Related Manuals for IFM Electronic CR1083
Summary of Contents for IFM Electronic CR1083
- Page 1 Installation instructions Process and dialogue module PDM360 NG CR1083 CR9225 CR1087...
-
Page 2: Table Of Contents
5�5�1 Ethernet cameras� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 16 5�6 Analogue video inputs (only CR1083) � � � � � � � � � � � � � � � � � � � � � � � � � � � 16 5�7 USB interfaces �... - Page 3 7�1 CR1083 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �...
-
Page 4: Preliminary Note
1 Preliminary note This document applies to devices of the type "PDM360 NG" (article numbers CR1083 and CR1087)� These instructions are part of the device� This document is intended for specialists� These specialists are people who are qualified by their appropriate training and their experience to see risks and to avoid possible hazards that may be caused during operation or maintenance of the device�... -
Page 5: Safety Instructions
PDM360 NG process and dialogue module (CR1083/87) 2 Safety instructions 2.1 General These instructions contain texts and figures concerning the correct handling of the device and must be read before installation or use� Observe the operating instructions� Non-observance of the instructions, operation which is not in accordance with use as prescribed below, wrong installation or incorrect handling can seriously affect the safety of operators and machinery�... -
Page 6: Functions And Features
PDM360 NG process and dialogue module (CR1083/87) 3 Functions and features The PDM360 NG process and dialogue module is a programmable graphic display for controlling, parameter-setting and operation of mobile machines and plants� Communication with other system components, e�g� decentralised I/O modules, is handled via a CAN interface using the CANopen protocol�... -
Page 7: 3�2 Overview Of The Common Characteristics
PDM360 NG process and dialogue module (CR1083/87) 3.2 Overview of the common characteristics ● 7" Colour display ● Programmable backlit function keys ● Closed metal housing suitable for panel mounting and surface mounting outside or in the cabin ● Freely programmable to IEC 61131-3 with target visualisation ●... -
Page 8: Installation
® You can find more information about the available accessories at: www.ifm.com → data sheet search → e.g. CR1083 → Accessories 4.2 General installation instructions 4.2.1 Locator for mounting accessories The back of the unit has been prepared for fixing the mounting accessories�... -
Page 9: 4�2�2 Orientation Of The Device With Panel And Surface Mounting
PDM360 NG process and dialogue module (CR1083/87) 4.2.2 Orientation of the device with panel and surface mounting Horizontal orientation for panel and surface mounting 4.2.3 Light sensor The device is equipped with a light sensor� It is used for automatic brightness adaptation of the display and the operating elements to the ambient brightness�... -
Page 10: 4�3 Panel Mounting Using The Mounting Frame
PDM360 NG process and dialogue module (CR1083/87) 4.3 Panel mounting using the mounting frame The mounting frame ensures horizontal, vertical or up-side down mounting of the device in a panel cutout� This type of mounting is suited for materials with a thickness from 1 to 10 mm�... -
Page 11: 4�3�1 Mounting Steps
PDM360 NG process and dialogue module (CR1083/87) 4.3.1 Mounting steps Mounting principle Installation depth A: approx� 60���65 mm (depending on the panel thickness and the length of 1: mounting frame with M5 hexagon nuts (self- the set screws, without connector) - Page 12 PDM360 NG process and dialogue module (CR1083/87) Attached seal Removed sides ► Screw the set screws into the M5 thread on the back of the device� (→ 4.2.1 Locator for mounting accessories) Select the set screws in accordance with the panel thickness�...
-
Page 13: 4�4 Surface Mounting With Ram
► Slightly loosen the fastening screw of the mounting arm� ► Place the mounting arm onto the balls and tighten the fastening screw� You can find more information about the available RAM mount components at: ® www.ifm.com → data sheet search → e.g. CR1083 → Accessories... -
Page 14: Electrical Connection
5 Electrical connection 5.1 Connection accessories You can find more information about the available accessories at: www.ifm.com → data sheet search → e.g. CR1083 → Accessories www.ifm.com → Products → Accessories → Connection technology 5.2 General electrical connection Wiring of the M12 connectors (→ 7 Technical data) -
Page 15: 5�3 Operating Voltage And Fuses
PDM360 NG process and dialogue module (CR1083/87) 5.3 Operating voltage and fuses ► To protect the device use fuses for the operating voltages� Description Potential Connector 1 Fuse Operating voltage 10…32 V DC pin 1 max� 5 A clamp 30... -
Page 16: 5�5 Ethernet Interface
PDM360 NG process and dialogue module (CR1083/87) To avoid contact corrosion on the shield connection of the device, do not use any copper or nickel-plated materials for the bolting elements! ► In very corrosive environments such as extremely salty air, use screws with surface finishing on a zinc/nickel basis with thick-film passivation and sealing�... -
Page 17: 5�7 Usb Interfaces
PDM360 NG process and dialogue module (CR1083/87) 5.7 USB interfaces The USB interfaces are used for the temporary connection of an external keyboard, a mouse or a USB memory stick� They are not intended for actual operation� ► Remove the USB devices after their use�... -
Page 18: 5�7�2 Short-Circuit Protection
PDM360 NG process and dialogue module (CR1083/87) 5.7.2 Short-circuit protection NOTE The USB interface (M12 connector) is not protected against short circuits with a live wire outside the following voltage ranges: –data 0�3���3�6 V DC (3: pin 2) +data 0�3���3�6 V DC (3: pin 3) 0�3���3�6 V DC... -
Page 19: Set-Up
PDM360 NG process and dialogue module (CR1083/87) 6 Set-up 6.1 General As delivered the device is prepared for programming with CODESYS version 2�3 or higher� Factory setting: IP address: 192�168�82�247 Subnet mask: 255�255�255�0 The user is responsible for the safe function of the application programs which he created himself�... -
Page 20: 6�4 Required Documentation
● PDM360 NG system manual (alternatively as online help) The manuals can be downloaded from the internet: www.ifm.com → data sheet search → e.g. CR1083 → Additional data CODESYS and PDM360 NG online help: www.ifm.com → Service → Download → Control systems*... -
Page 21: Technical Data
IP 67 (with mounted connectors and/or protective caps) Operating temperature -30���65° C Storage temperature -30���80° C Weight approx� 1�5 kg ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1083 / page 1 12�01�2018... - Page 22 Characteristics of the output Switching voltage 10���32 V DC Switching current ≤ 1 A Free-wheeling diodes integrated ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1083 / page 2 12�01�2018...
- Page 23 5 Hz boot process system recovery/update 2 Hz system recovery/update running briefl y on System reset ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1083 / page 3 12�01�2018...
- Page 24 EN 50155 clause 12�2 mechanical/climatic tests EN 50121-3-2 EMC noise emission and noise immunity additional information on request ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1083 / page 4 12�01�2018...
- Page 25 (8) N/A Shield GND (video 2) GND (video 1) FBAS1 (video 1) FBAS2 (video 2) ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1083 / page 5 12�01�2018...
-
Page 26: 7�2 Cr1087
IP 67 (with mounted connectors and/or protective caps) Operating temperature -30���65° C Storage temperature -30���80° C Weight approx� 1�5 kg ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1087 / page 1 12�01�2018... - Page 27 Embedded Linux 2�6 Programming system CoDeSys version 2�3 (IEC 61131-3) Graphic functions via integrated target visualisation ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1087 / page 2 12�01�2018...
- Page 28 5 Hz boot process system recovery/update 2 Hz system recovery/update running briefl y on System reset ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1087 / page 3 12�01�2018...
- Page 29 EN 50155 clause 12�2 mechanical/climatic tests EN 50121-3-2 EMC noise emission and noise immunity additional information on request ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1087 / page 4 12�01�2018...
- Page 30 CAN3_H (OUT) CAN3_L CAN2_GND (OUT) CAN3/4_GND (OUT) CAN2_H CAN4_H CAN2_L CAN4_L (7) N/A (8) N/A ifm electronic gmbh • Friedrichstraße 1 • 45128 Essen We reserve the right to make technical alterations without prior notice! CR1087 / page 5 12�01�2018...
-
Page 31: Maintenance, Repair And Disposal
PDM360 NG process and dialogue module (CR1083/87) 8 Maintenance, repair and disposal 8.1 Battery change 1: service cover 1: battery cover 2: socket head screws 2: indentation for opening 3: battery case ► Remove the service cover on the back of the unit�... -
Page 32: 8�3 Cleaning The Housing Surface
► Dispose of the device in accordance with the national environmental regulations� 9 Approvals / standards Test standards and regulations (→ 7 Technical data) The EC declaration of conformity and approvals can be found at: www.ifm.com → data sheet search → e.g. CR1083 → Approvals...
Need help?
Do you have a question about the CR1083 and is the answer not in the manual?
Questions and answers