Philips 32PFL3904H/12 Service Manual page 41

7.4 Front-End
The Front-End consist of the following key components:
• Tuner HD1816AF
• IF demodulator DRX3926K
• AGC amplifier UPC3221GV
• SAW filter 36M125.
Below find a block diagram of the front-end application.
SAW
NXP Hybrid
Filter
Tuner
I2C-TUNER
Figure 7-6 Front-End block diagram
The DRX3926K is a multi-standard demodulator supporting
DVB-C, DVB-T and analogue standards. The demodulated
digital stream is fed into the parallel transport stream data ports
of the PNX8543. The demodulated analogue signal in the form
of CVBS is connected to the analogue video CVBS/Y input
channel, while the SIF is connected via the SSIF2 positive input
port.
7.5 HDMI
In this platform, the TDA9996 HDMI multiplexer is
implemented. The EDID contents are no longer stored in a
separate EEPROM, but directly in the multiplexer. Each input
has its own physical sub address: the first 253 bytes are
common, where the last 3 bytes define the specific input. The
EDID contents are, at +5V power-up, downloaded to RAM. The
following figures show the HDMI input configuration and EDID
control.
PNX8543
A B
H D M IA-R X
E d id
H D M I 4
(optional)
1M 96
Figure 7-7 HDMI input configuration
I2C-SSB
CVBS
IF Amplifier DRX3926K PNX8543
2nd SIF
TS
IF-AGC
18440_211_090227.eps
H D M IB-R X
D R X
D
Out
H D M I Side
TDA9996
(optional)
C R X
AR X
B
BR X
H D M I 3
H D M I 2 H D M I 1
(optional)
18440_213_090227.eps
Circuit Descriptions
P la tfo rm w ith e m b e d d e d E D ID
Figure 7-8 EDID control (embedded EDID)
090227
Some delta's w.r.t. TDA9996 compared to earlier chassis/
platforms are:
• +5V detection mechanism
• stable clock detection mechanism
• integrated EDID
• RT control
• HPD control
• TMDS output control
• CEC control
• new hot-plug control for PNX8543 for 5th HDMI input
• new EDID structure: EDID stored in TDA9996, therefore
there are no EDID pins on the SSB. Only in the event of a
5th HDMI input, an additional EEPROM is foreseen, as
was implemented in previous platforms.
Some delta's with respect to PNX8543 compared to earlier
chassis/platforms are:
• 2 HDMI inputs (A & B)
• HDMI deep colour RGB/YCbCr 4:4:1 10/12 bit detection.
After replacement of the TDA9996 HDMI multiplexer, the
2
default I
and the HDMI EDIDs should be reprogrammed as well. Both
actions should be executed via ComPair.
090720
Q543.1E LA
2
E D ID : 2 5 3 B
I C
TDA9996
3B 3B 3B 3B
2 5 3 co m m o n B yte s
+ 1B su b a d d re s o f
S o u rce P h ysica l A d d re ss
+3B fo r inp u t A
+3B fo r inp u t B
4 × H D M I
+3B fo r inp u t C
inputs
+3B fo r inp u t D
C address should be reprogrammed from C0 to CE,
7. EN 41
CPU
18440_214_090227.eps
090720
2009-Nov-20