page 5: Symbols
1282 151 PNEUMATIC FRAMING NAILER SYMBOL MEANING • Risk of inhalation: Never directly inhale the air produced by the compressor. • Risk of bursting: Do not adjust the pressure switch or safety valve for any reason. They have been pre-set at the factory for this compressor’s maximum pressure Tampering with the... - Page 6 WARNING! • Do not allow unskilled or untrained individuals to operate the air tool. • Do not use the tool for any task other than that it is designed to perform. • Locate the compressor in a well-ventilated area for cooling, and a minimum of 12”...
- Page 7 1282 151 PNEUMATIC FRAMING NAILER CAUTION! • Disconnect tool from the air supply and turn o the compressor before performing any maintenance or changing accessories, when clearing a jammed fastener, when the tool is not in use, when it is being handed to another person, and when it is left unattended.
-
Page 9: Tool Specific Warnings
1282 151 PNEUMATIC FRAMING NAILER TOOL SPECIFIC WARNINGS DANGER Potential hazard that will result in serious injury or death. • Do not disconnect or reconnect the air hose with the tool pressed or with a fastener in the guide. The tool may fire when it is reconnected to the air supply. -
Page 10: Know Your Pneumatic Framing Nailer
KNOW YOUR PNEUMATIC FRAMING NAILER Cylinder Cap Nailer body Trigger Mode selection switch Depth adjustment dial Spring loaded slide Magazine Air quick coupler... -
Page 11: Assembly And Operating
1282 151 PNEUMATIC FRAMING NAILER ASSEMBLY AND OPERATING COMPATIBLE COMPRESSORS GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with air-powered tools. The compressor should be able to supply a minimal air delivery of 5.8 SCFM @ 90 psi to ensure the compressor can run continuously with the tool. - Page 12 Air system Always use clean, dry, regulated, compressed air at 70-110 psi (4.8-7.5 bar). Do not exceed the maximum or minimum pressures. Operating the tool at the wrong pressure (too low or too high) will cause excessive noise or rapid wear of tool. No.
- Page 13 1282 151 PNEUMATIC FRAMING NAILER ACCEPTABLE NAILS This Pneumatic framing nailer drives 2 - 3 1/2" (50 to 90mm) long clipped-head framing nails. Length: 2 - 3 1/2" (50 to 90 mm) (Fig A) Angle: 34° (Fig B) 3.5” 2”...
- Page 14 OPERATING INSTRUCTIONS Features of the pneumatic framing nailer • This lightweight pneumatic framing nailer drives 2 to 3 1/2" (50 to 90 mm) long pneumatic framing nails. It features • – a hardened one-piece piston and an open magazine designed for easy extraction of jammed nails.
- Page 15 1282 151 PNEUMATIC FRAMING NAILER Insert a strip of nails into the magazine. Ensure the points of the nails are facing down. Be sure to insert the heads of the nails into the channel. Release the spring- loaded slide until it meets the nails and locks in place to close the magazine (1) (Fig.
- Page 16 Adjusting nail depth • For varying materials, the nail depth can be tool- free adjusted with the depth adjustment dial (Fig G) Note: Refer to the graphic imprinted below the trigger and adjust the firing depth accordingly. fig G Increasing nail depth Turn the depth adjustment dial (1) clockwise (with the discharge area of the tool facing away from the operator) (fig H).
- Page 17 1282 151 PNEUMATIC FRAMING NAILER SINGLE SEQUENTIAL ACTUATION MODE The single sequential actuation mechanism is for use where precise fastener placement is desired. The single sequential actuation mechanism may reduce the possibility of bodily injury to you or others in the work area compared to the contact/bump actuation mechanism.
- Page 18 WARNING! Potential hazard that could result in serious injury or loss of life. To avoid double firing or accidental firing due to recoil 1) Do not press the nailer against the wood with excessive force. 2) Separate the nailer from the wood as it recoils after nailing. WARNING! Potential hazard that could result in serious injury or loss of life.
- Page 19 1282 151 PNEUMATIC FRAMING NAILER STORAGE If it is necessary to store the tool for an extended period of time, apply a generous amount of lubrication before storing. The tool should be allowed to run for approximately 30 seconds after lubricating in order to ensure that the lubrication is...
-
Page 20: Maintenance
MAINTENANCE Note: Do not store the tool anywhere temperatures will fall below freezing. DANGER! Disconnect the tool from the air compressor before maintenance/service, adjusting, cleaning jams, reloading, and when it is not in use. Repairs must be performed by a qualified service technician only. Failure to comply will lead to serious injury or loss of life. -
Page 21: Troubleshooting
1282 151 PNEUMATIC FRAMING NAILER TROUBLESHOOTING DANGER! Potential hazard that will result in serious injury or loss of life. If any of the following symptoms appear while the tool is in use, turn it o and disconnect it from the air supply immediately. Failure to comply will lead to serious injury or loss of life. - Page 22 PROBLEM POSSIBLE CAUSES SOLUTIONS The tool jams. 1. Improper nails are used, or see section “Clearing a jammed nail.” nails are damaged. 1.Use the proper nail. 2. The driver guide is damaged 2.Inspect and replace the driver guide. or worn. 3.Tighten the magazine.
-
Page 23: Exploded View
1282 151 PNEUMATIC FRAMING NAILER EXPLODED VIEW... -
Page 24: Parts List
PARTS LIST WARNING: When servicing, use only original equipment replacement parts. The use of any other parts may create a safety hazard or cause damage to the tool. Any attempt to repair or replace electrical parts on this tool may create a safety hazard unless repairs are performed by a qualified technician. - Page 25 1282 151 PNEUMATIC FRAMING NAILER Key # Part # Part Name Quantity 03.04.05.056 Bolt M8x30 03.04.05.029 Bolt M5x14 03.04.05.263-03 Spring washer 5 03.04.05.256 Big washer 5 03.04.04.178 Nose protect cover 03.04.05.738-01 Nut M5 03.04.16.166 Safety shelf 03.04.05.237 Retaning ring 3 03.04.39.12.083...
- Page 26 Key # Part # Part Name Quantity 03.04.05.189 Pin 3x10 03.04.29.265 Gun body grip 03.04.19.038 End cover sealing washer 03.04.11.027-05 End cover 03.04.05.032 Bolt M5x20 03.04.40.170 Air inlet plug 03.04.29.158 Air inlet plug case 03.04.34.036-02 Spring A 03.04.22.021 Spring core 03.04.05.220 Pin 4x18 03.04.34.043...
-
Page 27: Warranty
WARRANTY BENCHMARK WARRANTY If this Benchmark tool fails due to a defect in material or workmanship within five years from the date of purchase, return it to any Home Hardware store with the original bill of sale for exchange. 3-year warranty for the battery and charger. This warranty does not include expendable parts including but not limited to blades, brushes, belts, light bulbs. - Page 28 PNEUMATIC FRAMING NAILER *5 year limited warranty on tool 1282 151 BENCHMARK TOOLS CANADA Made in China ST. JACOBS, ONTARIO N0B 2N0 © 2021 Home Hardware Stores Limited CUSTOMER SERVICE/TECH SUPPORT 1-866-349-8665 * This Benchmark product carries a five (5) year LIMITED warranty against defects in workmanship and materials.
Need help?
Do you have a question about the 1282 151 and is the answer not in the manual?
Questions and answers