Page 1
DIGITAL CAMERA Reference Guide • Read this document thoroughly before using the camera. • To ensure proper use of the camera, be sure to read “For Your Safety” (page 27). • After reading this document, keep it readily accessible for future reference.
When Your First Photo Can’t Wait Getting Ready Insert the battery ( 80). For information on charging the battery, see “Charging the Battery” ( 75). Insert a memory card ( 82). Attach a lens ( 85). Align the mounting mark on the lens with the matching mark on the camera body (q) and rotate the lens in the direction shown (w).
Taking and Viewing Pictures To focus, press the shutter-release button halfway (i.e., lightly press the shutter-release button, stopping when it is pressed halfway; 89). Without lifting your finger from the shutter-release button, press the button the rest of the way down to take the picture.
MH‑25a battery chargers are sold separately in some countries or regions. The Nikon Download Center Visit the Nikon Download Center to download firmware updates, NX Studio and other Nikon software, and documentation for Nikon products including cameras, NIKKOR lenses, and flash units.
About This Document Symbols This document employs the following symbols. Use them to help locate the information you need. This icon marks notes, information that should be read before using this product. This icon marks tips, additional information you may find helpful when using this product. This icon marks references to other sections in this document.
For Your Safety To prevent damage to property or injury to yourself or to others, read “For Your Safety” in its entirety before using this product. After reading these safety instructions, keep them readily accessible for future reference. DANGER: Failure to observe the precautions marked with this icon carries a high risk of death or severe injury.
Page 28
WARNING Do not use this product in the presence of flammable dust or gas such as propane, gasoline or aerosols. Failure to observe this precaution could result in explosion or fire. Do not directly view the sun or other bright light source through the lens. Failure to observe this precaution could result in visual impairment.
Page 29
CAUTION Do not leave the lens pointed at the sun or other strong light sources. Light focused by the lens could cause fire or damage to product’s internal parts. When shooting backlit subjects, keep the sun well out of the frame. Sunlight focused into the camera when the sun is close to the frame could cause fire.
Page 30
DANGER (Batteries) Do not mishandle batteries. Failure to observe the following precautions could result in the batteries leaking, overheating, rupturing, or catching fire: Use only rechargeable batteries approved for use in this product. Do not expose batteries to flame or excessive heat. Do not disassemble.
Page 31
WARNING (Batteries) Discontinue use immediately should you notice any changes in the batteries, such as discoloration or deformation. Cease charging EN‑EL15c rechargeable batteries if they do not charge in the specified period of time. Failure to observe these precautions could result in the batteries leaking, overheating, rupturing, or catching fire.
Nikon will not be held liable for any damages resulting from the use of this product. While every effort has been made to ensure that the information in this documentation is accurate and complete, we would appreciate it were you to bring any errors or omissions to the attention of the Nikon representative in your area (address provided separately).
Page 33
Nikon cameras include complex electronic circuitry. Only Nikon brand electronic accessories (including lenses, chargers, batteries, AC adapters, and flash accessories) certified by Nikon specifically for use with this Nikon digital camera are engineered and proven to operate within the operational and safety requirements of this electronic circuitry.
Page 34
Before taking pictures on important occasions (such as at weddings or before taking the camera on a trip), take a test shot to ensure that the camera is functioning normally. Nikon will not be held liable for damages or lost profits that may result from product malfunction.
Parts of the Camera Camera Body BKT button (D; 162) Exposure compensation button (E; 131) WB button (U; 143) Eyelet for camera strap ( Stereo microphone ( Speaker Video-record button ( Focal plane mark (E; 120) Power switch ( Control panel ( ...
Page 38
Diopter adjustment control ( OK button (J; DISP button (d; Multi selector ( Photo/video selector ( Playback zoom in button (X; 119, AF-ON button (B; 118) 212, 233) Sub-selector ( 114, 117, 129) MENU button (G; Main command dial Playback button (K;...
Page 39
Lens release button ( Battery chamber cover latch Lens mount ( 120) Memory card slot cover ( CPU contacts Fn2 button (k; Image sensor ( 895) Fn1 button (j; Tripod socket Sub-command dial Battery chamber cover Do Not Touch the Image Sensor or Sensor Shield Under no circumstances should you poke or exert pressure on the image sensor or sensor shield 728) or subject them to powerful air currents from a blower.
Page 40
Tip: Notes on the Monitor The angle of the monitor can be adjusted. Tip: Product Serial Number The serial number for this product can be found by opening the monitor. Tip: The LCD Illuminator Rotating the power switch to D activates the backlights for the buttons and control panels (LCD illuminator).
The Control Panel The control panel lights when the camera is on. At default settings, the following indicators are displayed. For a full list of the indicators that may be displayed, see “The Control Panel” ( 827) in the section on “Camera Displays” in the “Technical Notes” chapter. Shooting mode ( 121) ISO sensitivity indicator (...
The Monitor At default settings, the following indicators appear in the monitor. For a full list of the indicators that may be displayed, see “The Monitor” in the section on “Camera Displays” ( 817) in the “Technical Notes” chapter. Photo Mode 2 3 4 6 7 8 Shooting mode (...
Page 44
Tip: Using the Monitor with the Camera in “Tall” Orientation In photo mode, the playback, i menu, and shooting displays rotate to match camera orientation. Tip: Choosing a Display Press the DISP button to cycle the shooting display. Choose from up to five displays, each with a customizable selection of icons and indicators.
The Viewfinder At default settings, the following indicators appear in the viewfinder. For a full list of the indicators that may be displayed, see “The Viewfinder” in the section on “Camera Displays” ( 824) in the “Technical Notes” chapter. Photo Mode 7 8 9 View mode (photo live view;...
Page 47
Battery indicator ( Aperture ( 122, 123) Number of exposures remaining ( Shutter speed ( 122, 123) 922) Shooting mode ( 121) ISO sensitivity ( 139) Vibration reduction indicator ( 470) ISO sensitivity indicator ( 139) Metering ( 461) Auto ISO sensitivity indicator ( 141) Focus point ( 114)
Page 48
Tip: Using the Viewfinder with the Camera in “Tall” Orientation In photo mode, the playback, i menu, and shooting displays rotate to match camera orientation. Tip: Choosing a Display Press the DISP button to cycle the shooting display. Choose from up to four displays, each with a customizable selection of icons and indicators.
Video Mode Recording indicator Image area ( 200) “No video” indicator ( Video file type ( 190) Length of footage recorded Recording indicator (red border; 687) Destination ( 515) Sound level ( 541) Available recording time Microphone sensitivity ( 541) Frame size and rate ( 193) The Viewfinder...
Tip: Using the Viewfinder with the Camera in “Tall” Orientation In video mode, the playback and playback i menu displays rotate to match camera orientation. The Monitor Mode Button and the Eye Sensor Placing your eye to the viewfinder activates the eye sensor, switching the display from the monitor to the viewfinder.
Page 51
Press the M button to cycle through the displays as follows. [Automatic display switch]: The camera automatically switches between the viewfinder and monitor displays based on information from the eye sensor. [Viewfinder only]: The monitor remains blank. The viewfinder is used for shooting, menus, and playback.
Page 52
[Prioritize viewfinder (1)]: In photo mode, the camera functions in a manner similar to existing digital SLR cameras. Placing your eye to the viewfinder turns the viewfinder on; the monitor remains off after you take your eye away. In video mode, the displays function as per [Automatic display switch].
Page 53
The Diopter Adjustment Control The viewfinder can be focused by lifting and rotating the diopter adjustment control. Be careful not to put your fingers or fingernails in your eye. After adjusting diopter, push the diopter adjustment control back into its original position. Tilting the Monitor Putting your eye to the camera when the monitor is tilted will not trigger the viewfinder if both the following conditions are met:...
Touch Controls The touch-sensitive monitor offers a variety of controls that can be operated by touching the display with your fingers. During viewfinder photography, touch controls are disabled and cannot be used for focus or the like. Focusing and Releasing the Shutter Touch the monitor to focus on the selected point (touch AF).
Adjusting Settings Tap highlighted settings in the display. You can then choose the desired option by tapping icons or sliders. Tap Z or press J to select the chosen option and return to the previous display. Touch Controls...
Playback Flick left or right to view other pictures during full-frame playback. In full-frame playback, touching the bottom of the display brings up a frame-advance bar. Slide your finger left or right over the bar to scroll rapidly to other pictures. To zoom in on a picture displayed during full-frame playback, use a stretch gesture or give the display two quick taps.
Viewing Videos Videos are indicated by a 1 icon; to start playback, tap the a icon. Tap Z to exit to full-frame playback. The i Menu Tap the i icon to display the i menu during shooting ( 68). Tap items to view and change options. You can choose the items displayed in the i menu ( 73).
Text Entry When a keyboard is displayed, you can enter text by tapping the keys. Text display area Keyboard area Keyboard selection To position the cursor, tap e or f or tap directly in the text display area. To cycle through the upper- and lower-case and symbol keyboards, tap the keyboard selection button.
Navigating the Menus Slide up or down to scroll. Tap a menu icon to choose a menu. Tap menu items to display options. You can then choose the desired option by tapping icons or sliders. To exit without changing settings, tap Z. Touch Controls...
Page 60
Cautions: The Touch Screen The touch screen responds to static electricity. It may not respond when touched with fingernails or gloved hands. For improved response when using the touch screen with gloves, select [ON] for [Touch controls] > [Glove mode] in the setup menu. Do not touch the screen with sharp objects.
The Fn1 and Fn2 Buttons Use the Fn1 or Fn2 button for quick access to selected settings during shooting. By default, the Fn1 button is used to choose the shooting menu bank ( 421) and the Fn2 button, the image area ( 99).
Using the Menus The MENU Button Press the G button to view the menus. C PHOTO SHOOTING MENU ( 418) 1 VIDEO RECORDING MENU ( 509) A CUSTOM SETTINGS MENU ( 551) D PLAYBACK MENU ( 688) B SETUP MENU ( 707) F NETWORK MENU ( 764) * O MY MENU/m RECENT SETTINGS...
Using the Menus You can navigate the menus using the multi selector and J button. Move cursor up Select the highlighted item Display sub-menu, select highlighted item, or move cursor right Move cursor down Cancel and return to previous menu, or move cursor left Highlight the icon for the current menu.
Page 64
Position the cursor in the selected menu. Press 2 to position the cursor in the selected menu. Highlight a menu item. Press 1 or 3 to highlight a menu item. Display options. Press 2 to display options for the selected menu item. The MENU Button...
Page 65
Highlight an option. Press 1 or 3 to highlight an option. Select the highlighted option. Press J to save changes and exit. To exit without making a selection, press the G button. To exit the menus and return to shooting mode, press the shutter- release button halfway.
Page 66
Grayed-Out Items Some items and menu options may be unavailable depending on camera status. Unavailable items are displayed in gray. In some cases, pressing J when a grayed-out item is highlighted will display a message explaining why the item is unavailable. Tip: ON/OFF Only Items If the only options available for the current item are [ON] and [OFF], you can switch from [ON] to [OFF] or vice versa simply by pressing...
Page 67
Tip: Touch Controls You can also navigate the menus using touch controls ( 54). Tip: Text Entry A keyboard is displayed when text entry is required, for example if you are called on to enter a file name or the like. Enter text as described below. Text display area Keyboard area Keyboard selection...
The i Button (i Menu) For quick access to frequently-used settings, press the i button or tap the i icon to view the i menu. Different menus are displayed in photo and video modes. Options can be viewed by tapping items in the display or by highlighting items and pressing J;...
Page 69
Tip: Using the i Menu with the Camera in “Tall” Orientation When the camera is rotated to take or view pictures in “tall” (portrait) orientation in photo mode, the i menu displays in the monitor and viewfinder rotate to match. In video mode, only the playback i menu rotates to match camera orientation.
The Still Photography i Menu Pressing the i button in photo mode displays the items listed below. Highlight the desired item using the multi selector and press J to view options. Set Picture Control ( 175) Tone mode ( 433) White balance ( 143) Vibration reduction (...
The Video i Menu Pressing the i button in video mode displays the items listed below. Highlight the desired item using the multi selector and press J to view options. Set Picture Control ( 175) Focus mode ( 105) White balance ( 143) Electronic VR ( 540)
The Playback i Menu Pressing the i button during playback displays a context-sensitive i menu of playback options. Photos Videos Videos (playback paused) The i Button (i Menu)
Customizing the i Menu The items displayed in the i menu during shooting can be chosen using Custom Setting f1 or g1 [Customize i menu]. Highlight Custom Setting f1 or g1 [Customize i menu] and press J. See “The G Button” ( 62) for information on using the menus.
Charging the Battery Charge the supplied EN‑EL15c battery before use. Caution: The Battery and Charger Read and follow the warnings and cautions in “For Your Safety” ( 27) and “Caring for the Camera and Battery: Cautions” ( 899). The Battery Charger Depending on the country or region, the charger comes with either an AC wall adapter or a power cable.
Page 76
The ambient temperature is too hot or too cold: Use the battery charger at temperatures within the designated temperature range (0–40 °C/+32–104 °F). If the problem persists, unplug the charger and end charging. Bring the battery and charger to a Nikon-authorized service representative. Charging the Battery...
Optional EH‑7P Charging AC Adapters/EH‑8P AC Adapters: Charging When inserted in the camera, the battery can be charged using an optional EH‑7P charging AC adapter or EH‑8P AC adapter. An exhausted battery will fully charge in about 2 hours and 40 minutes. When charging is complete, unplug the EH‑7P or EH‑8P and disconnect it from the camera.
Page 78
Using the EH‑8P AC Adapter Connect an optional UC‑E25 USB cable (featuring Type C connectors at both ends) to the EH‑8P AC adapter (q). After confirming that the camera is off, connect the other end of the cable to the camera’s USB Power Delivery connector (w) and plug the adapter in.
Page 79
Cautions: The EH‑7P/EH‑8P The battery will not charge if the cable is connected to the camera’s USB data connector. The EH‑7P and EH‑8P can be used only with EN‑EL15c and EN‑EL15b batteries. EN‑EL15a batteries can be charged using an MH‑25a battery charger. Charging errors caused by, for example, elevated camera temperatures or attempts to charge an EN‑EL15a are indicated by the charge lamp flashing rapidly for about 30 seconds before turning off.
Inserting the Battery Turn the camera off before inserting or removing the battery. Using the battery to keep the orange battery latch pressed to one side, slide the battery into the battery chamber until the latch locks it in place. Removing the Battery To remove the battery, turn the camera off and open the battery chamber cover.
Battery Level The battery level is shown in the shooting display and control panel while the camera is on. Control panel Monitor Viewfinder The battery level display changes as the battery level diminishes, from L through K, J, I, and H.
Inserting Memory Cards The camera is equipped with two memory card slots: a slot that takes one CFexpress or XQD memory card (q) and another that takes one SD memory card (w), for a total of two cards, one of each type.
Page 83
Tip: Number of Exposures Remaining The shooting display and control panel show the number of photographs that can be taken at current settings. Values over 1000 are rounded down to the nearest hundred. For example, values between 8000 and 8099 are shown as 8.0 k. If no memory cards are inserted, an [–E–] indicator will be displayed.
Removing Memory Cards After confirming that the memory card access lamp is off, turn the camera off, open the memory card slot cover, and press the card in to eject it (q). The card can then be removed by hand (w). Memory Card High-Temperature Warning As indicated in the label inside the memory card slot cover, memory cards may become hot while inserted in the camera.
The camera can be used with Z mount lenses. For more information on lenses, see the lens documentation available from the Nikon Download Center. The lens generally used in this document for illustrative purposes is a NIKKOR Z 50mm f/1.8 S.
Rotate the lens as shown until it clicks into place (u). Remove the front lens cap before taking pictures. F Mount Lenses Be sure to attach an FTZ II or FTZ mount adapter (available separately) to the camera before using F mount lenses ( 865).
Camera Setup Turn the camera on, choose a language, and set the clock. Before using the camera for the first time, follow the steps below to choose a language and time zone and set the clock so that the correct time and date will be recorded with any pictures you take.
Page 88
Turn daylight saving time on or off. Select [Daylight saving time] in the [Time zone and date] display. Select [ON] (daylight saving time on) or [OFF] (daylight saving time off). Selecting [ON] advances the clock one hour; to undo the effect, select [OFF].
Basic Photography and Playback Taking Photographs The basic steps involved in taking photographs are described below. Lenses with Retractable Barrels Lenses with retractable barrels must be extended before use. Rotate the zoom ring as shown until the lens clicks into place in the extended position.
Page 90
Frame the photograph. Position the main subject near the center of the frame. To focus, press the shutter-release button halfway (i.e., lightly press the shutter-release button, stopping when it is pressed halfway). The focus point will be displayed in green when the subject is in focus.
Page 91
The Memory Card Access Lamp The memory card access lamp will light while the photograph is being recorded. Do not remove the memory card or battery. Tip: The Touch Shutter You can also take a photograph by touching the monitor. Touch your subject to focus and lift your finger to release the shutter 115).
Recording Videos The basic steps involved in recording videos are described below. Select video mode by rotating the photo/video selector to Note that optional flash units cannot be used when the camera is in video mode. Press the video-record button to start recording. A recording indicator will be displayed and the borders of the shooting display will turn red.
Page 93
The camera can be refocused during recording by pressing the AF-ON button. Sound is recorded via the built-in microphone. Do not cover the microphone during recording. You can also focus by tapping your subject in the monitor. Press the video-record button again to end recording. The Memory Card Access Lamp The memory card access lamp will light while the video is being recorded.
Page 94
High-Temperature Warnings During video recording, the camera or memory cards may become hot and a high-temperature warning or memory card high- temperature warning may appear in the shooting display. Wait for the camera to cool and the warnings to clear from the display before handling the camera, battery, or memory cards.
Playback Press the K button to view photos and videos in the monitor or viewfinder after shooting. Press 4 or 2 or flick left or right to view additional pictures. Videos are indicated by a 1 icon at the top left corner of the display.
Viewing Videos The video playback display and controls are described below. The Video Playback Display During video playback, the display shows the length of the video, the current playback position, and the other indicators listed below. Your approximate position in the video can also be ascertained from the video progress bar.
Page 97
Video Playback Controls The following operations can be performed while playback is in progress: Operation Description Pause Press 3 to pause playback. Press the J button to resume playback when playback is paused or during Resume rewind/advance. Press 4 to rewind, 2 to advance. Speed increases with each press, from 2× Rewind/advance to 4×...
Deleting Unwanted Pictures Press the O (Q) button to delete the current picture. Note that pictures cannot be recovered once deleted. Display a picture you want to delete and press the O (Q) button to display a confirmation dialog. Press the O (Q) button again to delete the picture and return to playback.
Shooting Settings Image Recording Options (Image Area, Quality, and Size) Adjusting Image Area Settings At default settings, image area can be selected by holding the Fn2 button and rotating a command dial. Image area settings can be displayed by selecting [Image area] in the photo shooting menu.
Page 100
Choose Image Area Choose the image area. The following options are available: Option Description Record pictures in FX format with an angle of view equivalent to a 35 mm [FX (36×24)] format camera. Pictures are recorded in DX format. To calculate the approximate focal length [DX (24×16)] of the lens in 35 mm format, multiply by 1.5.
Adjusting Image Quality Choose the image quality option used when photographs are recorded. Choosing an Image Quality Option Image quality can be adjusted using the [Image quality] item in the photo shooting menu. Option Description Record two copies of each photo: an NEF (RAW) picture and either [RAW + JPEG/HEIF finem] a JPEG or HEIF copy.
Page 102
NEF (RAW) processing can be performed using [Retouch] > [RAW processing (current picture)] or [RAW processing (multiple pictures)] in the playback i menu or on a computer using Nikon’s NX Studio software. NX Studio is available free-of-charge from the Nikon Download Center.
Choosing an Image Size Use [Image size settings] in the photo shooting menu to choose a size for new photographs. Image Size Choose a size for new JPEG and HEIF pictures. The size for JPEG and HEIF pictures can be selected from [Large], [Medium], and [Small]. NEF (RAW) pictures are recorded at a size of [Large].
Page 104
Image area Image size Size when printed at 300 dpi Large (8256 × 4640 pixels) Approx. 69.9 × 39.3cm/27.5 × 15.5 in. [16:9 (36×20)] Medium (6192 × 3480 pixels) Approx. 52.4 × 29.5 cm/20.6 × 11.6 in. Small (4128 × 2320 pixels) Approx. 35.0 × 19.6 cm/13.8 × 7.7 in. Tip: Print Size Print size in inches equals image size in pixels divided by printer resolution in dots per inch (dpi; 1 inch = 2.54 cm).
Focus Focus Mode Control how the camera focuses. Choosing a Focus Mode The focus mode can be selected by holding the focus-mode button and rotating the main command dial. Tip: “Focus Mode” The focus mode can also be selected using the [Focus mode] items in the photo shooting and video recording menus.
Page 106
Option Description The camera adjusts focus continuously in response to subject movement or changes in composition. AF‑F [Full-time AF] When you press the shutter-release button halfway to focus, the focus point will turn from red to green and focus will lock. This option is only available in video mode.
AF-Area Mode Choose how the camera selects the focus point for autofocus. In modes other than [Auto-area AF], the focus point can be positioned using the sub-selector or multi selector ( 114) . Choosing an AF-Area Mode To choose the AF-area mode, hold the focus-mode button and rotate the sub-command dial. Tip: “AF-Area Mode”...
Page 108
Option Description [Dynamic- The camera focuses on a point selected by the user. If the subject briefly area AF (S)] leaves the selected point, the camera will focus based on information from surrounding focus points. [Dynamic- This option is only available when photo mode is selected and area AF [Continuous AF] is chosen for focus mode.
Page 109
Option Description The camera tracks focus on a selected subject. Position the focus point over your subject and start tracking by pressing AF‑ON or by pressing the shutter-release button halfway; focus will then track the selected subject as it moves through the frame. Release the [3D- button to end tracking and restore the previously-selected focus point.
Page 110
Caution: 3D-Tracking and Subject Tracking The camera may be unable to track subjects that: are similar in color, brightness, or pattern to the background, change visibly in size, color, or brightness, are too large or too small, too bright or too dark, move quickly, or are obscured by other objects or leave the frame.
Choosing a Subject Type for Autofocus The class of subjects given priority during autofocus can be chosen using the [AF subject detection options] items in the photo shooting and video recording menus, which offer a choice of [Auto], [People], [Animal], [Vehicle], [Airplanes], and [Subject detection off].
Page 112
If an aircraft is detected when [Airplanes] is selected, the focus point will appear over the aircraft in question. The camera will detect the body, nose, or cockpit depending on the aircraft’s size. If [Auto] is selected, the camera will detect humans, animals, and vehicles and choose a subject for focus automatically.
Page 113
Caution: Face/Eye-Detection AF Subject detection may not perform as expected if: the subject’s face is too large or small relative to the frame, the subject’s face is too brightly or dimly lit, the subject is wearing glasses or sunglasses, the subject’s face or eyes are obscured by hair or other objects, or the subject moves excessively during shooting.
Focus-Point Selection Except when [Auto-area AF] is selected for AF-area mode, the focus point can be selected manually, allowing photographs to be composed with the subject positioned almost anywhere in the frame. Use the multi selector to select the focus point while the standby timer is on. Pressing J selects the center focus point.
The Touch Shutter Touch the display to focus on the selected point. The shutter will be released when you lift your finger from the display. Tap the icon shown in the illustration to choose the operation performed by tapping the display. Option Description Touch the display to focus on the selected point and lift your finger to...
Page 116
Cautions: Taking Pictures Using Touch Shooting Options Touch controls cannot be used for manual focus. The shutter-release button can be used to take pictures when the W icon is displayed. During burst photography, touch controls can be used only to take one picture at a time. Use the shutter-release button for burst photography.
Focus Lock Use focus lock in cases in which the camera has trouble focusing with autofocus. Use focus lock to lock focus on the current subject when AF‑C is selected for focus mode. When using focus lock, choose an AF-area mode other than [Auto-area AF]. Position the subject in the selected focus point and press the shutter-release button halfway.
Page 118
Locking Focus When AF-S Is Selected for Focus Mode Focus locks while the shutter-release button is pressed halfway. You can also lock focus by pressing the center of the sub-selector. Taking Multiple Shots at the Same Focus Distance If you locked focus by pressing the center of the sub-selector, focus will remain locked between shots if you keep the center of the sub-selector pressed.
Manual Focus Manual focus is available in manual focus mode. Use manual focus when, for example, autofocus does not produce the desired results. Position the focus point over your subject and rotate the focus or control ring until the subject is in focus. For greater precision, press the X button to zoom in on the view through the lens.
Page 120
Focus indicator Description Focus is behind the subject. (steady) The camera is unable to focus. (flashes) When using manual focus with subjects not suited to autofocus, note that the in-focus indicator (I) may be displayed when the subject is not in focus. Zoom in on the view through the lens and check focus.
Exposure Choosing a Shooting Mode To choose a shooting mode, hold the I button and rotate the main command dial. The selected option is shown in the shooting display and control panel. Mode Description Use for snapshots and in other situations in which there is Programmed auto ( 122) little time to adjust camera settings.
Page 122
P (Programmed Auto) In this mode, the camera automatically adjusts shutter speed and aperture according to a built-in program to ensure optimal exposure in most situations. Different combinations of shutter speed and aperture that produce the same exposure can be selected by rotating the main command dial (“flexible program”).
Page 123
M (Manual) You control both shutter speed and aperture. Choose this mode for long time-exposures of such subjects as fireworks or the night sky (“Bulb” or “Time” photography, 126). Shutter speed and aperture can be adjusted with reference to the exposure indicators by rotating the command dials.
Page 124
Exposure Indicators The exposure indicators in the monitor, viewfinder, and control panel show whether the photograph would be under- or over-exposed at current settings. The exposure indicators can be read as follows (the display varies with the option selected for Custom Setting b2 [EV steps for exposure cntrl]): [1/3 step] selected for [EV steps for exposure cntrl] Display Optimal exposure...
Page 125
Tip: Extended Shutter Speeds For shutter speeds as slow as 900 s (15 minutes), select [ON] for Custom Setting d5 [Extended shutter speeds (M)]. Tip: Long Exposures At speeds slower than 1 s, the shutter speed displayed by the camera may differ from the actual exposure time.
Long Time-Exposures (Mode M Only) The camera offers two options for long time-exposures: “Bulb” and “Time”. Long time-exposures can be used for pictures of fireworks, night scenery, the stars, or moving lights. A 35-second exposure shot at a shutter speed of “Bulb” and an aperture of f/25 Shutter speed Description Bulb...
Page 127
Rotate the main command dial to choose a shutter speed of Bulb (“Bulb”) or Time (“Time”). Bulb Time Note that the exposure indicators are not displayed at a shutter speed of Bulb or Time. Focus and start the exposure. “Bulb”: Press the shutter-release button all the way down to start the exposure. Keep the shutter-release button pressed during the exposure.
Page 128
Long Time-Exposures Note that “noise” (bright spots, randomly-spaced bright pixels or fog) may be present in long exposures. Bright spots and fog can be reduced by choosing [ON] for [Long exposure NR] in the photo shooting menu. We recommend using one of the following power sources to prevent loss of power during long exposures: A fully-charged battery An optional EH‑7P charging AC adapter...
Autoexposure Lock Use autoexposure lock to recompose photographs after setting exposure for a specific area of the subject. Exposure lock comes in handy when the area used to set exposure is much brighter or darker than its surroundings. With the subject positioned in the selected focus point and the shutter-release button pressed halfway, press the center of the sub-selector to lock exposure.
Page 130
Tip: Locking Exposure with the Shutter-Release Button If [On (half press)] is selected for Custom Setting c1 [Shutter-release button AE-L], exposure will lock while the shutter-release button is pressed halfway. Tip: Metered Area With [Spot metering], exposure will be locked at the value metered in a circle centered on the current focus point.
Exposure Compensation Exposure compensation is used to alter exposure from the value suggested by the camera. It can be used to make pictures brighter or darker. −1 EV No exposure compensation +1 EV Adjusting Exposure Compensation Hold the E button and rotate a command dial. Choose from values between –5 EV (underexposure) and +5 EV (overexposure).
Page 132
E icons and exposure indicators appear in the shooting display and control panel. In modes other than M, the zero (“0”) at the center of the exposure indicator flashes. The current value for exposure compensation can be confirmed by pressing the E button. Control panel Monitor Viewfinder...
Release Mode Choosing a Release Mode To choose the operation performed when the shutter-release button is pressed all the way down, hold the c button and rotate the main command dial. Options for the selected setting, if any, can be chosen by holding the c button and rotating the sub-command dial.
Page 134
Frame Advance Rate The frame rates for continuous low-speed and continuous high-speed modes can also be selected using Custom Setting d1 [Continuous shooting speed]. The actual frame rate when a frame advance rate of 8 fps is selected in continuous low-speed mode is 7.5 fps.
Page 135
Tip: The Memory Buffer While the shutter-release button is pressed halfway, the frame- count display will show the number of pictures that can be stored in the memory buffer. When the buffer is full, the display will show r000 and the frame rate will drop.
High-Speed Frame Capture (C30/C60/C120) For high-speed burst photography at frame rates of 30, 60, or 120 fps, hold the c button and rotate the main command dial to choose [C30], [C60], or [C120]. The maximum length for bursts taken using high-speed frame capture is approximately four seconds.
Page 137
High-Speed Frame Capture: Restrictions The options available for image area vary with the frame advance rate. [C30]: Choose from [FX (36×24)] and [DX (24×16)] [C60]: The only option available is [DX (24×16)] [C120]: The only option available is [FX (36×24)] If a DX lens is attached when [C120] is selected, the release mode will change to [C60] and image area will be fixed at [DX (24×16)].
Using the Self-Timer (E) In self-timer mode, pressing the shutter-release button all the way down starts a timer, and a photo is taken when the timer expires. Hold the c button and rotate the main command dial to select E. Hold the c button and rotate the sub-command dial to choose the self-timer delay.
ISO Sensitivity About ISO Sensitivity The camera’s sensitivity to light (ISO sensitivity) can be adjusted according to the amount of light available. In general, choosing higher values allows faster shutter speeds at the same aperture. Choose from settings of from ISO 64 to 25600. Extended settings of from about 0.3 to 1 EV (ISO 32 equivalent) below ISO 64 and 0.3 to 2 EV (ISO 102400 equivalent) above ISO 25600 are also available.
Page 140
Tip: The Photo Shooting Menu [ISO Sensitivity Settings] Option ISO sensitivity can also be adjusted using the [ISO sensitivity settings] item in the photo shooting menu. Tip: Hi 0.3–Hi 2.0 A setting of [Hi 0.3] corresponds to an ISO sensitivity approximately 0.3 EV higher than ISO 25600 (ISO 32000 equivalent) and [Hi 2.0] to an ISO sensitivity approximately 2 EV higher (ISO 102400 equivalent).
Auto ISO Sensitivity Control Auto ISO sensitivity control automatically adjusts ISO sensitivity if optimal exposure cannot be achieved at the value selected by the user. You can select an upper limit for auto ISO sensitivity control (100–Hi 2.0) to prevent ISO sensitivity being raised too high. Enabling Auto ISO Sensitivity Control Hold the S button and rotate the sub-command dial to select from ISO AUTO (auto ISO sensitivity control enabled) and ISO...
Page 142
Cautions: Auto ISO Sensitivity Control If the value currently selected for [ISO sensitivity] is higher than that chosen for [Maximum sensitivity], the value chosen for [ISO sensitivity] will serve as the upper limit for auto ISO sensitivity control. During flash photography, shutter speed is limited to the range defined by the values selected for Custom Settings e1 [Flash sync speed] and e2 [Flash shutter speed].
White Balance About White Balance White balance ensures that colors appear natural regardless of the color of the light source. The default setting (4) is suitable for use with most light sources, but if it fails to produce the desired results, other settings can be selected according to the weather or light source.
Page 144
Color Option Description * temperature The camera adjusts white balance for optimal results with most light sources. If an optional 4 [Auto] flash unit is used, white balance will be adjusted in accord with the conditions in effect when the flash fires.
Page 145
Color Option Description * temperature I [Fluorescent] m [Cool-white Approx. 4200 K fluorescent] Use under fluorescent lighting; choose a bulb n [Day white type according to the light source. Approx. 5000 K fluorescent] o [Daylight Approx. 6500 K fluorescent] Approx. 5400 K Use for flash photography. 5 [Flash] Direct color-temperature selection.
Page 146
D “Natural Light Auto” D [Natural light auto] may not produce the desired results under artificial light. Choose 4 [Auto] or an option that matches the light source. Studio Flash Lighting 4 [Auto] may not produce the desired results with large studio flash units. Use preset manual white balance or set white balance to 5 [Flash] and use fine-tuning to adjust white balance.
Page 147
Tip: Auto The photo info [Basic shooting data] page for pictures shot with 4 [Auto], D [Natural light auto], or L [Preset manual] selected for white balance lists the color temperature in effect at the time the picture was taken ( 219).
Fine-Tuning White Balance Each white balance option can be fine-tuned by up to six steps in either direction from the center along both the A (amber)–B (blue) and G (green)–M (magenta) axes. Using Buttons Choose a white balance option by holding the U button and rotating a command dial. Keeping the U button pressed, fine-tune white balance using the multi selector.
Page 149
Using the Menus Select [White balance] in the photo shooting menu, highlight the desired option, and press 2 as often as necessary to display fine-tuning options. For information on fine-tuning [Preset manual] white balance, see “Fine-Tuning Preset Manual White Balance” ( 161).
Page 150
Tip: The i Menu Pressing J when [White balance] is highlighted in the i menu displays a list of white balance options. If an option other than K [Choose color temperature] is highlighted, fine-tuning options can be displayed by pressing 3. Any changes to fine-tuning options can be previewed in the display.
Page 151
Tip: White Balance Fine-Tuning The colors on the fine-tuning axes are relative, not absolute. Selecting more of a color on a given axis does not necessarily result in that color appearing in pictures. For example, moving the cursor to “B” (blue) when a “warm”...
Choosing a Color Temperature Choose a color temperature by entering values for the A (amber)–B (blue) and G (green)–M (magenta) axes. Using Buttons Hold the U button and rotate the main command dial to select K [Choose color temperature]. Keeping the U button pressed, rotate the sub-command dial to choose a color temperature.
Page 153
Keeping the U button pressed, fine-tune white balance using the multi selector. Use the multi selector to position the cursor on the grid. The selected value is displayed to the right of the grid. The A (amber)–B (blue) axis corresponds to color temperature and is ruled in increments of 0.5.
Page 154
Fine-tune white balance. After choosing a color temperature, press the W (Q) button to display fine-tuning options. Use the multi selector to position the cursor on the grid. The cursor can be moved up to six steps from the center along either axis.
Page 155
Cautions: Color-Temperature Selection Do not use color-temperature selection with fluorescent light sources; instead, use the I [Fluorescent] option. When using color-temperature selection with other light sources, take a test shot to determine if the selected value is appropriate. Tip: The i Menu Pressing J when [White balance] is highlighted in the i menu displays a list of white balance options.
Preset Manual White balance settings such as 4 [Auto], J [Incandescent], and K [Choose color temperature] may fail to produce the desired results under mixed lighting or lighting with a strong color cast. Should this occur, white balance can be set to a value measured under the light source used in the final photograph.
Page 157
Select a preset. Hold the U button and rotate the sub-command dial until the desired white balance preset (d-1 to d-6) is displayed. Select direct measurement mode. Release the U button briefly and then press it again to enter direct measurement mode. L will flash in the shooting display.
Page 158
Position the white balance target (r) over a white or gray object and measure a value for preset manual white balance. Position the target (r) using the multi selector. To measure white balance, press the shutter-release button all the way down or press J. White balance can be measured multiple times while direct measurement mode is in effect.
Page 159
The Preset Manual White Balance Menu The preset manual white balance menu can be accessed by selecting [White balance] > L [Preset manual] in the photo shooting menu. The preset manual white balance menu offers options for copying values for preset manual white balance from an existing photograph or adding comments to or protecting white balance presets.
Page 160
Copying White Balance from a Photograph Follow the steps below to copy a value for white balance from an existing photograph to a selected preset. Select [White balance] in the photo shooting menu, then highlight [Preset manual] and press 2. Select a destination.
Page 161
Copy white balance. Press J to copy the white balance value for the highlighted photograph to the selected preset. If the highlighted photograph has a comment, the comment will be copied to the comment for the selected preset. Tip: Fine-Tuning Preset Manual White Balance The selected preset can be fine-tuned by selecting [Fine-tune] in the preset manual white balance menu.
Bracketing Bracketing automatically varies exposure, flash level, Active D-Lighting (ADL), or white balance slightly with each shot, “bracketing” the current value. Bracketing can be used in situations in which getting the right settings is difficult and there is not time to check results and adjust settings with each shot, or to experiment with different settings for the same subject.
Exposure and Flash Bracketing Vary exposure and/or flash level over a series of photographs. To perform exposure and/or flash bracketing, follow the steps below. No exposure compensation −1 EV +1 EV Choose the number of shots. Hold the BKT button and rotate the main command dial to choose the number of shots in the bracketing sequence.
Page 164
Select an exposure increment. Hold the BKT button and rotate the sub-command dial to choose the exposure increment. When [1/3 step] is selected for Custom Setting b2 [EV steps for exposure cntrl], the size of the increment can be chosen from 0.3 (¹⁄₃), 0.7 (²⁄₃), 1.0, 2.0, and 3.0 EV. Bracketing programs with an increment of 2.0 or 3.0 EV offer a maximum of 5 shots.
Page 165
Take pictures. Take the number of pictures in the bracketing program. The modified values for shutter speed and aperture are shown in the display. While bracketing is in effect, the shooting display shows a bracketing icon, a bracketing progress indicator, and the number of shots remaining in the bracketing sequence. After each shot, a segment will disappear from the indicator and the number of shots remaining will be reduced by one.
Page 166
Tip: Bracketing Options When [AE & flash bracketing] is selected, the camera varies both exposure and flash level. Select [AE bracketing] to vary only exposure, [Flash bracketing] to vary only flash level. Note that flash bracketing is available in i-TTL and, where supported, auto aperture (qA) flash control modes only 390, 830).
Page 167
Cancelling Bracketing To cancel bracketing, press the BKT button and rotate the main command dial until the number of shots in the bracketing sequence is zero (0F). The program last in effect will be restored the next time bracketing is activated. Bracketing can also be cancelled by performing a two-button reset ( 185), although in this case the bracketing program will not be restored the next time bracketing is activated.
White Balance Bracketing The camera creates multiple copies of each photograph, each with a different white balance. To use white balance bracketing: Choose the number of shots. Hold the BKT button and rotate the main command dial to choose the number of shots in the bracketing sequence.
Page 169
Select a white balance increment. Hold the BKT button and rotate the sub-command dial to choose the white balance increment. The size of the increment can be chosen from 1 (1 step), 2 (2 steps), or 3 (3 steps). Each step is equivalent to 5 mired. Higher “A” values correspond to increased amounts of amber.
Page 170
Take pictures. Each shot will be processed to create the number of copies specified in the bracketing program, and each copy will have a different white balance. Modifications to white balance are added to the white balance adjustment made with white balance fine-tuning. If the number of shots in the bracketing program is greater than the number of exposures remaining, the shutter release will be disabled.
ADL Bracketing The camera varies Active D-Lighting (ADL) over a series of exposures. To use ADL bracketing: Choose the number of shots. Hold the BKT button and rotate the main command dial to choose the number of shots in the bracketing sequence. At settings other than [0F], a bracketing icon and indicator will appear in the shooting display and control panel.
Page 172
The number of shots determines the bracketing sequence: No. of shots Bracketing sequence Off → Value selected in Step 2 Off → Low → Normal Off → Low → Normal → High [H1] Off → Low → Normal → High → Extra high 1 [H2] Low →...
Page 173
Choose the Active D-Lighting amount. Hold the BKT button and rotate the sub-command dial to choose the Active D-Lighting setting for the second shot when the number of shots in the bracketing sequence is 2. The bracketing sequence varies with the Active D-Lighting amount as follows: Amount Bracketing sequence Off →...
Page 174
Take pictures. Take the number of pictures in the bracketing program. While bracketing is in effect, the shooting display shows an ADL bracketing icon and the number of shots remaining in the bracketing sequence. After each shot, the number of shots remaining will be reduced by one.
Picture Controls About Picture Controls Choose image processing (“Picture Control”) options for new photos according to the scene or your creative intent. Choosing a Picture Control At default settings, Picture Controls can be selected by holding the g (Fn3) button and rotating the main command dial.
Page 176
Option Description [Portrait] Smooth complexions for natural-looking portraits. [Landscape] Shoot vibrant landscapes and cityscapes. Details are preserved over a wide tone range, from highlights [Flat] to shadows. Choose for photographs that will later be extensively processed or retouched. Creative Picture Controls offer unique combinations of hue, k01–...
Modifying Picture Controls Picture Controls can be adapted to suit the scene or the photographer’s creative intent. Select a Picture Control. Select [Set Picture Control] in the photo shooting or video recording menu and then highlight the desired Picture Control and press 2.
Page 178
Picture Control Settings Option Description [Effect level] Mute or heighten the effect of Creative Picture Controls. Use [Quick sharp] to quickly adjust levels for balanced [Quick sharp] [Sharpening], [Mid-range sharpening], and [Clarity]. These parameters can also be adjusted individually. [Sharpening] Control the sharpness of details and outlines.
Page 179
The j Indicator The j indicator under the value display in the Picture Control setting menu indicates the previous value for the setting. “A” (Auto) Selecting the [A] (auto) option available for some settings lets the camera adjust the setting automatically.
Page 180
Tip: The i Menu Highlighting [Set Picture Control] in the i menu and pressing J displays a Picture Control list. Highlight a Picture Control and press 3 to edit settings while previewing the effect in the display. Press 1 or 3 to highlight settings. Press 4 or 2 to choose a value in increments of 1, or rotate the sub-command dial to choose a value in increments of 0.25.
Custom Picture Controls Save modified Picture Controls as custom Picture Controls. Option Description Create a new custom Picture Control based on an existing preset or custom Picture [Save/edit] Control, or edit existing custom Picture Controls. [Rename] Rename custom Picture Controls. [Delete] Delete custom Picture Controls.
Page 182
Adjust settings. The options and procedure are the same as for [Set Picture Control]. Press J to display [Save as] options when settings are complete. To abandon any changes and start over from default settings, press the O (Q) button. Select a destination.
Page 183
Press the X button. Text entry will end. The new Picture Control will be added to the Picture Control list. Picture Controls...
Page 184
The Original Picture Control Icon The original preset Picture Control on which the custom Picture Control is based is indicated by an icon in the edit display. Custom Picture Control Options The options available with custom Picture Controls are the same as those on which the custom Picture Control was based.
Two-Button Reset The camera settings listed below can be restored to default values by pressing the two buttons marked with green I dots (BKT and E) at the same time and holding them for over two seconds (the shooting display and control panel turn off briefly while settings are reset). Photo Shooting Menu With the exceptions of multiple exposure, interval timer, time-lapse video, and focus shift, only settings in the current shooting menu bank are affected.
Page 186
Option Default Set Picture Control (HLG) Standard Active D-Lighting Skin softening Portrait impression balance Photo flicker reduction High-frequency flicker reduction Metering Matrix metering Flash mode Fill flash Flash compensation Off (0.0) Focus mode Single AF AF-area mode Single-point AF 1 Auto bracketing 2 Multiple exposure...
Video Recording Menu Option Default ISO sensitivity settings Maximum sensitivity 25600 Auto ISO control (mode M) ISO sensitivity (mode M) White balance Same as photo settings Set Picture Control Same as photo settings HLG quality Quick sharp Contrast Saturation Active D-Lighting Skin softening...
Other Settings Option Default Focus point Center Preset focus point Center Shooting mode Flexible program Release mode Single frame Exposure compensation Off (0.0) AE lock (hold) FV lock Two-Button Reset...
Video Recording Video File Types Use [Video file type] in the video recording menu to choose the video file type. You have a choice of NEV, MOV, and MP4 formats. YCbCr/ Option Description Bayer This option assumes the footage will later undergo RAW processing and editing using a professional high-performance computer system of the type typically employed for editing video ( ...
Page 191
YCbCr/ Option Description Bayer Choose for footage destined for editing post- production. You have a choice of two tone modes: [SDR] YCbCr [ProRes 422 HQ 10-bit (MOV)] and [N-Log]. (4 : 2 : 2) Footage is recorded using All-I intra-frame compression. Audio is recorded in Linear PCM format. This option assumes the footage will later undergo editing using a professional high-performance computer system of the type typically employed...
SDR. It is available only when [H.265 10-bit (MOV)] is selected for [Video file type]. This mode uses Nikon’s unique log curve. Choose for pictures with a wide dynamic [N-Log] range. 3D LUTs for use with N-Log curves can be applied post-production for pictures that display beautifully on monitors that support Rec.
Video Frame Size and Rate Options Video frame size (in pixels) and frame rate can be selected using [Frame size/frame rate] in the video recording menu. The options available for frame size vary with the settings chosen for [Video file type] in the video recording menu.
Bit Rate The bit rate varies with the video file type. In the case of [N-RAW 12-bit (NEV)], the bit rate varies with the option selected for [Video quality (N-RAW)] in the video recording menu. ProRes RAW HQ 12-bit and ProRes 422 HQ 10-bit data specifications are available from the Apple website.
Page 197
Option [[DX] 5392×3032; 30p] Approx. 1480 Mbps [[DX] 5392×3032; 25p] Approx. 1240 Mbps Approx. 28 Mbps [[DX] 5392×3032; 24p] Approx. 1190 Mbps [[2.3×] 3840×2160; 120p] Approx. 3020 Mbps Approx. 120 Mbps [[2.3×] 3840×2160; 100p] Approx. 2510 Mbps Normal-Quality N-RAW 12-Bit NEV The average bit rates for NEV videos and for the MP4 videos recorded for playback purposes when [Normal] is selected for [Video quality (N-RAW)] are as follows.
Video Image Area Options The image area for videos can be selected using [Image area] > [Choose image area] in the video recording menu. The crop used for filming video varies with the option selected. Regardless of the option selected, the aspect ratio is 16 : 9. Select [FX] to shoot videos in what is referred to as “FX-based video format”, [DX] to shoot in “DX-based video format”.
Page 201
The option currently selected is shown by an icon in the display. If [ON] is chosen for [Image area] > [DX crop alert] in the video recording menu, an image-area icon will flash in the shooting display when the DX or 2.3× crop is selected. The sizes of the different crops are shown below.
Points to Note When Filming Videos Note the following points when recording videos: Each video can be up to 125 minutes in length. Each video recorded to a card with a capacity of 32 GB or less will be saved across a maximum of 8 files.
Page 203
Tip: Adjusting White Balance During Video Recording White balance can be adjusted during video recording by holding the U button and rotating a command dial. Tip: Using a Fixed Shutter Speed In mode M, shutter speed can be set to values between ¹⁄₂₅ s and ¹⁄₃₂₀₀₀ s (the slowest available shutter speed varies with the frame rate).
Viewing and Editing RAW Videos RAW videos can only be viewed and edited using computer software that supports the RAW video format. Nikon’s NX Studio software supports only the display of the MP4 proxy videos recorded alongside RAW videos. RAW Video...
Recording HLG Video Video recorded in Hybrid Log Gamma (HLG) format can be used for HDR broadcasting and the like. To record HLG video, select [H.265 10-bit (MOV)] for [Video file type] in the video recording menu and choose the [HLG] tone mode. o will appear in the shooting display.
Page 206
Viewing and Editing HLG Videos HLG videos can only be viewed and edited using computer software that supports the HLG video format. Nikon’s NX Studio software shows HLG videos in the thumbnail list but cannot be used to view or edit them.
Recording N-Log Video Log recording uses light levels digitized via a log function. To enable log recording using Nikon’s unique “N-Log” log function, select [N-RAW 12-bit (NEV)], [ProRes RAW HQ 12-bit (MOV)], [ProRes 422 HQ 10-bit (MOV)], or [H.265 10-bit (MOV)] for [Video file type] in the video recording menu and choose [N-Log] as the tone mode.
View Assist You may find that the preview in the shooting display during N-Log recording lacks contrast. Selecting [ON] for Custom Setting g11 [View assist] simplifies colors for enhanced contrast. p will appear in the shooting display. Colors in the actual recorded footage are unaffected. Contrast is also enhanced when N-Log footage is viewed on the camera.
Hi-Res Zoom Selecting [ON] for [Hi-Res Zoom] in the video recording menu lets you zoom in on your subject with no loss in resolution, even without a zoom lens. Hi-Res Zoom is available when all the following conditions are met: [FX] is selected for [Image area] >...
Page 210
Tip: Custom Controls for Hi-Res Zoom The zoom position for Hi-Res Zoom can also be adjusted using controls to which [Hi-Res Zoom +] and [Hi-Res Zoom −] have been assigned via Custom Setting g2 [Custom controls]. Zoom control for Hi-Res Zoom can be assigned to the camera [Fn1 button] and [Fn2 button], to the lens Fn ring via [Lens Fn ring (clockwise)] and [Lens Fn ring (counterclockwise)], and via [Lens control ring] to the lens control ring.
Viewing Pictures Viewing Pictures Full-Frame Playback Press the K button to view the most recent picture full frame in the display. Press 4 to return to the previous frame, 2 to skip to the next frame. Press 1, 3, or the DISP button to view more information on the current picture ( 214).
Thumbnail Playback To view multiple pictures, press the W (Q) button when a picture is displayed full frame. The number of pictures displayed increases from 4 to 9 to 72 each time the W (Q) button is pressed, and decreases with each press of the X button. Highlight pictures using 1, 3, 4, or 2.
Page 213
Touch Controls Touch controls can be used when pictures are displayed in the monitor ( 56). Auto Picture Rotation To display “tall” (portrait-orientation) photographs in tall orientation, select [ON] for [Auto-rotate pictures] in the playback menu. Picture Review When [On] is selected for [Picture review] in the playback menu, photographs are automatically displayed after shooting;...
Photo Information Photo information is superimposed on pictures displayed in full-frame playback. Press 1, 3, or the DISP button to cycle through photo information as shown below. * Basic information Shooting data * * Exposure data Overview data * * Highlight display None (picture only) *...
Exposure Data Current card slot Aperture ( 122, 123) Folder number–frame number ( 424) Exposure compensation value ( 131) * Shooting mode ( 121) ISO sensitivity ( 139) Shutter speed ( 122, 123) Displayed in red if the picture was taken with auto ISO sensitivity control enabled. Highlight Display Highlights (areas that may be overexposed) flash in the display.
RGB Histogram White balance ( 143) Histogram (RGB channel) Color temperature ( 152) Histogram (red channel) Preset manual ( 156) Histogram (green channel) White balance fine-tuning ( 148) Histogram (blue channel) Photo Information...
Page 218
Playback Zoom To zoom in on the picture in the histogram display, press X. The histogram will be updated to show only the data for the portion of the picture visible in the display. Use the multi selector to scroll to areas of the frame not visible in the monitor.
Shooting Data View the settings in effect at the time the picture was taken. The shooting data list has multiple pages, which can be viewed by pressing 1 or 3. The information displayed can be selected using [Playback display options] > [Detailed shooting data] in the playback menu. Basic Shooting Data Metering ( 461)
Page 220
Flash Data Displayed only if photo was taken with optional flash unit ( 387, 398). Flash type Flash control mode ( 391) Remote flash control Flash compensation ( 395) Flash mode ( 393) Picture Control/HLG data 1 Picture Control ( 175) Skin softening ( 454)
Page 221
Other Shooting Data High ISO NR ( 450) Vignette control ( 451) Long-exposure noise reduction ( 449) History of retouches made using Active D-Lighting ( 447) [Retouch] option in playback i menu HDR strength ( 479) 248). Changes are listed in the order applied.
Page 222
Location Data Location data must be downloaded from a smart device or GPS receiver and are displayed only if embedded in the picture at the time it was taken. The items listed vary with the smart device or GPS receiver from which the data were acquired. The location data recorded with videos are those reported at the start of recording.
Page 223
IPTC Data Caption Category Event ID Supp. Cat. (supplemental categories) Headline Byline Object name Byline title City Writer/Editor State Credit Country Source Photo Information...
Overview 8 7 6 Frame number/total number of frames Time of recording ( 713) Camera name Date of recording ( 713) Histogram ( 218) Current card slot Image quality ( 101) Folder name ( 424) Image size ( 103) File name ( 427) Image area ( Rating (...
File Info Voice memo indicator ( 288) IPTC preset indicator ( 735) 1 Protect status ( 235) Focus point ( 114) Retouch indicator ( 248) Frame number/total number of frames Upload marking ( 238) First picture in burst/total number of pictures in burst ( 697) Rating (...
The i Button (Playback Mode) Pressing the i button during playback zoom or full-frame or thumbnail playback displays the i menu for playback mode. Highlight items and press J or 2 to select. Press the i button again to return to playback. Photos Option Description...
Page 228
Option Description [Select for upload to smart device] [Select for upload to Select the current picture for upload ( 238). The option displayed computer] varies with the destination currently selected for upload. [Select for upload (FTP)] [Select all for Mark for upload all pictures meeting the current filter criteria ( 239).
Page 229
Option Description Choose a slot and folder for playback. Highlight a slot and press 2 to [Choose slot and display a list of the folders on the memory card in the selected slot. You folder] can then highlight a folder and press J to view the pictures it contains. Add protection to or remove protection from the current picture [Protect] 235).
Page 230
Tip: "Side-by-Side Comparison" Choose [Side-by-side comparison] to compare retouched copies with the unretouched originals. Options used to create copy Retouched copy Source picture The source picture is displayed on the left, the retouched copy on the right. The options used to create the copy listed at the top of the display. Press 4 or 2 to switch between the source picture and the retouched copy.
Videos Option Description [Rating] Rate the current picture ( 237). [Select for upload to computer] Select the current picture for upload ( 238). These options are displayed only if the camera is connected to a computer or FTP server. [Select for upload (FTP)] [Select all for Mark for upload all pictures meeting the current filter criteria (...
Videos (Playback Paused) Option Description [Trim video] Trim unwanted footage ( 280). [Save current frame] Save a selected frame as a JPEG still ( 283). Save the frames in a selected length of footage as a series of [Save consecutive frames] individual JPEG images ( ...
Playback Zoom To zoom in on a photo displayed in full-frame playback, press X or J or give the display two quick taps. [FX (36×24)]-format photos can be zoomed in to a maximum of approximately 32× ([Large] pictures), 24× ([Medium]), or 16× ([Small]). Faces detected during zoom are indicated by white borders;...
Page 234
Operation Description Faces detected during zoom are indicated by white borders in the navigation window. Rotate the sub- command dial or tap the on-screen Select faces guide to view other faces. Rotate the main command dial to view the same location in other photos View other without changing the zoom ratio (selecting a video cancels zoom).
Protecting Pictures from Deletion Pictures can be protected to prevent their being deleted accidentally. Protected pictures will however be deleted when the memory card is formatted ( 710). Select a picture. Display the picture in full-frame playback or playback zoom. Alternatively, you can highlight the picture in the thumbnail list using the multi selector.
Page 236
Voice Memos Protecting photos also protects any voice memos recorded with the pictures. Voice memos cannot be protected separately. Caution: Uploading Protected Pictures via FTP The copies on the FTP server will not be protected even if the originals are. Markings can be added using ratings.
Rating Pictures Rate pictures. Select the desired picture with the multi selector and press the i button. Highlight [Rating] and press 2. Choose a rating. Rotate the main command dial to highlight the desired rating and press J to select. Choose from ratings of from zero to five stars, or select d to mark the picture as a candidate for later deletion.
Selecting Pictures for Upload Follow the steps below to select the current picture for upload to a smart device, computer, or FTP server. The i menu items used to select pictures for upload vary with the type of device connected: [Select for upload to smart device]: Displayed when the camera is connected to a smart device using [Connect to smart device] in the network menu ( 767).
Filtered Playback Select [Filtered playback] in the i menu to view only pictures that meet the criteria chosen for [Filtered playback criteria] in the playback menu or playback i menu. “Filtered Playback Criteria” Highlight options and press J to select (M) or deselect (U). During filtered playback, only pictures that meet all criteria marked with a check (M) will be displayed.
Page 240
During filtered playback, a white border appears around the display. To end filtered playback, select [Filtered playback] again. Filtered Playback...
Viewing Slide Shows To view a slide show in which pictures are played back one at a time in the order recorded, select [Slide show] in the i menu. You can also choose how long any photos in the show are displayed. Select the starting picture using the multi selector and press the i button.
During the Show The following operations can be performed while the show is in progress: Operation Description Skip back/skip ahead Press 4 to return to the previous frame, 2 to skip to the next frame. View additional photo Press 1, 3, or DISP to choose the photo info displayed. To hide photo info info, select [None (picture only)].
Deleting Pictures Follow the steps below to delete pictures from memory cards. Note that pictures cannot be recovered once deleted. Pictures that are protected, however, cannot be deleted. Using the Delete Button Press the O (Q) button to delete the current picture. Select the desired picture with the multi selector and press the O (Q) button.
Deleting Multiple Pictures Use [Delete] in the playback menu to delete multiple pictures at once. Note that depending on the number of pictures, some time may be required for deletion. Option Description [Selected pictures] Delete selected pictures. [Candidates for Delete pictures rated d (candidate for deletion). deletion] [Pictures shot on Delete all pictures taken on selected dates.
Page 245
Deleting Selected Pictures Select pictures. Highlight pictures and press the W (Q) button to select; selected pictures are marked with a check ( ). To remove the check ( ) and deselect the current picture, press the W (Q) button again. Repeat until all the desired pictures are selected.
Page 246
Candidates for Deletion Select pictures. The camera will list all pictures rated d (candidate for deletion). Pictures you do not currently wish to delete can be deselected by highlighting them using the multi selector and pressing W (Q). To view the highlighted picture full screen, press and hold the X button. Delete the pictures.
Page 247
Deleting All Pictures Choose a memory card. Press 1 or 3 to highlight the slot containing the memory card from which the pictures will be deleted and press J. Delete the pictures. A confirmation dialog will be displayed showing the name of the folder containing the photos to be deleted.
Retouching Photographs Retouching Photographs Retouched copies can be created from existing pictures. Retouched copies are saved to new files, separate from the original pictures. Option Description [RAW processing Save a copy of the current NEF (RAW) picture in another format such as (current picture)] JPEG ( ...
Page 249
Option Description Compare the pixels at each point in multiple pictures and select the [Lighten] brightest to create a new picture in JPEG format ( 274). Compare the pixels at each point in multiple pictures and select the [Darken] darkest to create a new picture in JPEG format ( 274).
Page 250
Cautions: Retouch The camera may not be able to display or retouch images that were taken or retouched using other cameras or that have been retouched on a computer. If no actions are performed for a brief period, the display will turn off and any unsaved changes will be lost.
RAW Processing RAW processing is used to save NEF (RAW) pictures in other formats, such as JPEG. Depending on the tone mode selected when the picture was taken, copies can be saved in either JPEG or HEIF format. Caution: RAW Processing RAW processing is available only with NEF (RAW) images created with this camera.
Page 252
Choose a destination. Press 1 or 3 to highlight a card slot and press J. You will not be prompted to select the slot if only one memory card is inserted. Choose settings for the JPEG copy in the [RAW processing] display. The following settings can be adjusted: Image quality ( 101)
Page 253
Processing Multiple Pictures Display an NEF (RAW) picture shot with [SDR] selected for tone mode and then press the i button. Select [Retouch] in the i menu, then highlight [RAW processing (multiple pictures)] and press 2. Choose how pictures will be selected and where the copies will be saved.
Page 254
Select the source slot. Highlight the slot with the card containing the NEF (RAW) images and press 2. You will not be prompted to select the slot if only one memory card is inserted. Select photographs. If you chose [Select picture(s)]: Highlight pictures using the multi selector.
Page 255
Choose settings for the JPEG copies in the [RAW processing] display. The following settings can be adjusted: Image quality ( 101) Image size ( 103) Exposure compensation ( 131) White balance ( 143) Picture Control ( 175) Color space ( 446) Active D-Lighting ( 447)
Processing Photos Shot Using the “HLG” Tone Mode Applying RAW processing to photos shot with [HLG] selected for tone mode creates HEIF copies. NEF (RAW) pictures taken with [HLG] selected for tone mode can also be saved in JPEG format ( ...
Page 257
Choose settings for the HEIF copy in the [RAW processing (HEIF)] display. The following settings can be adjusted: Image quality ( 101) Image size ( 103) Exposure compensation ( 131) White balance ( 143) Picture Control (HLG; 442) High ISO NR ( 450) Vignette control ( 451)
Page 258
Tip: Creating JPEG Copies from RAW Photos Shot Using the HLG Tone Mode Selecting [To RAW processing (JPEG)] in Step 4 displays the [RAW processing (JPEG)] dialog, where you can adjust settings for saving the copy in JPEG format. To save the JPEG copy, highlight [EXE (save in JPEG format)] and press J.
Page 259
Choose how pictures will be selected and where the copies will be saved. Option Description Create HEIF copies of selected NEF (RAW) pictures. Multiple NEF [Select picture(s)] (RAW) pictures can be selected. [Select date] Create HEIF copies of all NEF (RAW) pictures taken on selected dates. [Select folder] Create HEIF copies of all NEF (RAW) pictures in a selected folder.
Page 260
Select photographs. If you chose [Select picture(s)]: Highlight pictures using the multi selector. To view the highlighted picture full screen, press and hold the X button. To select the highlighted picture, press the W (Q) button. Selected pictures are marked with a check ( ).
Page 261
Choose settings for the HEIF copies in the [RAW processing (HEIF)] display. The following settings can be adjusted: Image quality ( 101) Image size ( 103) Exposure compensation ( 131) White balance ( 143) Picture Control (HLG; 442) High ISO NR ( 450) Vignette control ( 451)
Page 262
Tip: Creating JPEG Copies from RAW Photos Shot Using the HLG Tone Mode Selecting [To RAW processing (JPEG)] in Step 6 displays the [RAW processing (JPEG)] dialog, where you can adjust settings for saving the copies in JPEG format. To save the JPEG copies, highlight [EXE (save in JPEG format)] and press J.
Trim Create a cropped copy of the current photograph. The photograph is displayed with the selected crop shown in yellow; create a cropped copy as described below. Operation Description Size the crop Press X or W (Q) to choose the crop size. Change the crop aspect ratio Rotate the main command dial to choose the crop aspect ratio.
Resize Create small copies of selected photographs. Use [Resize (current picture)] to resize the current picture, or [Resize (multiple pictures)] to resize multiple pictures. Caution: Resize Depending on the copy size, playback zoom may not be available when resized copies are displayed. Resizing Cropped Pictures Pictures cropped to aspect ratios of 4 : 3 or 3 : 4 cannot be resized.
Resizing Multiple Pictures Select [Retouch] in the i menu, then highlight [Resize (multiple pictures)] and press 2. Choose a size. Highlight [Choose size] and press 2. Highlight the desired size (length in pixels) using 1 and 3 and press J. Choose how pictures are selected.
Page 266
Select the source slot. Highlight the slot with the card containing the desired pictures and press 2. You will not be prompted to select the slot if only one memory card is inserted. Choose pictures. If you chose [Select picture(s)]: Highlight pictures using the multi selector.
D-Lighting D-Lighting brightens shadows. It is ideal for dark or backlit photographs. Before After The effect can be previewed in the edit display. To view the unedited picture, press and hold the DISP button. Press 1 or 3 to choose the amount of correction performed. The effect can be previewed in the edit display.
Straighten Rotate pictures by up to ±5° in increments of approximately 0.25°. The effect can be previewed in the edit display. To view the unedited picture, press and hold the DISP button. The greater the rotation, the more will be trimmed from the edges.
Distortion Control Create copies with reduced peripheral distortion, reducing barrel distortion in pictures taken with wide-angle lenses or pincushion distortion in pictures taken with telephoto lenses. If the camera detects distortion, it will offer a choice of [Auto] and [Manual]. Select [Auto] to let the camera correct distortion automatically.
Perspective Control Create copies that reduce the horizontal and vertical effects of perspective in photos taken looking up from the base of a tall object. The effect can be previewed in the edit display. To view the unedited picture, press and hold the DISP button. Note that greater amounts of perspective control result in more of the edges being cropped out.
Monochrome Copy photographs in a selected monochrome tint. Option Description [Black-and-white] Copy photographs in black-and-white. [Sepia] Copy photographs in sepia. [Cyanotype] Copy photographs in blue-and-white monochrome. The effect can be previewed in the edit display. To view the unedited picture, press and hold the DISP button. Highlighting [Sepia] or [Cyanotype] and pressing 2 displays saturation options for the selected monochrome tint;...
Overlay (Add) Combine two existing photographs to create a single picture that is saved separately from the originals. Select [Retouch] in the i menu, then highlight [Overlay (add)] and press 2. Select pictures. Highlight pictures using the multi selector. To view the highlighted picture full screen, press and hold the X button.
Page 273
Save the overlay. Press J to save the overlay. Cautions: “Overlay (Add)” Colors and brightness in the preview may differ from the final picture. Only pictures created with this camera can be selected. Pictures created with other models cannot be selected. The overlay will be the same size as the smallest of the two component pictures.
“Lighten” and “Darken” The camera compares multiple selected pictures and selects only the brightest or darkest pixels at each point in the picture to create a single new JPEG copy. Select [Retouch] in the i menu, then highlight [Lighten] or [Darken] and press 2. [Lighten]: The camera compares the pixels in each picture and uses only the brightest.
Page 275
Select the pictures. If you chose [Select individual pictures]: Highlight pictures using the multi selector. To view the highlighted picture full screen, press and hold the X button. To select the highlighted picture, press the W (Q) button. Selected pictures are marked with a check ( ).
Page 276
Cautions: “Lighten” and “Darken” Only pictures created with this camera can be selected. Pictures created with other models cannot be selected. The overlay will include only pictures created with the same options selected for [Image area] > [Choose image area] in the photo shooting menu. The image quality setting for the completed overlay is that of the highest quality picture it contains.
Motion Blend The camera examines a selected burst of pictures to detect moving subjects and overlays them to create a single JPEG image. Select [Retouch] in the i menu, then highlight [Motion blend] and press 2. Select the source slot. Highlight the slot with the card containing the desired pictures and press 2.
Page 278
Save the overlay. Highlight [Yes] in the confirmation dialog and press J to save the overlay. Cautions: “Motion Blend” The final picture may differ from the preview both in how it looks (including color and brightness) and in how the pictures are combined. Only pictures created with this camera can be selected.
Editing Videos Editing Videos Videos can be edited using the following options: Option Description [Trim video] Trim unwanted footage. [Save current frame] Save a selected frame as a JPEG still. Save the frames in a selected length of footage as a series of [Save consecutive frames] individual JPEG images.
Trimming Videos Trim unwanted footage. Display a video full frame. Pause the video on the new opening frame. Press J to start playback. Press 3 to pause. Your approximate position in the video can be ascertained from the video progress bar. Press 4 or 2 or rotate the command dials to locate the desired frame.
Page 281
Choose the start point. To create a copy that begins from the current frame, highlight [Start point] and press J. Confirm the new start point. If the desired frame is not currently displayed, press 4 or 2 to advance or rewind a frame at a time. Rotate the main command dial one stop to skip ahead or back 10 frames.
Page 282
Preview the copy. To preview the copy, highlight [Preview] and press J (to interrupt the preview and return to the save options menu, press 1). To abandon the current copy and return to Step 5, highlight [Cancel] and press J. Choose a save option. Choose [Save as new file] to save the edited copy as a new file.
Saving the Current Frame as a JPEG Still Stills can be created from individual frames of existing videos. You can create a single still from the current frame or a series of stills from a selected length of footage. Pause the video on the desired frame. Press 3 to pause playback.
Creating Stills from a Selected Length of Footage The frames in a selected length of footage can be saved as a series of individual JPEG images. Pause the video on the desired frame. Press 3 to pause playback. Your approximate position in the video can be ascertained from the video progress bar.
Page 285
Press J. The selected footage will be saved as a series of JPEG stills. The number varies with the video frame rate. “Save Consecutive Frames” Stills are saved at the dimensions selected for [Frame size/frame rate] in the video recording menu when the video was recorded.
Voice Memos Recording Voice Memos Voice memos up to 60 seconds long can be added to photographs. Select the photograph. Only one voice memo can be recorded per picture; additional voice memos cannot be recorded for pictures already marked with a h icon. The existing voice memo must be deleted before another can be recorded ( 289).
Page 287
Recording Not Available Voice memos cannot be added to videos or Image Dust Off reference data. Recording Restrictions Voice memos cannot be recorded if: the photo/video selector is rotated to 1 or a multiple exposure is in progress. Caution: Recording Voice Memos Touch controls are disabled and other pictures cannot be displayed while recording is in progress.
Playing Voice Memos To play voice memos when viewing photographs marked with h icons, press the i button, highlight [Play voice memo], and press Interrupting Playback Pressing the shutter-release button or operating other camera controls may end playback. Playback ends automatically when another picture is selected or the camera is turned off. Tip: Using Buttons for Voice Memo Playback Voice memos can be played by pressing a control to which [Play voice memo] has been assigned using Custom Setting f3 [Custom controls (playback)].
Deleting Voice Memos To delete the voice memo from the current photo, press the O (Q) button; a confirmation dialog will be displayed as shown. To delete both the photo and the voice memo, highlight [Picture and voice memo] and press O (Q). To delete only the voice memo, highlight [Voice memo only] and press O (Q).
Connecting to HDMI TVs and Recorders Connecting to HDMI Devices The camera can be connected to TVs, recorders, and other devices featuring HDMI connectors. Use a third-party Type A HDMI cable. The cable must be purchased separately. Always turn the camera off before connecting or disconnecting a cable.
After tuning the TV to the HDMI input channel, turn the camera on and press the K button to view pictures on the television screen. Audio playback volume can be adjusted using the controls on the TV. Camera controls cannot be used.
Recorders In video mode, the camera can record directly to connected HDMI recorders. If a memory card is inserted in the camera when it is connected to a recorder, video will be recorded both to the recorder and the memory card. If no memory card is inserted, the footage will be recorded only to the external device.
Adjusting Settings Use the [HDMI] item in the setup menu to adjust settings for HDMI output. Option Description The format for output to HDMI devices can be selected from [Auto], [Output [4320p (progressive)], [2160p (progressive)], [1080p (progressive)], [1080i resolution] * (interlaced)], and [720p (progressive)].
Page 294
“Output Resolution” When [Auto] is selected for [HDMI] > [Output resolution] in the setup menu, the camera automatically detects whether the external recorder supports the frame size and rate selected on the camera. If it does not, the camera will search for a supported resolution and frame rate in the order listed below.
Page 296
Frame Rates for “Output Resolution” Options Other Than “Auto” Video recording rates of 120p, 100p, 60p, or 50p will be adjusted as follows if not compatible with the frame rate chosen for the external recorder. 120p: The frame rate will first drop to 60p. If 60p is also not supported, it will drop to 30p. 100p: The frame rate will first drop to 50p.
YCbCr and Bit Depth The YCbCr value and bit depth for footage output to external HDMI devices varies with the options selected for [Video file type] and [Frame size/frame rate] in the video recording menu. Frame size/frame Video file type YCbCr and bit depth rate 8256×4644...
Frame size/frame Video file type YCbCr and bit depth rate 7680×4320 4:2:0 8-bit 3840×2160 120p/ 100p H.265 8-bit (MOV) 3840×2160 60p/50p/30p/ 4:2:2 8-bit 25p/24p 1920×1080 H.264 8-bit (MP4) 1920×1080 4:2:2 8-bit Recording to External Recorders That Support a Bit Depth of 10 Bits The HDMI signal will be output at a bit depth of 10 bits only to HDMI recorders that support this option.
External Recording Control Choosing [ON] for [External rec. cntrl (HDMI)] in the video recording menu allows camera controls to be used to start and stop recording on the external recorder. For information on whether your recorder supports external recording control, consult the manufacturer.
The SnapBridge app can be downloaded from the Apple App Store or on Google Play™. Visit the Nikon website for the latest SnapBridge news. Carefully read any license agreements or the like displayed when SnapBridge is launched and only proceed if you are willing to accept them.
What SnapBridge Can Do for You The tasks that can be performed using the SnapBridge app are outlined below. For details, see the SnapBridge app online help: https://nikonimglib.com/snbr/onlinehelp/en/index.html Downloading Pictures from the Camera Download existing pictures to your smart device. They can also be downloaded automatically as they are taken.
Wireless Connections Use the SnapBridge app for wireless connections between the camera and your smart device. You can connect via either Bluetooth ( 302) or Wi-Fi ( 305). Connecting using Bluetooth allows pictures to be uploaded automatically as they are taken. Connecting via Bluetooth (Pairing) Before connecting via Bluetooth for the first time, you will need to pair the camera and smart device.
Page 303
Camera: Select [Connect to smart device] > [Pairing (Bluetooth)] in the network menu, then highlight [Start pairing] and press J. The camera name will be displayed in the monitor. Smart device: Launch the SnapBridge app and tap [Connect to camera] in the tab.
Page 304
Pairing Error If you wait too long between pressing the button on the camera and tapping the button on the smart device in Step 4, the device will display an error message and pairing will fail. If you are using an Android device, tap [OK] and return to Step 1. If you are using an iOS device, dismiss the SnapBridge app and check that it is not running in the background, then request iOS to “forget”...
Connecting via Wi-Fi (Wi-Fi Mode) In Wi-Fi mode, the camera connects directly to the smart device via Wi-Fi, no Bluetooth pairing required. Before Connecting (Wi-Fi Mode) Enable Wi-Fi on the smart device. For details, see the documentation provided with the device. Ensure that the batteries in the camera and smart device are fully charged to prevent the devices turning off unexpectedly.
Page 306
Camera: Select [Connect to smart device] > [Wi-Fi connection] in the network menu, then highlight [Establish Wi-Fi connection] and press J. The camera SSID and password will be displayed. Smart device: Follow the on-screen instructions to establish a Wi-Fi connection. On iOS devices, the “Settings” app will launch. Tap [< Settings] to open [Settings], then scroll up and tap [Wi‑Fi] (which you’ll find near the top of the settings list) to display Wi-Fi settings.
Page 307
The camera and smart device are now connected via Wi-Fi. For information on using the SnapBridge app, see online help. Terminating Wi-Fi Mode To end the Wi-Fi connection, tap in the SnapBridge tab. When the icon changes to , tap and select [Exit Wi-Fi mode.].
Connecting to Computers or FTP Servers Making the Connection The camera can be connected to a computer or FTP server using any of the methods below. Computers: Connecting via USB Install NX Studio software on your computer to download pictures from cameras connected via USB ( ...
Computers: Connecting via Ethernet Connect to computers via a third-party USB-to-Ethernet adapter connected to the camera’s Type C USB data connector ( 328). The connection can be used to upload pictures ( 359) or to control the camera remotely from computers on the network running Camera Control Pro 2 (available separately) or free NX Tether software ( ...
Installing NX Studio You will need an Internet connection when installing NX Studio. Visit the Nikon website for the latest information, including system requirements. Download the latest NX Studio installer from the website below and follow the on-screen instructions to complete installation.
NX Studio. If a message is displayed prompting you to choose a program, select Nikon Transfer 2. If Nikon Transfer 2 does not start automatically, launch NX Studio and click the “Import” icon. Computers: Connecting via USB...
Page 312
Click [Start Transfer]. Pictures on the memory card will be copied to the computer. Turn the camera off. Disconnect the USB cable when transfer is complete. Computers: Connecting via USB...
Page 313
Transfer 2. macOS If Nikon Transfer 2 does not start automatically, confirm that the camera is connected and then launch Image Capture (an application that comes with macOS) and select Nikon Transfer 2 as the application that opens when the camera is detected.
Once the devices are paired, you will be able to connect to the computer from the camera. The Wireless Transmitter Utility is available for download from the Nikon Download Center. Check the version and system requirements and be sure to download the latest version.
Connecting to Computers via Wireless LAN The camera can connect to computers either by direct wireless link (access-point mode) or via a wireless router on an existing network, including home networks (infrastructure mode). Direct Wireless Connection (Access-Point Mode) The camera and computer connect via direct wireless link.
Page 316
Name the new profile. To proceed to the next step without changing the default name, press X. Whatever name you choose will appear in the network menu [Connect to computer] > [Network settings] list. To rename the profile, press J. For information on text entry, see “Text Entry”...
Page 317
Establish a connection to the camera. Windows: Click the wireless LAN icon in the taskbar. Select the SSID displayed by the camera in Step 4. When prompted to enter the network security key, enter the encryption key displayed by the camera in Step 4. The computer will initiate a connection to the camera.
Page 318
In the Wireless Transmitter Utility, enter the authentication code displayed by the camera. The camera will display an authentication code. Enter the authentication code in the dialog displayed by the Wireless Transmitter Utility and click [Next]. Complete the pairing process. When the camera displays a message stating that pairing is complete, press J.
Page 319
Check the connection. When a connection is established, the profile name will be displayed in green in the camera [Connect to computer] menu. If the profile name is not displayed in green, connect to the camera via the wireless network list on your computer. A wireless connection has now been established between the camera and the computer.
Page 320
Connecting in Infrastructure Mode The camera connects to a computer on an existing network (including home networks) via a wireless router. The computer can still connect to the Internet while connected to the camera. Before proceeding, check that the Wireless Transmitter Utility ( 314) is installed on the computer.
Page 321
Highlight [Search for Wi-Fi network] and press J. The camera will search for networks currently active in the vicinity and list them by name (SSID). “Easy Connect” To connect without entering an SSID or encryption key, press X in Step 4. Next, press J and choose from the options below. After connecting, proceed to Step 7.
Page 322
Choose a network. Highlight a network SSID and press J. The band on which each SSID operates is indicated by an icon. Encrypted networks are indicated by a h icon. If the selected network is encrypted (h), you will be prompted to enter the encryption key.
Page 323
Enter the encryption key. Press J and enter the encryption key for the wireless router. For more information, see the documentation for the wireless router. Press X when entry is complete. Press X again to initiate the connection. A message will be displayed for a few seconds when the connection is established.
Page 324
Obtain or select an IP address. Highlight one of the following options and press J. Option Description Select this option if the network is configured to supply the IP address [Obtain automatically. A “configuration complete” message will be displayed automatically] once an IP address has been assigned.
Page 325
Select the camera in the Wireless Transmitter Utility. Select the name displayed by the camera in Step 9 and click [Next]. In the Wireless Transmitter Utility, enter the authentication code displayed by the camera. The camera will display an authentication code. Enter the authentication code in the dialog displayed by the Wireless Transmitter Utility and click [Next].
Page 326
Complete the pairing process. When the camera displays a message stating that pairing is complete, press J. In the Wireless Transmitter Utility, click [Next]; you will be prompted to choose a destination folder. For more information, see online help for the Wireless Transmitter Utility.
Ending the Connection to the Computer You can end the connection by: turning the camera off, or selecting [End current connection] for [Connect to computer] > [Network settings] in the network menu. Access-Point Mode An error will occur if the computer’s wireless connection is disabled before the camera’s. Disable camera’s connection first.
Once the devices are paired, you will be able to connect to the computer from the camera. The Wireless Transmitter Utility is available for download from the Nikon Download Center. Check the version and system requirements and be sure to download the latest version.
Connecting to Computers via Ethernet Connect to computers via a third-party USB (Type C) to Ethernet adapter connected to the camera’s USB data connector. Before proceeding, check that the Wireless Transmitter Utility ( 328) is installed on the computer. Attach a third-party USB-to-Ethernet adapter to the camera’s USB data connector and then connect to the computer using an Ethernet cable.
Page 330
Highlight [Create profile] and press J. Name the new profile. To proceed to the next step without changing the default name, press X. Whatever name you choose will appear in the network menu [Connect to computer] > [Network settings] list. To rename the profile, press J. For information on text entry, see “Text Entry”...
Page 331
Obtain or select an IP address. Highlight one of the following options and press J. Option Description Select this option if the network is configured to supply the IP address [Obtain automatically. A “configuration complete” message will be displayed automatically] once an IP address has been assigned.
Page 332
Select the camera in the Wireless Transmitter Utility. Select the name displayed by the camera in Step 8 and click [Next]. In the Wireless Transmitter Utility, enter the authentication code displayed by the camera. The camera will display an authentication code. Enter the authentication code in the dialog displayed by the Wireless Transmitter Utility and click [Next].
Page 333
Complete the pairing process. When the camera displays a message stating that pairing is complete, press J. In the Wireless Transmitter Utility, click [Next]; you will be prompted to choose a destination folder. For more information, see online help for the Wireless Transmitter Utility.
Ending the Connection to the Computer You can end the connection by: turning the camera off, or selecting [End current connection] for [Connect to computer] > [Network settings] in the network menu. Computers: Connecting via Ethernet...
FTP Servers: Connecting via Wireless LAN The camera can connect to FTP servers via Wi-Fi (built-in wireless LAN). Connecting to Multiple Devices The camera can connect to only one type of device (computer, FTP server, or smart device) at a time. End the current connection before attempting to connect to a device of a different type.
Connecting to FTP Servers via Wireless LAN The camera can connect to FTP servers either by direct wireless link (access-point mode) or via a wireless router on an existing network, including home networks (infrastructure mode). FTP Servers Servers can be configured using standard FTP services—including IIS (Internet Information Services) —available with Windows 11 and Windows 10.
Page 337
Highlight [Create profile] and press J. Highlight [Connection wizard] and press 2. The connection wizard will launch. Manual Configuration Choose [Configure manually] to configure settings manually. Name the new profile. To proceed to the next step without changing the default name, press X.
Page 338
Highlight [Direct connection to computer] and press J. The camera SSID and encryption key will be displayed. Establish a connection to the camera. Windows: Click the wireless LAN icon in the taskbar. Select the SSID displayed by the camera in Step 5. When prompted to enter the network security key, enter the encryption key displayed by the camera in Step 5.
Page 339
Choose the server type. Highlight [FTP], [SFTP] (SSH FTP), or [FTPS] (FTP-SSL) and press J to display a dialog where you can choose a login method. Log in. Highlight one of the following options and press J. Option Description Select this option if the server does not require a user ID or password. [Anonymous This option can only be used with servers that are configured for login]...
Page 340
Choose a destination folder. Highlight one of the following options and press J. Option Description Select this option to select the server’s home folder as the destination [Home for pictures uploaded from the camera. A “setup complete” dialog will be folder] displayed if the operation is successful.
Page 341
Connecting in Infrastructure Mode The camera connects to an FTP server on an existing network (including home networks) via a wireless router. Create a host profile using the camera connection wizard. Tip: Infrastructure Mode Infrastructure mode supports connection to FTP servers on different networks. Select [Connect to FTP server] in the network menu, then highlight [Network settings] and press 2.
Page 342
Highlight [Connection wizard] and press 2. The connection wizard will launch. Manual Configuration Choose [Configure manually] to configure settings manually. Name the new profile. To proceed to the next step without changing the default name, press X. Whatever name you choose will appear in the network menu [Connect to FTP server] >...
Page 343
Highlight [Search for Wi-Fi network] and press J. The camera will search for networks currently active in the vicinity and list them by name (SSID). “Easy Connect” To connect without entering an SSID or encryption key, press X in Step 5. Next, press J and choose from the options below. After connecting, proceed to Step 8.
Page 344
Choose a network. Highlight a network SSID and press J. The band on which each SSID operates is indicated by an icon. Encrypted networks are indicated by a h icon. If the selected network is encrypted (h), you will be prompted to enter the encryption key.
Page 345
Enter the encryption key. Press J and enter the encryption key for the wireless router. For more information, see the documentation for the wireless router. Press X when entry is complete. Press X again to initiate the connection. A message will be displayed for a few seconds when the connection is established.
Page 346
Obtain or select an IP address. Highlight one of the following options and press J. Option Description Select this option if the network is configured to supply the IP address [Obtain automatically. A “configuration complete” message will be displayed automatically] once an IP address has been assigned.
Page 347
Enter the server address. Press J to enter the server URL or IP address. Press X when entry is complete. Press X again to connect to the FTP server. You will be prompted to choose a login method. FTP Servers: Connecting via Wireless LAN...
Page 348
Log in. Highlight one of the following options and press J. Option Description Select this option if the server does not require a user ID or password. [Anonymous This option can only be used with servers that are configured for login] anonymous login.
Page 349
Choose a destination folder. Highlight one of the following options and press J. Option Description Select this option to select the server’s home folder as the destination [Home for pictures uploaded from the camera. A “setup complete” dialog will be folder] displayed if the operation is successful.
Ending the Connection to the FTP Server You can end the connection by: turning the camera off, or selecting [End current connection] for [Connect to FTP server] > [Network settings] in the network menu. Access-Point Mode An error will occur if the FTP server’s wireless connection is disabled before the camera’s. Disable camera’s connection first.
FTP Servers: Connecting via Ethernet A USB (Type C) to Ethernet adapter (available separately from third-party sources) is required for Ethernet connections. Be sure to connect the adapter to the camera’s USB data connector. The following USB-to-Ethernet adapters have been tested and approved for use: Anker A83130A1 PowerExpand USB‑C to Gigabit Ethernet adapters Anker A83130A2 PowerExpand USB‑C to Gigabit Ethernet adapters Note that USB-to-Ethernet adapters will not function when connected to the camera’s USB Power...
Connecting to FTP Servers via Ethernet Connect to FTP servers via a third-party USB (Type C) to Ethernet adapter connected to the camera’s USB data connector. FTP Servers Servers can be configured using standard FTP services—including IIS (Internet Information Services) —available with Windows 11 and Windows 10.
Page 353
Select [USB-LAN] for [USB data connection] in the network menu. Select [Connect to FTP server] in the network menu, then highlight [Network settings] and press 2. Highlight [Create profile] and press J. Highlight [Connection wizard] and press 2. The connection wizard will launch. Manual Configuration Choose [Configure manually] to configure settings manually.
Page 354
Name the new profile. To proceed to the next step without changing the default name, press X. Whatever name you choose will appear in the network menu [Connect to FTP server] > [Network settings] list. To rename the profile, press J. For information on text entry, see “Text Entry”...
Page 355
Choose the server type. Highlight [FTP], [SFTP] (SSH FTP), or [FTPS] (FTP-SSL) and press J to display a dialog where you can enter the server address. Enter the server address. Press J to enter the server URL or IP address. Press X when entry is complete.
Page 356
Log in. Highlight one of the following options and press J. Option Description Select this option if the server does not require a user ID or password. [Anonymous This option can only be used with servers that are configured for login] anonymous login.
Page 357
Choose a destination folder. Highlight one of the following options and press J. Option Description Select this option to select the server’s home folder as the destination [Home for pictures uploaded from the camera. A “setup complete” dialog will be folder] displayed if the operation is successful.
Ending the Connection to the FTP Server You can end the connection by: turning the camera off, or selecting [End current connection] for [Connect to FTP server] > [Network settings] in the network menu. FTP Servers: Connecting via Ethernet...
What You Can Do When the Camera Is Connected to a Computer or FTP Server Ethernet and wireless LAN connections can be used to upload pictures or control the camera remotely. Uploading Pictures Pictures can be selected for upload during playback. They can also be uploaded automatically as they are taken.
Page 360
Caution: Access Point Mode Select a host profile and enable camera Wi-Fi before connecting. Destination Folders for Upload to a Computer By default, pictures are uploaded to the following folders: Windows: \Users\(user name)\Pictures\Wireless Transmitter Utility macOS: /Users/(user name)/Pictures/Wireless Transmitter Utility The destination folder can be selected using the Wireless Transmitter Utility.
Page 361
Removing Upload Marking Repeat Steps 2–3 to remove upload marking from selected pictures. To remove upload marking from all pictures, select [Connect to computer] or [Connect to FTP server] in the network menu and choose [Options] > [Deselect all?]. Tip: Filtering Pictures for Upload The [Filtered playback] item in the playback i menu can be used to display only pictures that meet chosen criteria ( 239).
Page 362
Uploading Photos as They Are Taken To upload new photos as they are taken, select [Connect to computer] or [Connect to FTP server] in the network menu and choose [ON] for [Options] > [Auto upload]. Upload begins only after the photo has been recorded to the memory card. Be sure a memory card is inserted in the camera.
Page 363
The “Connect to Computer”/“Connect to FTP Server” Upload Status Display The [Connect to computer] and [Connect to FTP server] displays show the following: Status: The status of the connection to the host. The profile name is displayed in green when a connection is established.
Page 364
Loss of Signal Wireless transmission may be interrupted if the signal is lost. Upload of pictures with upload marking can be resumed by turning the camera off and then on again once the signal has been re-established. Caution: During Upload Do not remove the memory card or disconnect the Ethernet cable during upload.
Camera Control The camera can be controlled from a computer running Camera Control Pro 2 (available separately) or free NX Tether software. Photos can be saved directly to the computer instead of to the memory card and can consequently be taken even when no memory card is inserted in the camera. You will still need to insert a memory card when filming videos.
Page 366
The “Connect to Computer” Camera Control Display The [Connect to computer] display shows the following: Status: The status of the connection to the host. The profile name is displayed in green when a connection is established. Errors are also displayed here ( 367).
Troubleshooting Wireless LAN and Ethernet Connections Refer to this section for information on errors involving wireless LAN and Ethernet connections. For information on the Wireless Transmitter Utility, see the utility’s online help. Problems and Solutions Solutions to some common issues are listed below. Problem Solution Connection settings require adjustment.
Error Codes The following messages and error codes may be displayed if an error occurs while the camera is connected to an FTP server via Ethernet or wireless LAN. ● [Wireless Error.] Error code Solution Confirm that the device to which you are attempting to connect is on. Err.11 Check the SSID ( 775).
Page 369
● [FTP Error.] Error code Solution Err.31 Check that the FTP server address is correct ( 775). Err.32 Check that the login name and password are correct ( 775). Err.34 Check that the destination folder name is correct ( 775). Err.35 Confirm that the destination folder is not write-protected.
Connecting to Other Cameras What Inter-camera Connections Can Do for You Camera-Based Remote Photography (Synchronized Release) A master camera can be used to release the shutters on up to ten remote cameras in the same group ( 371). Clock Synchronization (Synchronize Date and Time) Synchronize the clocks on multiple cameras via a network (...
Synchronized Release Configuring and Using Synchronized Release Follow the steps below to create host profiles for synchronized release. Each camera saves the pictures it takes to its own memory card. Repeat the process to create identical profiles for each camera. Wireless LAN To create host profiles when connecting via wireless LAN: Select [Connect to other cameras] in the network menu,...
Page 372
Highlight [Search for Wi-Fi network] and press J. The camera will search for networks currently active in the vicinity and list them by name (SSID). “Easy Connect” To connect without entering an SSID or encryption key, press X in Step 4. Next, press J and choose from the options below.
Page 373
Choose a network. Highlight a network SSID and press J. The band on which each SSID operates is indicated by an icon. Encrypted networks are indicated by a h icon. If the selected network is encrypted (h), you will be prompted to enter the encryption key.
Page 374
Enter the encryption key. Press J and enter the encryption key for the wireless router. For more information, see the documentation for the wireless router. Press X when entry is complete. Press X again to initiate the connection. A message will be displayed for a few seconds when the connection is established.
Page 375
Obtain or select an IP address. Highlight one of the following options and press J. Option Description Select this option if the network is configured to supply the IP address automatically. A “configuration complete” message will be displayed [Obtain once an IP address has been assigned. automatically] It is recommended that you note the remote camera IP address, as you will need it in subsequent steps.
Page 376
Highlight [Master/remote] and press 2. Choose a role for each camera from “master” and “remote”. [Master camera]: Pressing the shutter-release button on the master camera releases the shutters on the remote cameras. Each group can have only one master. If the group has multiple master cameras, only the first to connect to the network will actually serve in that capacity.
Page 377
Enter the remote camera IP address. Enter the remote camera IP address you noted in Step 7. Rotate the main command dial to highlight segments. Press 4 or 2 to change the highlighted segment and press J to save changes. Press X to add the remote camera to the master camera remote camera list and establish a connection.
Page 378
Take pictures. A k icon appears in the master camera shooting display together with the number of remote cameras connected. Pressing the shutter-release button on the master camera releases the shutters on the remote cameras. Connection Errors In the event of remote camera connection errors, the remote camera count in the master camera shooting display will turn red and instead show the number of remote cameras that failed to connect.
Page 379
Ethernet Follow the steps below to create host profiles for Ethernet connections. A USB (Type C) to Ethernet adapter (available separately from third-party sources) is required for Ethernet connections. Be sure to connect the adapter to the camera’s USB data connector. The following USB-to-Ethernet adapters have been tested and approved for use: Anker A83130A1 PowerExpand USB‑C to Gigabit Ethernet adapters Anker A83130A2 PowerExpand USB‑C to Gigabit Ethernet adapters...
Page 380
Select [Connect to other cameras] in the network menu, then highlight [Network settings] and press 2. Highlight [Create profile] and press J. Name the new profile. To display IP address options without changing the default name, press X. Whatever name you choose will appear in the network menu [Connect to other cameras] >...
Page 381
Obtain or select an IP address. Highlight one of the following options and press J. Option Description Select this option if the network is configured to supply the IP address automatically. A “configuration complete” message will be displayed [Obtain once an IP address has been assigned. automatically] It is recommended that you note the remote camera IP address, as you will need it in subsequent steps.
Page 382
Repeat Steps 3 through 9 for the remaining cameras. To configure another Z 8 for use as a remote camera, repeat Steps 2 through 9. When configuring remote cameras, be sure to select [Remote camera] in Step 9.
Page 383
Enter the remote camera IP address. Enter the remote camera IP address you noted in Step 6. Rotate the main command dial to highlight segments. Press 4 or 2 to change the highlighted segment and press J to save changes. Press X to add the remote camera to the master camera remote camera list and establish a connection.
Page 384
Take pictures. A k icon appears in the master camera shooting display together with the number of remote cameras connected. Pressing the shutter-release button on the master camera releases the shutters on the remote cameras. Connection Errors In the event of remote camera connection errors, the remote camera count in the master camera shooting display will turn red and instead show the number of remote cameras that failed to connect.
Page 385
Tip: Suspending Synchronized Release To temporarily disable synchronized release without ending the camera’s connection to the network, select [OFF] for [Connect to other cameras] > [Synchronized release] in the network menu. Tip: Viewing Remote Camera Status To view remote camera status, highlight [Remote camera list] on the master camera and press 2.
Synchronizing Camera Clocks When the cameras are connected to the network using [Connect to other cameras] in the network menu, the clocks on all cameras in the current group connected can be set to the time and date reported by the master camera. Synchronization applies to all options in the setup menu [Time zone and date] display.
Flash Photography “On-Camera” Versus “Remote” You can take pictures using an optional flash unit mounted on the camera accessory shoe or one or more remote flash units. When using a flash, select [OFF] for [Silent mode] in the setup menu. Camera-Mounted Flash Units Take pictures using a flash unit mounted on the camera.
Using an On-Camera Flash Mount a flash unit on the camera accessory shoe. See the documentation supplied with each Speedlight for information on mounting the unit on the camera. Turn on the camera and flash unit. The flash will begin charging; the flash-ready indicator (c) will appear in the shooting display when charging is complete.
Page 389
Shutter Speed Shutter speed can be set as follows when an optional flash unit is used: Shooting mode Shutter speed * P, A Set automatically by camera (¹⁄₂₀₀ s–¹⁄₆₀ s) ¹⁄₂₀₀ s–30 s ¹⁄₂₀₀ s–30 s, Bulb, Time Shutter speed may be set as slow as 30 s if slow sync, slow rear-curtain sync, or slow sync with red-eye reduction is selected for flash mode.
Page 390
Flash Control When an optional flash unit that supports the Nikon Creative Lighting System is attached and set to TTL, the camera uses monitor pre-flashes for balanced or standard “i-TTL fill-flash” flash control. i-TTL flash control is not available with flash units that do not support the Nikon Creative Lighting System.
Flash Control Mode When a flash unit that supports unified flash control (an SB‑5000, SB‑500, SB‑400, or SB‑300; 392) is mounted on the camera, the flash control mode, flash level, and other flash settings can be adjusted using the [Flash control] > [Flash control mode] item in the photo shooting menu.
Page 392
Unified Flash Control Unified flash control allows the camera and flash unit to share settings. Changes to flash settings made with either the camera or flash unit are reflected on both devices, as are changes made using optional Camera Control Pro 2 software. The flash unit must support unified flash control. Flash Control Mode...
Flash Modes The flash mode can be selected via the [Flash mode] item in the photo shooting menu. The options available vary with the shooting mode. Option Description Available in This mode is recommended in most situations. In modes [Fill flash] P and A, shutter speed will automatically be set to (front-curtain P, S, A, M...
Page 394
Option Description Available in The flash fires just before the shutter closes, creating the effect of a stream of light behind moving light sources. Selecting mode P or A after choosing this option sets [Rear-curtain the flash mode to slow sync. P, S, A, M sync] Note that photos may be prone to blurring due to...
Flash Compensation Flash compensation is used to deliberately alter flash output, for example in order to change the brightness of the subject relative to the background. Flash output can be increased to make the main subject appear brighter, reduced to prevent glare, or otherwise fine-tuned to produce the desired result.
FV Lock This feature is used to lock flash output for optional CLS-compatible flash units, letting you take multiple photos or recompose shots without changing the flash level. Your subject need not be in the center of the frame, giving you more freedom when composing shots. Flash output is adjusted automatically for any changes in ISO sensitivity and aperture.
Page 397
Lock flash level. After confirming that the flash-ready indicator (c) appears in the shooting display, press the [FV lock] control; the flash unit will emit a monitor pre-flash to determine the appropriate flash level. Flash output will lock and an FV lock icon (r) will appear in the shooting display.
Remote Flash Photography What Is Remote Flash Photography? Take pictures with one or more remote flash units using wireless flash control (Advanced Wireless Lighting, or AWL). For information on using a flash unit mounted on the camera accessory shoe, see “Using an On-Camera Flash”...
A WR‑A10 adapter is required when using the WR‑R10. Be sure to update the firmware for the optional WR‑R10 wireless remote controller to version 3.0 or later before using radio AWL. Information on performing firmware updates is available via the Nikon website for your country or region.
Page 400
C: Choose a channel for the WR‑R11a/WR‑R10. Set the WR‑R11a/WR‑R10 channel selector to the desired channel. C: Choose a link mode for the WR‑R11a/WR‑R10. Select [Wireless remote (WR) options] > [Link mode] in the camera setup menu and choose from the following options: Option Description The camera connects only to devices with which it has previously been paired.
Page 401
f: Establish a wireless connection between the WR‑R11a/WR‑R10 and the remote flash units. Set the remote units to radio AWL remote mode. Set the remote units to the channel you selected for the WR‑R11a/WR‑R10 in Step 3. Pair each of the remote units with the WR‑R11a/WR‑R10 according to the option selected in Step 4: [Pairing]: Initiate pairing on the remote unit and press the WR‑R11a/WR‑R10 pairing button.
Page 402
Listing Remote Flash Units To view the flash units currently controlled using radio AWL, select [Flash control] > [Radio remote flash info] in the camera photo shooting menu. The identifier (remote flash unit name) for each unit can be changed using flash unit controls. Connected flash unit Group Flash-ready indicator...
Remote Flash Photography Settings are adjusted using [Flash control] > [Remote flash control] in the photo shooting menu. Choose a remote flash control mode and take pictures as described below. Group Flash Select this item if you want to adjust settings separately for the flash units in each group. C: Select [Group flash] for [Flash control] >...
Page 404
C: Choose a flash control mode and flash level. Choose a flash control mode and flash level for the flash units in each group. The following options are available: Option Description i-TTL flash control. Auto aperture. Available only with compatible flash units. Choose the flash level manually.
Page 405
Tip: Flash Info Group flash options can be viewed using the [Flash info] item in the i menu, which can be added to the menu using Custom Setting f1 [Customize i menu]. Quick Wireless Control Select this item to control the relative balance between the remote flash units in groups A and B and adjust flash output for group C.
Page 406
C: Adjust quick wireless control settings. Choose the balance between groups A and B. Adjust flash compensation for groups A and B. Adjust settings for group C: Select [M] to enable or [– –] to disable the units in group When [M] is selected, the units in group C will fire at the chosen output.
Page 407
Tip: Flash Info Quick wireless control settings can be viewed using the [Flash info] item in the i menu, which can be added to the menu using Custom Setting f1 [Customize i menu]. Remote Repeating The flash units fire repeatedly while the shutter is open, producing a multiple-exposure effect. C: Select [Remote repeating] for [Flash control] >...
Page 408
C: Adjust remote repeating options. Adjust “output”, “times”, and “frequency”. Enable or disable selected groups. Select [ON] to enable or [– –] to disable the selected group. f: Group the remote flash units. Choose a group (A–F) for each of the remote flash units. The master flash can control up to 18 flash units in any combination.
Adding a Shoe-Mounted Flash Unit Radio-controlled flash units ( 399) can be combined with any of the following flash units mounted on the camera accessory shoe: SB‑5000: Before attaching the flash unit, set it to radio-controlled master flash mode (a d icon will appear at the top left corner of the display) and choose group or remote-repeating flash control.
Optical AWL Remote flash units can be controlled via optical signals from an optional flash unit mounted on the camera accessory shoe and functioning as a master flash (optical AWL). For information on compatible flash units, see “Features Available with CLS-Compatible Flash Units”...
Using Optical AWL with the SB‑5000 or SB‑500 Mount the flash unit on the camera accessory shoe. Select [Optical AWL] for [Flash control] > [Wireless flash options] in the photo shooting menu and choose a remote flash control mode (the SB‑500 supports only [Group flash]). The procedure for adjusting settings and taking pictures in each mode is described below.
Page 412
C: Adjust flash output and choose the channel and flash control mode. Choose the flash control mode and flash level for the master flash and the remote flash units in each group. The following options are available: Option Description i-TTL flash control. Auto aperture.
Page 413
C/f: Compose the shot and arrange the flash units. See the documentation provided with the flash units for more information. Test-fire the units and confirm that they are functioning normally. To test-fire the units, use the [Test flash] item in the i menu, which can be added to the menu using Custom Setting f1 [Customize i menu].
Page 414
C: Adjust quick wireless control settings. Choose the balance between groups A and B. Adjust flash compensation for groups A and B. Adjust settings for group C: Select [M] to enable or [– –] to disable the units in group When [M] is selected, the units in group C will fire at the chosen output.
Page 415
C/f: Compose the shot and arrange the flash units. See the documentation provided with the flash units for more information. Test-fire the units and confirm that they are functioning normally. To test-fire the units, use the [Test flash] item in the i menu, which can be added to the menu using Custom Setting f1 [Customize i menu].
Page 416
C: Adjust remote repeating options. Adjust “output”, “times”, and “frequency”. Enable or disable selected groups. Select [ON] to enable or [– –] to disable the selected group. Choose the channel. For [Channel], choose the channel (1–4) the master flash will use for optical remote flash control. If the remote flash units include an SB‑500, you must choose Channel [3].
Page 417
C/f: Take the photograph after confirming that the flash-ready lights for all flash units are lit. Optical AWL Position the sensor windows on the remote flash units to pick up the light from the master flash. Particular care is required if the master flash is mounted on a hand-held camera. Be sure that direct light or strong reflections from the remote flash units do not enter the camera lens (in [TTL] mode) or the photocells on the remote flash units ([qA] mode).
The Photo Shooting Menu Menu Items and Defaults To view the photo shooting menu, select the C tab in the camera menus. The options in the photo shooting menu are listed below, together with their default settings. [Shooting menu bank]: A [Extended menu banks]: OFF [Storage folder] [Rename]: NCZ_8...
Page 419
[Manage Picture Control]: — [Set Picture Control (HLG)]: Standard [Color space]: sRGB [Active D-Lighting]: Off [Long exposure NR]: OFF [High ISO NR]: Normal [Vignette control]: Normal [Diffraction compensation]: ON [Auto distortion control]: ON [Skin softening]: Off [Portrait impression balance]: Off [Photo flicker reduction]: OFF [High-frequency flicker reduction]: Off [Metering]: Matrix metering...
Page 420
[Exposure smoothing]: ON [Interval priority]: OFF [Focus before each shot]: OFF [Options]: Off [Starting storage folder] [New folder]: U [Reset file numbering]: U [Time-lapse video] [Interval]: 5 s [Shooting time]: 25 min. [Exposure smoothing]: ON [Choose image area]: FX [Video file type]: H.265 8-bit (MOV) [Frame size/frame rate]: 3840×2160;...
Shooting Menu Bank G button U C photo shooting menu Photo shooting and video recording menu options are stored in one of four banks (banks “A” through “D”) that can be selected using [Shooting menu bank]. With the exceptions noted below, changes to settings made while one bank is selected are not applied to the remaining banks.
Renaming Shooting Menu Banks A descriptive caption can be added to the bank name (“A”, “B”, “C”, or “D”) by highlighting the bank, pressing 2, and selecting [Rename]. Captions can be up to 20 characters long. Copying Shooting Menu Banks To create a copy of a shooting menu bank, highlight the bank, press 2, select [Copy], and choose a destination for the copy.
Extended Menu Banks G button U C photo shooting menu Select [ON] to include exposure settings in the information recorded in each of the four shooting menu banks. Changes to exposure settings will be stored in the bank currently selected for [Shooting menu bank].
Storage Folder G button U C photo shooting menu Choose the folder in which subsequent pictures will be stored. Folder Folder number Folder name “Storage Folder” Changes to [Storage folder] made in the photo shooting menu apply in the video recording menu and vice versa. Renaming Folders The default folder name, which appears after the folder number, is “NCZ_8”.
Select Folder by Number The folder in which subsequent pictures will be stored can be selected by number. If a folder with the specified number does not already exist, a new folder will be created. Choose [Select folder by number]. Highlight [Select folder by number] and press 2 to display the [Select folder by number] dialog.
Select Folder from List To choose from a list of existing folders: Choose [Select folder from list]. Highlight [Select folder from list] and press 2 to display the [Select folder from list] dialog. Highlight a folder. Press 1 or 3 to highlight a folder. Select the highlighted folder.
File Naming G button U C photo shooting menu Pictures are saved using file names consisting of “DSC_” followed by a four-digit number and a three-letter extension. [File naming] is used to select three letters to replace the “DSC” portion of the file name. For information on text entry, see “Text Entry” ( 67).
Primary Slot Selection G button U C photo shooting menu Choose which of the CFexpress/XQD and SD memory card slots functions as the primary slot when two memory cards are inserted. Option Description [CFexpress/XQD card slot] The CFexpress/XQD card slot functions as the primary slot. [SD card slot] The SD card slot functions as the primary slot.
Secondary Slot Function G button U C photo shooting menu Choose the role played by the card in the secondary slot when two memory cards are inserted in the camera. Option Description The card in the secondary slot is used only when the card in the primary [Overflow] slot is full.
Page 430
Option Description This option is available when [HLG] is selected for tone mode. Two HEIF copies are recorded, one to each memory card. The copy saved to the card in the primary slot is recorded at the image quality and size selected in the photo shooting menu. The copy saved [HEIF primary to the card in the secondary slot is saved at an image quality of [JPEG/ - HEIF...
Deleting Copies When deleting pictures recorded using [Backup], [RAW primary - JPEG secondary], [JPEG primary - JPEG secondary], [RAW primary - HEIF secondary], or [HEIF primary - HEIF secondary], you have the choice of erasing either both copies or only the copy on the card in the current slot. Pressing O (Q) when a picture created using either of these options is highlighted during playback displays a confirmation message.
Image Area G button U C photo shooting menu Adjust image area settings. For more information, see “Adjusting Image Area Settings” ( 99), part of the section on “Image Recording Options (Image Area, Quality, and Size)” in the “Shooting Settings” chapter. Image Area...
Tone Mode G button U C photo shooting menu The camera offers a choice of two tone modes: [SDR] and [HLG]. Option Description This mode supports a normal range of brightnesses (dynamic range). Pictures taken while [SDR] this option is selected are stored in JPEG format (extension “*.JPG”). This mode supports HDR (high dynamic range).
Page 434
HLG (HEIF) photos can be viewed and edited using NX Studio computer software. NX Studio can be downloaded free of charge from the Nikon Download Center. Some of the options available for editing HLG photos are more limited than is the case with photos shot with [SDR] selected for tone mode.
Image Quality G button U C photo shooting menu Choose a file format for photographs. For more information, see “Adjusting Image Quality” ( 101), part of the section on “Image Recording Options (Image Area, Quality, and Size)” in the “Shooting Settings” chapter. Image Quality...
Image Size Settings G button U C photo shooting menu Choose the size, in pixels, of pictures recorded with the camera. For more information, see “Choosing an Image Size” ( 103), part of the section on “Image Recording Options (Image Area, Quality, and Size)”...
RAW Recording G button U C photo shooting menu Choose a compression type for NEF (RAW) photographs. In descending order by the size of the files produced, the options are: [Lossless compression], [High efficiencym], and [High efficiency]. [High efficiencym] produces pictures that compare favorably in quality to those produced by [Lossless compression] and are higher in quality than those produced by [High efficiency].
ISO Sensitivity Settings G button U C photo shooting menu Adjust ISO sensitivity settings for photographs. Option Description Choose from settings of ISO 64 to 25600; the camera also supports settings [ISO below ISO 64 by about 0.3, 0.7, and 1 EV (ISO 32 equivalent) and above ISO sensitivity] 25600 by about 0.3, 0.7, 1, and 2 EV (ISO 102400 equivalent).
White Balance G button U C photo shooting menu Adjust white balance to match the color of the light source. For more information, see “White Balance” 143) in the “Shooting Settings” chapter. White Balance...
Set Picture Control G button U C photo shooting menu Choose image processing (“Picture Control”) options for new photos according to the scene or your creative intent. For more information, see “Picture Controls” ( 175) in the “Shooting Settings” chapter. Set Picture Control...
Manage Picture Control G button U C photo shooting menu Save modified Picture Controls as custom Picture Controls. For more information, see “Custom Picture Controls” ( 181) in the “Picture Controls” section of the “Shooting Settings” chapter. Manage Picture Control...
Set Picture Control (HLG) G button U C photo shooting menu Choose image processing (“Picture Control”) options for photos taken with [HLG] selected for tone mode. Option Description Standard processing for balanced results. Recommended for most [Standard] situations. [Monochrome] Take monochrome photographs. Choose for photographs that will later be extensively processed or [Flat] retouched.
Page 443
Adjust settings. Press 1 or 3 to highlight settings. Press 4 or 2 to choose a value in increments of 1, or rotate the sub-command dial to choose a value in increments of 0.25. The options available vary with the Picture Control selected. To quickly adjust levels for balanced [Sharpening], [Mid- range sharpening], and [Clarity], highlight [Quick sharp] and press 4 or 2.
Page 444
HLG Picture Control Settings Option Description Use [Quick sharp] to quickly adjust levels for balanced [Sharpening], [Quick sharp] [Mid-range sharpening], and [Clarity]. These parameters can also be adjusted individually. [Sharpening] Control the sharpness of details and outlines. [Mid-range Adjust the sharpness of patterns and lines in the range between ...
Page 445
The j Indicator The j indicator under the value display in the Picture Control setting menu indicates the previous value for the setting. “Filter Effects” Choose from the following [Filter effects]: Option Description * [Y] (yellow) These options enhance contrast and can be used to tone down the brightness of * [O] (orange) the sky in landscape photographs.
Color Space G button U C photo shooting menu The color space determines the gamut of colors available for color reproduction. [sRGB] is recommended for general-purpose printing and display. With a broader gamut of colors than [sRGB], [Adobe RGB] is a better choice for professional publication and commercial printing. Caution: Color Space The selected color space may be overwritten when pictures are opened in third-party software.
Active D‑Lighting G button U C photo shooting menu Preserve details in highlights and shadows, creating pictures with natural contrast. Use for high- contrast scenes, for example when photographing brightly-lit outdoor scenery through a door or window or taking pictures of shaded subjects on a sunny day. Active D-Lighting is most effective when used with matrix metering.
Page 448
The option currently selected is shown by an icon in the display during shooting. Cautions: Active D-Lighting Depending on the subject, “noise” in the form of randomly-spaced bright pixels, fog, or lines may appear in photos taken with Active D-Lighting. In mode M, [Y Auto] is equivalent to [Q Normal].
Long Exposure NR G button U C photo shooting menu Select [ON] to reduce “noise” (bright spots or fog) in photographs taken at shutter speeds slower than 1 s. Long-exposure noise reduction is performed after the photo is taken. During processing, the message, “[Performing noise reduction]” will appear in the shooting display and “Job NR” will flash in the control panel.
High ISO NR G button U C photo shooting menu Photographs taken at high ISO sensitivities can be processed to reduce “noise” (randomly-spaced bright pixels). Option Description [High] Reduce noise in photographs taken at all ISO sensitivities. The higher the sensitivity, [Normal] the greater the effect. Choose the amount of noise reduction performed from (in order from high to low) [High], [Normal], and [Low].
Vignette Control G button U C photo shooting menu Vignette control reduces “vignetting”—a drop in brightness at the edges of a photograph—by an amount that varies from lens to lens. Its effects are most noticeable at maximum aperture. Option Description [High] Choose the amount of vignette control performed from (in order from high to [Normal] low) [High], [Normal], and [Low].
Diffraction Compensation G button U C photo shooting menu Select [ON] to reduce diffraction at small apertures (high f-numbers). Diffraction Compensation Changes to [Diffraction compensation] in the photo shooting menu apply in the video recording menu and vice versa. Diffraction Compensation...
Auto Distortion Control G button U C photo shooting menu Select [ON] as required to reduce barrel distortion when shooting with wide-angle lenses and to reduce pin-cushion distortion when shooting with long lenses. Note that [ON] may be selected automatically with some lenses, in which case this item will be grayed out and unavailable. Auto Distortion Control Changes to [Auto distortion control] in the photo shooting menu apply in the video recording menu and vice versa.
Skin Softening G button U C photo shooting menu Pictures taken when the face of a human portrait subject is detected will automatically be processed to soften the subject’s complexion. Option Description [High] Choose the amount of skin softening performed from (in order from high to low) [High], [Normal], and [Low].
Portrait Impression Balance G button U C photo shooting menu Fine-tune hue and brightness settings for human portrait subjects and save the results for application during shooting as [Mode 1], [Mode 2], or [Mode 3]. Creating Portrait Impression Balance Modes Select [Portrait impression balance] in the photo shooting menu.
Save changes. Press J to save changes and exit to the menus. Modes that have been altered from default values are indicated by asterisks (“U”). Repeat Steps 1 through 4 to create additional modes. Applying Saved Modes To enable portrait impression balance during shooting, select the desired mode ([Mode 1] through [Mode 3]) for [Portrait impression balance] in the photo shooting menu.
Photo Flicker Reduction G button U C photo shooting menu Selecting [ON] reduces the effects of flicker from such light sources as fluorescent or mercury-vapor lamps. Flicker can cause uneven exposure or (in photographs taken in continuous release modes) inconsistent exposure or coloration. If flicker reduction does not produce the desired results, turn the camera off and aim it at the subject or light source before turning it on again.
Page 458
“Photo Flicker Reduction” Flicker reduction may slightly delay shutter response. Flicker reduction can detect flicker at 100 and 120 Hz (associated respectively with AC power supplies of 50 and 60 Hz). The desired results may not be achieved if the frequency of the power supply changes during burst photography.
High-Frequency Flicker Reduction G button U C photo shooting menu Selecting [On (shutter speed fine-tuning)] allows shutter speeds between ¹⁄₈₀₀₀ and ¹⁄₃₀ s to be adjusted in smaller increments in modes S and M, letting speeds that keep flicker to a minimum be found by viewing the preview in the shooting display. Flicker may cause banding in pictures taken under high-frequency LED lighting or in shots that include monitors with high-frequency LED displays.
Page 460
Cautions: High-Frequency Flicker Reduction The effects of flicker in the shooting display may differ from those seen in photographs. We recommend that you take test shots to identify the shutter speed that minimizes flicker and banding. Exposure maintenance is disabled while high-frequency flicker reduction is in effect, even when [Shutter speed] is selected for Custom Setting b7 [Keep exp.
Metering G button U C photo shooting menu Metering determines how the camera sets exposure. Option Description The camera meters a wide area of the frame and sets exposure according to [Matrix tone distribution, color, composition, and distance for results close to those metering] seen by the naked eye.
Flash Control G button U C photo shooting menu Adjust settings for wireless remote flash units or optional flash units mounted on the camera accessory shoe. For information on adjusting settings for optional flash units mounted on the camera accessory shoe, see “Using an On- Camera Flash”...
Option Description [TTL] Flash output is adjusted automatically in response to shooting conditions. Light from the flash is reflected from the subject to an auto external flash [Auto external flash] sensor and flash output adjusted automatically. [Distance-priority Choose the distance to the subject; flash output will be adjusted manual] automatically.
Remote Flash Control Choose the remote flash control mode. Flash options can be adjusted in the flash control display; the options available vary with the option selected for [Remote flash control]. Option Description Choose a separate flash control mode for each group of remote flash [Group flash] units ( 403,...
Flash Mode G button U C photo shooting menu Choose a flash mode for camera-mounted or remote optional flash units. For more information, see “Flash Modes” ( 393) in “Flash Photography”. Flash Mode...
Flash Compensation G button U C photo shooting menu Flash compensation is used to deliberately alter the output of optional flash units, for example in order to change the brightness of the subject relative to the background. Flash output can be increased to make the main subject appear brighter, reduced to prevent glare, or otherwise fine-tuned to produce the desired result ( ...
Focus Mode G button U C photo shooting menu Control how the camera focuses. For more information, see “Focus Mode” ( 105), part of the section on “Focus” in the “Shooting Settings” chapter. Focus Mode...
AF-Area Mode G button U C photo shooting menu Choose how the camera selects the focus point for autofocus. For more information, see “AF-Area Mode” ( 107), part of the section on “Focus” in the “Shooting Settings” chapter. AF-Area Mode...
AF Subject Detection Options G button U C photo shooting menu Choose the type of subject to which the camera gives priority when focusing using autofocus. For more information, see “Choosing a Subject Type for Autofocus” ( 111), part of the section on “Focus” in the “Shooting Settings”...
Vibration Reduction G button U C photo shooting menu Choose whether to enable vibration reduction. The options available vary with the lens. Option Description [Normal] Choose for enhanced vibration reduction when photographing static subjects. Choose when photographing athletes and other subjects that are moving [Sport] rapidly and unpredictably.
Auto Bracketing G button U C photo shooting menu Bracketing automatically varies exposure, flash level, Active D-Lighting (ADL), or white balance slightly with each shot, “bracketing” the current value. For more information, see “Bracketing” ( 162) in the “Shooting Settings” chapter. Auto Bracketing...
Multiple Exposure G button U C photo shooting menu Record two to ten NEF (RAW) exposures as a single photograph. Option Description [On (series)]: Take a series of multiple exposures. To end multiple exposure [Multiple photography, select [Multiple exposure mode] again and choose [Off]. exposure [On (single photo)]: End multiple exposure photography after creating a mode]...
Option Description [Save [ON]: Save both the multiple exposure and the shots that make it up; the individual pictures are saved in NEF (RAW) format. pictures [OFF]: Discard the individual shots and save only the multiple exposure. (RAW)] [Overlay If [ON] is selected, earlier exposures will be superimposed on the view through shooting] the lens.
Page 474
Choose a value for [Number of shots] (number of exposures). Highlight [Number of shots] and press 2. Choose the number of exposures using 1 or 3 and press J. Select an [Overlay mode]. Highlight [Overlay mode] and press 2. Highlight an option using 1 or 3 and press J. Choose a setting for [Save individual pictures (RAW)].
Page 475
Start shooting. Take the selected number of shots. If you used [Select first exposure (RAW)] to select an existing NEF (RAW) picture as the first exposure in Step 7, shooting will start from the second exposure. Once you have taken the selected number of shots, the pictures will be overlaid to create a multiple exposure.
Page 476
The i Menu Pictures can be viewed by pressing the K button while a multiple exposure is in progress. The most recent shot in the current multiple exposure is indicated by a $ icon; pressing the i button when this icon is present displays the multiple exposure i menu.
Page 477
Cautions: Multiple Exposure If you use the menus or view pictures in the display while shooting a multiple exposure, remember that shooting will end and the multiple exposure will be recorded if no operations are performed for about 40 seconds (or in the case of menus, about 90 seconds). The time available to record the next exposure can be extended by choosing longer times for Custom Setting c3 [Power off delay] >...
Page 478
Ending Multiple Exposures To end a multiple exposure before the specified number of exposures have been taken, select [Off] for multiple exposure mode. A multiple exposure will be created from the exposures that have been recorded to that point (if [Average] is selected for [Overlay mode], gain will be adjusted to reflect the number of exposures actually recorded).
HDR Overlay G button U C photo shooting menu Used with high contrast subjects, High Dynamic Range (HDR) preserves details in highlights and shadows by combining two shots taken at different exposures. Use with high-contrast scenes and other subjects to preserve a wide range of details, from highlights to shadows. Option Description [On (series)]: Take a series of HDR photographs.
Taking HDR Photographs We recommend that you use matrix metering when shooting with HDR. Highlight [HDR overlay] in the photo shooting menu and press 2. Select an [HDR mode]. Highlight [HDR mode] and press 2. Highlight one of the following options using 1 or 3 and press J.
Page 481
Choose an [HDR strength]. Highlight [HDR strength] and press 2. Highlight an option using 1 or 3 and press J. If [Auto] is selected, the camera will automatically adjust HDR strength to suit the scene. Choose a setting for [Save individual pictures (RAW)]. Choose [ON] to save each of the individual shots used to create the HDR picture;...
Page 482
Cautions: HDR Photography The edges of the picture will be cropped out. The desired results may not be achieved if the camera or subject moves during shooting. Use of a tripod is recommended. Depending on the scene, you may notice shadows around bright objects or halos around dark objects.
Interval Timer Shooting G button U C photo shooting menu Take photographs at the selected interval until the specified number of shots has been recorded. When using the interval timer, select a release mode other than self-timer or high-speed frame capture. Option Description Start interval timer shooting.
Page 484
Option Description [ON]: Enable interval priority to ensure that frames shot in modes P and A are taken at the chosen interval. Flash photography is disabled. Release priority is enabled regardless of the options selected for Custom Settings a1 [AF-C priority selection] and a2 [AF-S priority selection].
Interval-Timer Photography Before Shooting Take a test shot at current settings. Before proceeding, select [Time zone and date] in the setup menu and make sure that the camera clock is set to the correct time and date. We recommend using one of the following power sources to prevent loss of power while shooting is in progress: A fully-charged battery An optional EH‑7P charging AC adapter...
Page 486
Choose the interval between shots. Highlight [Interval] and press Choose an interval (in hours, minutes, and seconds) and press J. Choose the number of intervals and number of shots per interval. Highlight [Intervals×shots/ Choose the number of interval] and press 2. intervals and the number of shots per interval and press In single frame release mode, the photographs for each interval will be taken at the rate...
Page 487
Choose an interval priority option. Highlight [Interval priority] and press 2 to select [ON] or [OFF]. Choose whether the camera focuses between shots. Highlight [Focus before each shot] and press 2 to select [ON] or [OFF]. If [ON] is selected for [Focus before each shot], the camera will focus before each shot according to the option currently selected for focus mode.
Page 488
Choose starting folder options. Highlight [Starting storage After highlighting the desired folder] and press 2. options and pressing J to turn them on (M) or off (U), press 4. Highlight [Start] and press J. If [Now] was selected for [Choose start day/time] in Step 2, shooting will start after about 3 s.
Page 489
Pausing Interval-Timer Photography Interval-timer photography can be paused between intervals by pressing J or by selecting [Interval timer shooting] in the photo shooting menu, highlighting [Pause], and pressing J. Note that the menus may not be displayed when the G button is pressed if the time selected for [Interval] is very short.
Page 490
To resume shooting at a specified time: Highlight [Restart option] and press 2, then highlight [Choose day/time] and press 2. Choose a starting date and time and press J. Highlight [Restart] and press J. Ending Interval-Timer Photography To end interval-timer photography before all the photos are taken, select [Interval timer shooting] in the photo shooting menu, highlight [Off], and press J.
Page 491
Cautions: Interval-Timer Photography Choose an interval longer than the time needed to take the selected number of shots at the predicted shutter speed. Note that during actual interval-timer photography, the camera must not only take shots at the selected interval but must also have sufficient time to complete the exposures and perform such tasks as processing the photographs.
Page 492
Release Mode Regardless of the release mode selected, the camera will take the specified number of shots at each interval. Adjusting Settings Between Shots Pictures can be viewed and shooting and menu settings adjusted between shots. Note, however, that the display will turn off and shooting will resume a few seconds before the next shot is taken. Interval-Timer Photography: Restrictions Interval-timer photography cannot be combined with some camera features, including: video recording,...
Time-Lapse Video G button U C photo shooting menu The camera automatically takes photos at selected intervals to create a time-lapse video. Option Description Start time-lapse recording. Shooting starts after about 3 s and continues at [Start] the interval selected for [Interval] for the time selected for [Shooting time]. [Interval] Choose the interval between shots, in minutes and seconds.
Page 494
Option Description [Focus before If [ON] is selected, the camera will focus between shots. each shot] Choose the slot used to record time-lapse videos when two memory cards [Destination] are inserted. Time-Lapse Video...
Recording Time-Lapse Videos Before Shooting Time-lapse videos are shot using the video crop. Take test shots and check the results in the monitor. Before proceeding, select [Time zone and date] in the setup menu and make sure that the camera clock is set to the correct time and date.
Page 496
Choose the total shooting time. Highlight [Shooting time] Choose a shooting time (in and press 2. hours and minutes) and press The maximum shooting time is 23 hours and 59 minutes. Enable or disable exposure smoothing. Highlight [Exposure smoothing] and press 2 to select [ON] or [OFF]. Selecting [ON] smooths abrupt changes in exposure.
Page 497
Choose a video file type. Highlight [Video file type] Highlight an option and press and press 2. Choose the frame size and rate. Highlight [Frame size/frame Highlight an option and press rate] and press 2. Choose an interval priority option. Highlight [Interval priority] and press 2 to select [ON] or [OFF].
Page 498
Choose whether the camera focuses between shots. Highlight [Focus before each shot] and press 2 to select [ON] or [OFF]. If [ON] is selected for [Focus before each shot], the camera will focus before each shot according to the option currently selected for focus mode. Choose a destination.
Page 499
During Shooting A 8 icon is displayed in the control panel during shooting. If the display is turned on by pressing the shutter-release button halfway, the message [Interval timer shooting] will be displayed and the 8 icon will flash. Time-Lapse Video...
Page 500
Ending Shooting To end shooting before all the photos are taken, press J or select [Time-lapse video] in the photo shooting menu, highlight [Off], and press J. Note that the menus may not be displayed when the G button is pressed if the time selected for [Interval] is very short. A video will be created from the frames shot to the point where shooting ended and normal photography will resume.
Page 501
Cautions: Time-Lapse Videos Sound is not recorded with time-lapse videos. The shutter speed and the time needed to record the picture to the memory card may vary from shot to shot. As a result, camera may be unable to take shots at the selected interval. Shooting will not begin if a time-lapse video cannot be recorded at current settings, for example if: the value selected for [Interval] is longer than that selected for [Shooting time], [00:00'00"] is selected for [Interval] or [Shooting time], or...
Focus Shift Shooting G button U C photo shooting menu Focus shift automatically varies focus over a series of shots. Use it to take photos that will later be combined using focus stacking to create a single picture with increased depth of field. Before using focus shift, choose a focus mode of AF‑S or AF‑C and a release mode other than self-timer or high-speed frame capture.
Focus Shift Photography Before Shooting Take a test shot at current settings. We recommend using one of the following power sources to prevent loss of power while shooting is in progress: A fully-charged battery An optional EH‑7P charging AC adapter An optional EH‑8P AC adapter with a UC‑E25 USB cable (featuring Type C connectors at both ends) An optional EP‑5B power connector with an EH‑5d, EH‑5c, or EH‑5b AC adapter...
Page 504
Adjust focus shift settings. Choose the number of shots. Highlight [No. of shots] and Choose the number of shots press 2. and press J. The maximum number of shots is 300. We recommend taking more shots than you think you’ll need. You can winnow them down during focus stacking.
Page 505
Choose the interval until next shot. Highlight [Interval until next Choose the interval between shot] and press 2. shots and press J. Choose the interval between shots, in seconds. Select [00] to take photos at up to about 5 fps. To ensure correct exposure when using a flash, choose an interval long enough for the flash to charge.
Page 506
Choose whether the focus position returns to the starting position at the end of each sequence. Highlight [Focus position auto reset] and press 2 to select [ON] or [OFF] We recommend selecting [ON] when using focus shift to photograph subjects at the same focus distance multiple times in succession.
Page 507
Ending Focus Shift Photography To end shooting before all shots have been taken, either: select [Focus shift shooting] in the photo shooting menu, highlight [Off], and press J, or press the shutter-release button halfway or press the J button between shots. During Shooting A 9 icon is displayed in the control panel during shooting.
Page 508
Tip: Aperture Given that pictures shot at very small apertures (high f-numbers) may lack definition, we recommend that you choose apertures wider (f-numbers lower) than f/8–f/11. Tip: Close-ups Because focus depth is reduced at short focus distances, we recommend choosing smaller focus steps and increasing the number of shots when photographing subjects close to the camera.
The Video Recording Menu Menu Items and Defaults To view the video recording menu, select the 1 tab in the camera menus. The options in the video recording menu are listed below, together with their default settings. [Shooting menu bank]: A [Extended menu banks]: OFF [Storage folder] [Rename]: NCZ_8...
Page 510
[Active D-Lighting]: Off [High ISO NR]: Normal [Vignette control]: Normal [Diffraction compensation]: ON [Auto distortion control]: ON [Skin softening]: Same as photo settings [Portrait impression balance]: Off [Video flicker reduction]: Auto [High-frequency flicker reduction]: Off [Metering]: Matrix metering [Focus mode]: Full-time AF [AF-area mode]: Single-point AF [AF subject detection options] [Subject detection]: Auto...
Shooting Menu Bank G button U 1 video recording menu Select a shooting menu bank (“A” through “D”). More information is available in the section devoted to the [Shooting menu bank] item in the photo shooting menu ( 421). Shooting Menu Bank...
Extended Menu Banks G button U 1 video recording menu Select [ON] to include exposure settings in the information recorded in each of the four shooting menu banks. More information is available in the section devoted to the [Extended menu banks] item in the photo shooting menu ( 423).
Storage Folder G button U 1 video recording menu Choose the folder in which subsequent pictures will be stored. More information is available in the section devoted to the [Storage folder] item in the photo shooting menu ( 424). “Storage Folder” Changes to [Storage folder] in the photo shooting menu apply in the video recording menu and vice versa.
File Naming G button U 1 video recording menu Choose the three-letter prefix used in naming the files in which videos are stored; the default prefix is “DSC” ( 427). File Naming...
Destination G button U 1 video recording menu Choose the slot to which videos are recorded when two memory cards are inserted. The menu shows the time available on each card. Recording ends automatically when no time remains on the current card. Destination...
Video File Type G button U 1 video recording menu Choose the video file type. For more information, see the section on “Video File Types” ( 190) in the “Video Recording” chapter. Video File Type...
Frame Size/Frame Rate G button U 1 video recording menu Choose the video frame size (in pixels) and frame rate. For more information, see the section on “Video Frame Size and Rate Options” ( 193) in the “Video Recording” chapter. Frame Size/Frame Rate...
Video Quality (N-RAW) G button U 1 video recording menu The quality for videos recorded with [N‑RAW 12-bit (NEV)] selected for [Video file type] in the video recording menu can be selected from [High quality] and [Normal]. Video Quality (N-RAW)
Image Area G button U 1 video recording menu Choose a video crop. For more information, see the section on “Video Image Area Options” ( 200) in the “Video Recording” chapter. Image Area...
Extended Oversampling G button U 1 video recording menu Selecting [ON] optimizes image readout for improved image quality. Extended oversampling applies when [3840×2160; 60p] or [3840×2160; 50p] is selected for [Frame size/frame rate] and [FX] is selected for [Image area] > [Choose image area] in the video recording menu.
ISO Sensitivity Settings G button U 1 video recording menu Adjust the following ISO sensitivity settings for use in video mode. Option Description Choose the upper limit for auto ISO sensitivity control from values between ISO 200 and Hi 2.0. [Maximum The selected value serves as the upper limit for ISO sensitivity in modes P, sensitivity] S, and A and when [ON] is selected for [Auto ISO control (mode M)] in mode M.
White Balance G button U 1 video recording menu Choose the white balance for videos. Select [Same as photo settings] to use the option currently selected for photos ( 143). White Balance...
Set Picture Control G button U 1 video recording menu Choose a Picture Control for videos. Select [Same as photo settings] to use the option currently selected for photos ( 175). Set Picture Control...
HLG Quality G button U 1 video recording menu Adjust HLG video image processing options for use when [HLG] is chosen as the tone mode for [Video file type] > [H.265 10-bit (MOV)] in the video recording menu. Option Description Use [Quick sharp] to quickly adjust levels for balanced [Sharpening], [Quick sharp] [Mid-range sharpening], and [Clarity].
Active D‑Lighting G button U 1 video recording menu Preserve details in highlights and shadows, creating videos with natural contrast. Option Description [Extra high] [High] Choose the amount of Active D-Lighting performed from (in order from high to low) [Extra high], [High], [Normal], and [Low]. [Normal] [Low] [Off]...
High ISO NR G button U 1 video recording menu Reduce “noise” (randomly-spaced bright pixels) in videos recorded at high ISO sensitivities ( 450). High ISO NR...
Vignette Control G button U 1 video recording menu Reduce vignetting in videos ( 451). Vignette Control Changes to [Vignette control] in the photo shooting menu apply in the video recording menu and vice versa. Vignette Control...
Diffraction Compensation G button U 1 video recording menu Choose whether to reduce diffraction in videos ( 452). Diffraction Compensation Changes to [Diffraction compensation] in the photo shooting menu apply in the video recording menu and vice versa. Diffraction Compensation...
Auto Distortion Control G button U 1 video recording menu Choose whether to reduce barrel and pin-cushion distortion in videos ( 453). Auto Distortion Control Changes to [Auto distortion control] in the photo shooting menu apply in the video recording menu and vice versa. Auto Distortion Control...
Skin Softening G button U 1 video recording menu Adjust skin softening settings for video recording. Select [Same as photo settings] to use the option currently selected for photos ( 454). Restrictions on Skin Softening in Video Mode Skin softening will not be performed if: [N‑RAW 12-bit (NEV)] or [ProRes RAW HQ 12-bit (MOV)] is selected for [Video file type] in the video recording menu, or [N-Log] is chosen for tone mode when [ProRes 422 HQ 10-bit (MOV)] or [H.265 10-bit (MOV)] is...
Portrait Impression Balance G button U 1 video recording menu Adjust portrait impression balance settings for video recording ( 455). Portrait Impression Balance...
Video Flicker Reduction G button U 1 video recording menu Reduce flicker and banding in the shooting display and in footage recorded under fluorescent or mercury-vapor lighting. Choose [Auto] to allow the camera to automatically choose the correct frequency. If [Auto] fails to produce the desired results, select [50 Hz] or [60 Hz] according to the frequency of the local power supply.
High-Frequency Flicker Reduction G button U 1 video recording menu Selecting [On (shutter speed fine-tuning)] allows shutter speeds between ¹⁄₈₀₀₀ and ¹⁄₃₀ s to be adjusted in smaller increments in mode M, letting speeds that keep flicker to a minimum be found by viewing the preview in the shooting display. More information is available in the section devoted to the [High-frequency flicker reduction] item in the photo shooting menu ( 459).
Metering G button U 1 video recording menu Choose how the camera meters exposure in video mode. [Spot metering] is not available in the video recording menu ( 461). Metering...
AF Subject Detection Options G button U 1 video recording menu Subject Detection Choose the type of subject to which the camera gives priority when focusing in video mode ( 111). AF When Subject Not Detected Choose whether the camera focuses if unable to detect a subject of the type selected for [Subject detection] when [Full-time AF] is selected for focus mode.
Vibration Reduction G button U 1 video recording menu Adjust vibration reduction settings for video mode. Select [Same as photo settings] to use the option currently selected for photos ( 470). Vibration Reduction...
Electronic VR G button U 1 video recording menu Choose whether to enable electronic vibration reduction in video mode. Caution: Electronic Vibration Reduction [Electronic VR] is fixed at [OFF] while: [N‑RAW 12-bit (NEV)] or [ProRes RAW HQ 12-bit (MOV)] is selected for [Video file type] in the video recording menu, 7680 ×...
Microphone Sensitivity G button U 1 video recording menu Turn built-in or external microphones on or off or adjust microphone sensitivity. Option Description [Auto] Microphone sensitivity is adjusted automatically. Adjust microphone sensitivity manually. Choose from values of from [1] to [20]. The higher the value, the higher the sensitivity;...
Attenuator G button U 1 video recording menu Select [ON] to reduce microphone gain and prevent audio distortion when recording videos in loud environments. Attenuator...
Frequency Response G button U 1 video recording menu Choose the range of frequencies to which built-in and external microphones respond. Option Description Record a wide range of frequencies. Choose for everything from music to [Wide range] the bustling hum of a city street. [Vocal range] Choose for human voices.
Wind Noise Reduction G button U 1 video recording menu Select [ON] to enable the low-cut filter, reducing noise produced by wind blowing over the built-in microphone. Note that other sounds may also be affected. Selecting [ON] for [Wind noise reduction] has no effect on optional stereo microphones. Wind-noise reduction for optional stereo microphones that support this feature can be enabled or disabled using microphone controls.
Mic Jack Plug-in Power G button U 1 video recording menu The camera does not provide power to external microphones when [OFF] is selected. To prevent noise from interference generated by the power supply, we recommend turning plug-in power [OFF] when using microphones that do not require plug-in power. For information on whether your microphone requires plug-in power, consult the manufacturer.
Timecode G button U 1 video recording menu Choose whether to record time codes giving the hour, minute, second, and frame number for each frame when shooting videos. Time codes are not included in videos shot with [H.264 8-bit (MP4)] selected for [Video file type] in the video recording menu. Option Description [On]: Record time codes.
“Reset Using Remote” This option allows the time code to be reset by pressing the shutter-release button on an optional WR‑T10 paired with an optional WR‑R11a or WR‑R10 wireless remote controller attached to the camera. Selecting [Reset using remote] displays a time-code reset dialog. Press the shutter-release button on the WR-T10 to reset the time code.
External Rec. Cntrl (HDMI) G button U 1 video recording menu Selecting [ON] allows camera controls to be used to start and stop recording on the external recorder. For more information, see the section on “Recorders” ( 292) in the “Connecting to HDMI TVs and Recorders”...
Hi-Res Zoom G button U 1 video recording menu Selecting [ON] allows you to zoom in on your subject with no loss in resolution without using a zoom lens. For more information, see the section on “Hi-Res Zoom” ( 209) in the “Video Recording” chapter.
The Custom Settings Menu Menu Items and Defaults To view Custom Settings, select the A tab in the camera menus. Custom Settings are used to customize camera settings to suit individual preferences. The Custom Settings menu is divided into two levels. Menu Items and Defaults...
Page 552
1 The options in the Custom Settings menu are listed below, together with their default settings. [Custom Settings bank]: A a [Focus] a1: [AF-C priority selection]: Release a2: [AF-S priority selection]: Focus a3: [Focus tracking with lock-on] [Blocked shot AF response]: 3 [Subject motion]: Steady a4: [Focus points used]: All points a5: [Store points by orientation]: Off...
Page 553
b4: [Matrix metering face detection]: ON b5: [Center-weighted area]: Standard b6: [Fine-tune optimal exposure] [Matrix metering]: 0 [Center-weighted metering]: 0 [Spot metering]: 0 [Highlight-weighted metering]: 0 b7: [Keep exp. when f/ changes]: Exposure maintenance off c [Timers/AE lock] c1: [Shutter-release button AE-L]: Off c2: [Self-timer] [Self-timer delay]: 10 s [Number of shots]: 1...
Page 554
d12: [View all in continuous mode]: ON d13: [Release timing indicator] [Indicator type]: Type B [Type A auto restore delay]: 1/6 s d14: [Image frame]: ON d15: [Grid type]: 3×3 d16: [Virtual horizon type]: Type A d17: [Custom monitor shooting display] [Display 1]: L (cannot be deselected) [Display 2]: M [Display 3]: M...
Page 555
[Video record button]: Live view info display off [Exposure compensation button]: Exposure compensation [ISO sensitivity button]: ISO sensitivity [Command dials] [Exposure setting] :P: 3--/yP*, S: 3--/yTv, A: 3Av/y--, M: 3Av/yTv [Focus/AF-area mode selection]: 3t/ys [Sub-command dial zoom role]: Exposure setting [Lens Fn button]: AE/AF lock [Lens Fn2 button]: AF-ON [Lens Fn ring (counterclockwise)]: Recall focus position...
Page 556
[Flick advance direction]: LeftVRight f13: [Prefer sub-selector center]: ON g [Video] g1: [Customize i menu]: Set Picture Control, White balance, Frame size/frame rate, Microphone sensitivity, AF-area mode/subj. detection, Focus mode, Electronic VR, Vibration reduction, Shooting menu bank, Custom controls, Airplane mode, Destination g2: [Custom Controls] [Fn1 button]: Shooting menu bank [Fn2 button]: Choose image area...
Page 557
[Auto-area AF]: M g5: [Focus mode restrictions]: No restrictions g6: [AF speed]: 0 [When to apply]: Always g7: [AF tracking sensitivity]: 4 g8: [Hi-Res Zoom speed]: Standard g9: [Fine ISO control (mode M)]: Off g10: [Extended shutter speeds (mode M)]: OFF g11: [View assist]: OFF g12: [Zebra pattern] [Pattern tone range]: Zebra pattern off...
Custom Settings Bank G button U A Custom Settings menu Custom Settings are stored in one of four banks (banks “A” through “D”) that can be selected using [Custom Settings bank]. Changes to settings made while one bank is selected are not applied to the remaining banks.
a1: AF-C Priority Selection G button U A Custom Settings menu Choose whether photos can be taken before the camera focuses when AF-C is selected. Option Description Photos can be taken whenever the shutter-release button is pressed (release [Release] priority). Priority is normally given to release, but if the subject is dark or low contrast and the camera is in continuous-release mode, priority will be given to focus [Focus + for the first shot in each series.
a2: AF-S Priority Selection G button U A Custom Settings menu Choose whether photos can be taken before the camera focuses when AF-S is selected. Option Description Photos can be taken whenever the shutter-release button is pressed (release [Release] priority). [Focus] Photos can be taken only when the camera is in focus (focus priority). a2: AF-S Priority Selection...
a3: Focus Tracking with Lock-On G button U A Custom Settings menu Choose how quickly focus responds if something passes between the subject and the camera when AF‑C is selected for the focus mode. Blocked Shot AF Response Choose [5] ([Delayed]) to help maintain focus on your original subject. Choose [1] ([Quick]) to make it easier to shift focus to objects crossing your field of view.
a4: Focus Points Used G button U A Custom Settings menu Choose the number of focus points available for manual focus-point selection when an option other than [Auto-area AF] is selected for AF-area mode. Option Description Every focus point available in the current AF-area mode can be selected. [All points] The number of points available varies with the AF-area mode.
a5: Store Points by Orientation G button U A Custom Settings menu Choose whether separate focus points can be selected for “wide” (landscape) orientation, for “tall” (portrait) orientation with the camera rotated 90° clockwise, and for “tall” orientation with the camera rotated 90° counterclockwise. Select [Off] to use the same focus point regardless of camera orientation.
Page 564
Select [Focus point] to enable separate focus-point selection. To enable separate selection of both the focus point and AF-area mode, choose [Focus point and AF-area mode]. Camera rotated 90° counter- Landscape (wide) orientation Camera rotated 90° clockwise clockwise a5: Store Points by Orientation...
a6: AF Activation G button U A Custom Settings menu Choose whether the shutter-release button can be used to focus. Option Description [Shutter/AF-ON] The camera focuses when the shutter-release button is pressed halfway. [AF-ON only] The camera does not focus when the shutter-release button is pressed halfway. Highlighting [AF-ON only] and pressing 2 displays [Out-of-focus release] options.
a7: Focus Point Persistence G button U A Custom Settings menu Choose whether the focus point selected by the camera continues in use after you change AF-area modes using a control to which [AF-area mode], [AF-area mode + AF-ON], [Recall shooting functions], or [Recall shooting functions (hold)] has been assigned via Custom Setting f2 [Custom controls (shooting)].
a8: Limit AF-Area Mode Selection G button U A Custom Settings menu Choose the AF-area modes that can be selected by pressing the focus-mode button and rotating the sub-command dial. Highlight options and press J or 2 to select (M) or deselect (U). Modes marked with a check (M) are available for selection via the sub-command dial.
a9: Focus Mode Restrictions G button U A Custom Settings menu Limit focus-mode selection to a single focus mode. If an option other than [No restrictions] is selected, rotating the main command dial while holding the focus-mode button will not change the focus mode. a9: Focus Mode Restrictions...
a10: Focus Point Wrap-Around G button U A Custom Settings menu Choose whether focus-point selection “wraps around” from one edge of the display to another. If [ON] is selected, focus-point selection will “wrap around” from top to bottom, bottom to top, right to left, and left to right, so that, for example, pressing 2 when a focus point at the right edge of the display is highlighted selects the corresponding point at the left edge.
a11: Focus Point Display G button U A Custom Settings menu Choose from the focus point display options below. Manual Focus Mode Option Description [ON] The focus point is displayed at all times in manual focus mode. [OFF] The focus point is displayed only during focus-point selection. Dynamic-Area AF Assist Choose whether both the selected focus point and the surrounding focus points are displayed in dynamic-area AF mode.
AF-C In-Focus Display Choose whether the focus point changes color when the subject is in focus in focus mode AF‑C. Option Description [ON] The focus point is displayed in green when the camera judges that the subject is in focus. The active focus point is displayed in red or yellow at all times, whether or not the camera [OFF] is in focus.
Do not obstruct the AF-assist illuminator while it is lit. Some lenses may block the light from the AF-assist illuminator at some or all focus distances. Information on these restrictions is available from the Nikon Download Center. https://downloadcenter.nikonimglib.com/ a12: Built-in AF-Assist Illuminator...
a13: Focus Peaking G button U A Custom Settings menu When focus peaking is enabled in manual focus mode, objects that are in focus are indicated by colored outlines in the display. You can choose the color. Focus Peaking Display Select [ON] to enable focus peaking. Focus Peaking Sensitivity Choose focus peaking sensitivity from [3 (high sensitivity)], [2 (standard)], and [1 (low sensitivity)].
a14: Focus Point Selection Speed G button U A Custom Settings menu The speed at which the camera cycles through focus points while the multi selector or sub-selector is pressed can be chosen from [Low], [Normal], and [High]. a14: Focus Point Selection Speed...
a15: Manual Focus Ring in AF Mode G button U A Custom Settings menu This item is available with compatible lenses only. Use it to choose whether the lens focus ring can be used for manual focus in autofocus mode. Option Description Autofocus can be over-ridden by rotating the lens focus ring (autofocus with manual override).
b1: ISO Sensitivity Step Value G button U A Custom Settings menu Choose whether changes to ISO sensitivity are made in increments of ¹⁄₃ or 1 EV. If the value currently selected for ISO sensitivity is not available at the chosen setting, ISO sensitivity will be set to the nearest available value.
b2: EV Steps for Exposure Cntrl G button U A Custom Settings menu Select the increments used for adjustments to shutter speed, aperture, bracketing, and exposure and flash compensation. If [1 EV steps (comp. 1/3 EV)] is selected, changes to shutter speed, aperture, and bracketing will be made in increments of 1 EV and changes to exposure and flash compensation in increments of ¹⁄₃ EV.
b3: Easy Exposure Compensation G button U A Custom Settings menu Choose whether the E button is needed for exposure compensation. Option Description Exposure compensation can be adjusted using only a command dial. The [On (Auto reset)] setting selected with the command dial is reset when the camera turns off or the standby timer expires.
b4: Matrix Metering Face Detection G button U A Custom Settings menu Choose whether exposure is adjusted for the faces of human portrait subjects detected by the camera when [Matrix metering] is selected. Option Description [ON] The camera adjusts exposure for faces. [OFF] Exposure is not adjusted according to whether faces have been detected.
b5: Center-Weighted Area G button U A Custom Settings menu When [Center-weighted metering] is selected, the camera assigns the greatest weight to an area in the center of the shooting display when setting exposure. Option Description The camera assigns the greatest weight to an area equivalent to a circle [Small] 8 mm in diameter.
b6: Fine-Tune Optimal Exposure G button U A Custom Settings menu Use this option to fine-tune the exposure value selected by the camera; exposure can be fine-tuned separately for each metering method. Exposure can be adjusted up for brighter exposures or down for darker exposures in the range +1 to –1 EV in steps of ¹⁄₆ EV.
b7: Keep Exp. When f/ Changes G button U A Custom Settings menu When [OFF] is selected for [ISO sensitivity settings] > [Auto ISO sensitivity control] in the photo shooting menu in mode M, actions such as switching to a lens with a different aperture range may cause unintended changes to aperture.
c1: Shutter-Release Button AE-L G button U A Custom Settings menu Choose whether exposure locks when the shutter-release button is pressed. Option Description [On (half press)] Pressing the shutter-release button halfway locks exposure. Exposure only locks while the shutter-release button is pressed all the [On (burst mode)] way down.
c2: Self-Timer G button U A Custom Settings menu Choose the length of the shutter release delay, the number of shots taken, and the interval between shots in self-timer mode. Option Description [Self-timer delay] Choose the length of the shutter-release delay. Press 1 and 3 to choose the number of shots taken each time the [Number of shots] shutter-release button is pressed;...
c3: Power Off Delay G button U A Custom Settings menu Choose how long the displays remain on, and how long the camera waits before returning from picture review to shooting mode, when no operations are performed. Longer power-off delays reduce battery endurance. Option Description Choose how long the monitor or viewfinder waits to turn off after playback...
d1: Continuous Shooting Speed G button U A Custom Settings menu Choose the frame advance rate for continuous high-speed and continuous low-speed modes. Option Description Choose the frame rate for continuous high-speed release mode from [Continuous high-speed] options ranging from 10 to 20 fps. Choose the frame rate for continuous low-speed release mode from [Continuous low-speed] options ranging from 1 to 10 fps.
d2: Maximum Shots per Burst G button U A Custom Settings menu The maximum number of shots that can be taken in a single burst in continuous release modes can be set to “∞” (no limit) or to any value between 1 and 200. Note that regardless of the option selected, there is no limit to the number of photos that can be taken in a single burst when a shutter speed of 1 s or slower is selected in mode S or M.
d3: Pre-Release Capture Options G button U A Custom Settings menu Choose the length of the burst recorded from the end of the memory buffer when the shutter-release button is pressed all the way down and the maximum length of the burst recorded while the shutter- release is fully pressed in high-speed frame capture mode.
Page 589
Option Description If an option other than [None] is selected, the camera will buffer frames while the shutter-release button is pressed halfway, but only the frames added to the buffer in the final n seconds, where n is the value selected for [Pre-release burst], will be recorded to the memory card when the [Pre-release burst] shutter-release button is pressed all the way down (“Pre-Release Capture”).
d4: Sync. Release Mode Options G button U A Custom Settings menu Choose whether the shutters on the remote cameras are synchronized with the shutter on the master camera when using an optional wireless remote controller or the [Connect to other cameras] item in the network menu.
d5: Extended Shutter Speeds (M) G button U A Custom Settings menu Extend the range of shutter speeds available in mode M; the slowest shutter speed available when [ON] is selected is 900 s (15 minutes). Extended shutter speeds can be used for pictures of the night sky and other long exposures.
d6: Limit Selectable Image Area G button U A Custom Settings menu Choose the options that can be accessed by rotating a command dial in the i menu or while pressing a control to which image area has been assigned. Highlight options and press J or 2 to select (M) or deselect (U). Modes marked with a check (M) are available for selection via the command dials.
d7: File Number Sequence G button U A Custom Settings menu Choose a file numbering option. Option Description When a new folder is created or a new memory card is inserted in the camera, file [On] numbering will continue from the last number used. This simplifies file management by minimizing the occurrence of duplicate file names when multiple cards are used.
Page 594
File Number Sequence If a picture is taken when the current folder contains a picture numbered 9999, a new folder will be created and file numbering will restart from 0001. When the current folder number reaches 999, the camera will no longer be able to create new folders and the shutter release will be disabled if: the current folder contains 5000 pictures (in addition, video recording will be disabled if the camera calculates that the number of files needed to record a video of the maximum length...
d8: View Mode (Photo Lv) G button U A Custom Settings menu Choose whether the camera adjusts the preview in the viewfinder or monitor to reflect how shooting settings will affect the hue and brightness of the final picture. Regardless of the option selected, the effects of camera settings are always visible in video mode.
Page 596
Option Description The effects of changes to settings such as white balance, Picture Controls, and exposure compensation are not visible in the shooting display. Pressing 2 when [Adjust for ease of viewing] is highlighted displays [Auto] and [Custom] options. [Auto]: Color, brightness, and other settings are adjusted for ease of viewing during prolonged periods of use.
d9: Starlight View (Photo Lv) G button U A Custom Settings menu Select [ON] to brighten the display for ease of viewing in dark environments (starlight view). Note that the display may become slightly jerky when starlight view is in effect. d9: Starlight View (Photo Lv)
d10: Warm Display Colors G button U A Custom Settings menu Use warmer colors with reduced brightness in the shooting, menu, and/or playback displays. This makes the displays easier to view with vision adapted to dark environments during astronomical photography and the like. Option Description Choose from the following options.
d11: LCD Illumination G button U A Custom Settings menu Choose when the control panel and button backlights light. If [OFF] is selected, the backlights will light when the power switch is rotated to D. The backlights turn off when the shutter-release button is pressed. If [ON] is selected, the backlights will light while the standby timer is active.
d12: View All in Continuous Mode G button U A Custom Settings menu If [OFF] is selected, the display will go blank during burst photography. d12: View All in Continuous Mode...
d13: Release Timing Indicator G button U A Custom Settings menu Adjust settings related to how the display responds when the shutter is released. Option Description Choose how the display responds when the shutter is released. [Type A]: The display goes dark when the shutter is released. This makes it easier to track the subject during panning shots.
d14: Image Frame G button U A Custom Settings menu Select [OFF] to hide the white border around the shooting displays in the monitor and viewfinder. d14: Image Frame...
d15: Grid Type G button U A Custom Settings menu Choose a framing grid for the shooting display. The selected grid can be displayed by placing a check (M) next to b in the list for Custom Setting d17 [Custom monitor shooting display] ( 607) or d18 [Custom viewfinder shooting display] ( 609).
d16: Virtual Horizon Type G button U A Custom Settings menu Choose a virtual horizon for the shooting display. The selected virtual horizon can be displayed by placing a check (M) next to D in the list for Custom Setting d17 [Custom monitor shooting display] 607) or d18 [Custom viewfinder shooting display] ( 609).
Pitch Camera tilted forward Camera tilted back Option [Type A] [Type B] The Virtual Horizon Display Note that the display may not be accurate when the camera is tilted at a sharp angle forward or back. The camera will not display the virtual horizon or pitch and roll indicators when held at angles at which tilt cannot be measured.
d17: Custom Monitor Shooting Display G button U A Custom Settings menu Choose the monitor displays accessible by pressing the DISP button during shooting. Highlight items ([Display 2] through [Display 5]) and press J to select (M) or deselect (U). Only displays marked with a check (M) can be accessed by pressing the DISP button during shooting.
Page 608
Option Description Add an 8 or 12 mm circle to the center of the shooting display whenever [Center-weighted metering] is selected for [Metering] in the photo shooting menu. [Center-weighted area] The size of the circle varies with the option selected for Custom Setting b5 [Center-weighted area].
d18: Custom Viewfinder Shooting Display G button U A Custom Settings menu Choose the viewfinder displays accessible by pressing the DISP button during shooting. Highlight items ([Display 2] through [Display 4]) and press J to select (M) or deselect (U). Only displays marked with a check (M) can be accessed by pressing the DISP button during shooting. [Display 1] cannot be deselected.
d19: High FPS Viewfinder Display G button U A Custom Settings menu Select [ON] to smooth the display in the viewfinder according to shooting conditions. The movements of fast-moving subjects will be easier to see. d19: High FPS Viewfinder Display...
e1: Flash Sync Speed G button U A Custom Settings menu Choose the flash sync speed. Option Description [1/250 s (Auto FP)] Flash sync speed is set to ¹⁄₂₅₀ or ¹⁄₂₀₀ s. With compatible flash units, auto FP high-speed sync will automatically be enabled at shutter speeds faster than ¹⁄₂₅₀...
Page 612
Caution: Auto FP High-Speed Sync Depending on the shutter speed, horizontal lines may appear in pictures taken using auto FP high- speed sync when [1/250 s (Auto FP)] or [1/200 s (Auto FP)] is selected. This effect can be mitigated choosing a slower shutter speed or adjusting flash output.
e2: Flash Shutter Speed G button U A Custom Settings menu Choose the slowest shutter speed available with a flash in mode P or A. Regardless of the setting chosen for Custom Setting e2 [Flash shutter speed], shutter speeds can be as slow as 30 s in modes S and M or at flash settings of slow sync, slow rear-curtain sync, or red-eye reduction with slow sync.
e3: Exposure Comp. for Flash G button UA Custom Settings menu Choose how the camera adjusts flash level when exposure compensation is used. Option Description The camera adjusts both the flash level and exposure. This changes [Entire frame] the exposure for the entire frame. [Background only] Exposure compensation is adjusted for the background only.
e4: Auto c ISO Sensitivity Control G button U A Custom Settings menu Choose how the camera adjusts flash level when auto ISO sensitivity control is enabled. Option Description [Subject and The camera takes both the main subject and background lighting background] into account when adjusting ISO sensitivity. ISO sensitivity is adjusted only to ensure that the main subject is [Subject only] correctly exposed.
Modeling Flash G button U A Custom Settings menu If [ON] is selected when the camera is used with an optional flash unit that supports the Nikon Creative Lighting system, pressing a control to which [Preview] has been assigned using Custom Setting f2 [Custom controls (shooting)] will emit a modeling flash.
e6: Auto Bracketing (Mode M) G button U A Custom Settings menu The settings affected when bracketing is enabled in mode M and [OFF] is selected for [ISO sensitivity settings] > [Auto ISO sensitivity control] in the photo shooting menu are determined by the options selected for [Auto bracketing] >...
e7: Bracketing Order G button U A Custom Settings menu Choose the order in which the shots in the bracketing program are taken. Option Description The unmodified shot is taken first, followed by the shot with the [MTR > under > over] lowest value, followed by the shot with the highest value. [Under >...
e8: Flash Burst Priority G button U A Custom Settings menu Choose whether optional flash units emit monitor pre-flashes before each shot during burst photography in high- or low-speed continuous release mode. Option Description The flash unit emits a monitor pre-flash before the first shot in each sequence and locks output at the metered value for the remaining shots.
f1: Customize i Menu G button U A Custom Settings menu Choose the items listed in the i menu displayed when the i button is pressed in photo mode. Highlight a position in the i menu, press J, and select the desired item. The following items can be assigned to the i menu.
Option [Pre-Release Capture options] [Release mode] [Custom controls (shooting)] [View mode (photo Lv)] [Split-screen display zoom] [Focus peaking] [Monitor/viewfinder brightness] 714, [Airplane mode] [Warm display colors] [MB-N12 info] View Memory Card Info View the slot currently selected as the destination for new pictures and the options used to record pictures when two memory cards are inserted.
Split-Screen Display Zoom If [Split-screen display zoom] is assigned to the i menu, you can select [Split-screen display zoom] to simultaneously zoom in on two areas that are aligned horizontally but are in different parts of the frame (split-screen display zoom). The locations of the areas are indicated by the two frames (r) in the navigation window in the bottom right corner of the display.
f2: Custom Controls (Shooting) G button U A Custom Settings menu Choose the operations performed in photo mode using lens rings and camera buttons and command dials. You can also choose the roles played by the controls on optional battery packs connected to the camera.
Page 625
Option [ISO sensitivity button] [Command dials] [Lens Fn button] [Lens Fn2 button] [Lens Fn ring (counterclockwise)] [Lens Fn ring (clockwise)] [Lens memory set button] [Lens control ring] The roles that can be assigned are listed below. The roles available vary with the control. Role Description Pressing the control selects a preset focus point.
Page 626
Role Description Holding the control saves the current focus position. The saved position can be restored using a control to which [Recall focus position] has been assigned (“memory recall”). [Save focus When saving the focus position, you can choose whether it position] can be recalled using any of the controls to which [Recall focus position] is assigned ([Save to all]) or using only a...
Page 627
Role Description If [Auto] or [Natural light auto] is selected for white balance, white balance will lock when the control is pressed (white- [AWB lock (hold)] balance lock). White-balance lock does not end when the shutter is released. The lock will however be released when the control is pressed a second time or the standby timer expires.
Page 628
Role Description Hold the control to recall previously-selected settings. To choose the settings recalled, press 2 when [Recall shooting functions] is highlighted. Highlight items using 1 or 3 and press J to select (M) or deselect (U). Only items marked with a check (M) will be recalled while the button is pressed.
Page 629
Role Description Pressing the control allows shutter speed to be fine-tuned in [High-frequency smaller increments. Press the control a second time to restore flicker reduction] normal shutter-speed selection. If the control is pressed when an option other than [WB bracketing] is selected for [Auto bracketing] > [Auto bracketing set] in the photo shooting menu in continuous release mode, the camera will take all the shots in the current bracketing program and repeat the bracketing burst...
Page 630
Role Description Press the control to remotely take over the master camera role from another camera functioning as a master camera commanding remote cameras during synchronized release. [Override other This option takes effect when multiple cameras in the same cameras] group have been designated as masters using [Connect to other cameras] in the network menu.
Page 631
Role Description [Starlight view Press the control to toggle starlight view on. Press again to (photo Lv)] end starlight view. Press the control to switch the option selected for Custom [View mode (photo Setting d8 [View mode (photo Lv)] from [Show effects of Lv)] settings] to [Adjust for ease of viewing] or vice versa.
Page 632
Role Description To choose a white balance option, hold the control and rotate [White balance] the main command dial. Some options offer sub-options that can be selected by rotating the sub-command dial. Press the control and rotate a command dial to choose a [Set Picture Control] Picture Control.
Page 633
Role Description Press the control and rotate the main command dial to choose [Multiple exposure] the mode and the sub-command dial to choose the number of shots. Press the control and rotate the main command dial to choose [HDR overlay] the mode and the sub-command dial to adjust HDR strength.
Page 634
Role Description Adjust ISO sensitivity either by holding the control and [ISO sensitivity] rotating a command dial or by rotating the lens control ring. Rotate the lens Fn ring counterclockwise to widen the lens [Aperture (open)] aperture. This option is enabled automatically when [Aperture (close)] is selected for [Lens Fn ring (clockwise)].
Command Dials The following roles can be assigned to the command dials. To view options, highlight items and press Role Description Reverse the roles of the main and sub-command dials in selected modes. [Exposure setting] Press 4 or 2 to highlight a mode and 1 or 3 to switch roles. [Focus/AF-area Switch the roles played by rotating the main and sub-command dials while mode selection]...
Saving and Recalling Focus Positions You can save the current focus position by pressing and holding a custom control to which you have assigned [Save focus position]. The saved focus position can be instantly restored by pressing a custom control assigned [Recall focus position] (“memory recall”). You may find this useful if you frequently return to subjects at a fixed focus distance.
Page 637
“Save to All” Assign [Recall focus position] to a control. Repeat this step for each of the controls you intend to use for memory recall. Select another control in the custom control list and, when prompted to choose a role, highlight [Save focus position] and press 2.
Page 638
Press any of the controls to which [Recall focus position] was assigned in Step 1. The saved focus position will be restored. Although [Recall focus position] can be assigned to multiple controls, the same focus position will be restored regardless of the control used. Holding a control to which [Recall focus position] is assigned activates manual focus (MF), and the camera will not refocus if the shutter-release button is pressed halfway...
Page 639
“Save Individually” Assign [Recall focus position] to multiple controls. Select another control in the custom control list and, when prompted to choose a role, highlight [Save focus position] and press 2. Save options will be displayed. Highlight [Save individually] and press J. Focus on the desired subject in the shooting display and press and hold the control to which [Save focus position] is assigned.
Page 640
Press the button you intend to use for recall of the focus position saved in Step 4. Of the controls to which [Recall focus position] was assigned in Step 1, press the control you intend to use for recall of the focus position saved in Step 4. A message will appear in the shooting display if the operation is successful.
f3: Custom Controls (Playback) G button U A Custom Settings menu Choose the operations performed during playback using camera buttons and command dials. You can also choose the roles played by the controls on optional battery packs connected to the camera. Choose the roles played by the controls below. Highlight the desired control and press J.
Page 642
The roles that can be assigned to these controls are listed below. The roles available vary with the control. Role Description [Protect] Press the control to toggle protection for the current picture on or off. Press the control to zoom the display in on the area around the current focus point (the zoom ratio is selected in advance).
Page 643
Role Description [Thumbnail Press the control to toggle between full-frame and 4-, 9-, or 72-frame on/off] thumbnail playback. [View A histogram is displayed while the control is pressed. The histogram histograms] display is available in both full-frame and thumbnail playback. [Choose slot Press the control to display the [Choose slot and folder] dialog, and folder]...
Command Dials The following roles can be assigned to the command dials. To view options, highlight items and press Frame Advance Choose the number of frames that can be skipped by rotating the command dials during full-frame playback. Option Description [1 frame] Skip forward or back a frame at a time.
Page 645
Video Playback Choose the roles played by the command dials during video playback. Option Description [1 frame] Advance or rewind a frame at a time. [5 frames] Advance or rewind 5 frames at a time. [10 frames] Advance or rewind 10 frames at a time. [2 s] Skip forward or back 2 s at a time.
f4: Control Lock G button U A Custom Settings menu Lock exposure settings or focus-point selection. Option Description Select [ON] to lock shutter speed at its current value in modes S and M. [Shutter speed lock] O icons appear in the shooting display and control panel when shutter- speed lock is in effect.
f5: Reverse Dial Rotation G button U A Custom Settings menu Reverse the direction of rotation of the command dials for selected operations. Highlight [Exposure compensation] or [Shutter speed/aperture] and press 2 to select (M) or deselect (U). Press G to save changes and exit. The selected setting also applies to the command dials on optional battery packs.
f6: Release Button to Use Dial G button U A Custom Settings menu Selecting [ON] allows adjustments that are normally made by holding a button and rotating a command dial to be made by rotating the command dial after the button is released. This ends when the button is pressed again, the shutter-release button is pressed halfway, or the standby timer expires.
f7: Reverse Indicators G button U A Custom Settings menu Choose whether certain horizontal indicators in the shooting and other displays are shown with negative values on the left and positive values on the right, or with positive values on the left and negative values on the right.
f8: Reverse Ring for Focus G button U A Custom Settings menu Select [ON] to reverse the direction of rotation for the focus or control rings on Z mount lenses during manual focus. This option does not support: certain Z mount lenses that can only be focused manually, or F mount lenses connected via an FTZ II/FTZ mount adapter.
f9: Focus Ring Rotation Range G button U A Custom Settings menu Choose how far the focus or control rings on Z mount lenses must be rotated to go all the way from the minimum focus distance to infinity. Option Description The focus distance changes by a large amount when the ring is rotated rapidly and [Non-linear] by a small amount when the ring is rotated slowly, without regard to how far the ring is rotated.
f10: Control Ring Response G button U A Custom Settings menu Choose how responsive the lens control ring is when assigned the following roles using Custom Setting f2 [Custom controls (shooting)] or g2 [Custom controls]. Roles assigned using Custom Setting f2 [Custom controls (shooting)] or g2 [Custom controls]: [Aperture], [Power aperture], [Exposure compensation], [ISO sensitivity] Roles assigned using Custom Setting g2 [Custom controls]: [Hi-...
f11: Switch Focus/Control Ring Roles G button U A Custom Settings menu If [ON] is selected, the focus ring will perform the role currently assigned to the control ring using Custom Setting f2 [Custom controls (shooting)] or g2 [Custom controls]. When [ON] is selected, the control ring functions solely in the [Focus (M/A)] role. This option applies only to compatible lenses.
f12: Full-Frame Playback Flicks G button U A Custom Settings menu Choose the role assigned to the flick up and down or flick left and right gestures during full-frame playback. Flick Up/Flick Down Choose the operation performed by flicking up or down. Option Description Assign the current picture a pre-selected rating.
Flick Advance Direction Choose the gesture used for frame advance. Option Description [Left←Right] Flick from right to left to view the next picture. [Left→Right] Flick from left to right to view the next picture. f12: Full-Frame Playback Flicks...
f13: Prefer Sub-selector Center G button U A Custom Settings menu Choose how the sub-selector behaves while its center is pressed. Option Description [ON] The sub-selector cannot be used to position the focus point while the center is pressed. [OFF] The sub-selector can be used to position the focus point while the center is pressed. The center of the sub-selector, meanwhile, functions in the role chosen for [Sub-selector center] using Custom Setting f2 [Custom controls (shooting)] or g2 [Custom controls].
g1: Customize i Menu G button U A Custom Settings menu Choose the items listed in the i menu displayed when the i button is pressed in video mode. Highlight a position in the i menu, press J, and select the desired item. The following items can be assigned to the i menu.
Multi-Selector Power Aperture Choose whether the multi selector can be used for power aperture. When [Enable] is selected, holding 1 widens the aperture. Holding 3 narrows the aperture. Multi Selector Exposure Comp. Choose whether the multi selector can be used to adjust exposure compensation. Selecting [Enable] allows exposure compensation to be set by pressing 1 or 3.
g2: Custom Controls G button U A Custom Settings menu Choose the operations performed in video mode using lens rings and camera buttons and command dials. You can also choose the roles played by the controls on optional battery packs connected to the camera.
Page 661
Option [ISO sensitivity button] [Exposure compensation button] [Shutter-release button] [Command dials] [Lens Fn button] [Lens Fn2 button] [Lens Fn ring (counterclockwise)] [Lens Fn ring (clockwise)] [Lens memory set button] [Lens control ring] The roles that can be assigned are listed below. The roles available vary with the control. Role Description Pressing the control selects a preset focus point.
Page 662
Role Description Holding the control saves the current focus position. The saved position can be restored using a control to which [Recall focus position] has been assigned (“memory recall”). When saving the focus position, you can choose whether it [Save focus position] can be recalled using any of the controls to which [Recall focus position] is assigned ([Save to all]) or using only a specific control ([Save individually]).
Page 663
Role Description Exposure locks when the control is pressed. White balance will also lock provided [Auto] or [Natural light auto] is selected [AE/AWB lock for white balance. Exposure and white-balance lock do not (hold)] end when recording begins. The lock will however be released when the control is pressed a second time or the standby timer expires.
Page 664
Role Description Press the control to enable the virtual horizon display. Press [Virtual horizon] again to hide the display. The display type can be selected using Custom Setting d16 [Virtual horizon type]. [Focus peaking Press the control once to enable focus peaking when MF is display] selected for focus mode.
Page 665
Role Description Exposure compensation increases while the button is pressed. This option is enabled automatically when [Exposure compensation −] is selected for [Fn2 button]. [Exposure Rotate the lens Fn ring clockwise for increased exposure compensation +] compensation. This option is enabled automatically when [Exposure compensation −] is selected for [Lens Fn ring (counterclockwise)].
Page 666
Role Description Zoom out using Hi-Res Zoom; the zoom ratio decreases while the control is pressed. This option is enabled automatically when [Hi-Res Zoom +] is selected for [Fn1 button]. [Hi-Res Zoom −] Rotate the lens Fn ring counterclockwise to zoom out using Hi-Res Zoom.
Page 667
Role Description [Portrait impression Press the control and rotate a command dial to choose a balance] portrait impression balance mode. Press the control and rotate a command dial to choose a [Metering] metering option for use during video recording. Hold the control and rotate the main command dial to [Focus mode/AF- choose the focus mode, the sub-command dial to choose the area mode]...
Page 668
Power Aperture Power aperture is available only in modes A and M. The display may flicker while aperture is adjusted. g2: Custom Controls...
Command Dials The following roles can be assigned to the command dials. To view options, highlight items and press Role Description Reverse the roles of the main and sub-command dials in selected modes. [Exposure setting] Press 4 or 2 to highlight a mode and 1 or 3 to switch roles. [Focus/AF-area Switch the roles played by rotating the main and sub-command dials while mode selection]...
g3: Control Lock G button U A Custom Settings menu Lock exposure settings or focus-point selection. Option Description Select [ON] to lock shutter speed at its current value in mode M. [Shutter speed lock] O icons appear in the shooting display and control panel when shutter- speed lock is in effect.
g4: Limit AF-Area Mode Selection G button U A Custom Settings menu Choose the AF-area modes that can be selected by pressing the focus-mode button and rotating the sub-command dial. Highlight options and press J or 2 to select (M) or deselect (U). Modes marked with a check (M) are available for selection via the sub-command dial.
g5: Focus Mode Restrictions G button U A Custom Settings menu Limit focus-mode selection to a single focus mode. If an option other than [No restrictions] is selected, rotating the main command dial while holding the focus-mode button will not change the focus mode. g5: Focus Mode Restrictions...
g6: AF Speed G button U A Custom Settings menu Choose the focus speed for video mode. Use [When to apply] to choose when the selected option applies. Option Description [Always] The camera focuses at the selected speed at all times in video mode. [Only while Focus is adjusted at the selected speed only while video recording is in recording]...
g7: AF Tracking Sensitivity G button U A Custom Settings menu The AF tracking sensitivity for video mode can be set to values of from 1 to 7. Choose [7] ([Low]) to help maintain focus on your original subject. If the subject leaves the selected focus point when [1] ([High]) is selected, the camera will respond by quickly shifting focus to a new subject in the same area.
g8: Hi-Res Zoom Speed G button U A Custom Settings menu Choose the zoom speed for Hi-Res Zoom from [Slower], [Standard], and [Faster]. This option only takes effect when Hi-Res Zoom is assigned to a control using any of the [Fn1 button], [Fn2 button], [Lens Fn ring (clockwise)], and [Lens Fn ring (counterclockwise)] options for Custom Setting g2 [Custom controls].
g9: Fine ISO Control (Mode M) G button U A Custom Settings menu Selecting [On (1/6 EV)] allows ISO sensitivity for videos to be adjusted in increments of ¹⁄₆ EV in mode Sensitivity can be set to values of from ISO 64 to 25600 in increments of ¹⁄₆ EV. g9: Fine ISO Control (Mode M)
g10: Extended Shutter Speeds (Mode M) G button U A Custom Settings menu Select [ON] for access to a range of slower shutter speeds in mode M. When [OFF] is selected, the minimum shutter speed varies with frame rate as follows. 120p: ¹⁄₁₂₅ s 100p: ¹⁄₁₀₀...
g11: View Assist G button U A Custom Settings menu Choose [ON] for a live preview of video footage recorded with [N‑Log] selected for video tone mode, but note that the colors in the preview are simplified for enhanced contrast. Colors in the actual recorded footage are unaffected. Contrast is also enhanced when N‑Log footage is viewed on the camera.
g12: Zebra Pattern G button U A Custom Settings menu Choose whether a zebra pattern is used to indicate selected tone ranges in video mode. Pattern Tone Range Choose the tone range shown by the zebra pattern from [Highlights] or [Mid-tones], or select [Zebra pattern off] to turn the zebra pattern off.
Mid-tone Range Choose the brightness needed to trigger the zebra display when [Mid-tones] is selected for [Pattern tone range]. The mid-tone range is defined as a brightness [Value] and [Range] of brightnesses centered around the selected value. Press 4 or 2 to highlight items and press 1 or 3 to change. Zebra Pattern If both the zebra display and focus peaking are enabled in manual focus mode, only focus peaking will take effect.
g13: Limit Zebra Pattern Tone Range G button U A Custom Settings menu Choose the tone ranges accessible via controls to which [Pattern tone range] is assigned. Option Description [Highlights] The control can be used to cycle between [Highlights] and [Zebra pattern off]. [Mid-tones] The control can be used to cycle between [Mid-tones] and [Zebra pattern off].
g14: Grid Type G button U A Custom Settings menu Choose a framing grid for video mode. The selected grid can be displayed by placing a check (M) next to b in the list for Custom Setting g16 [Custom monitor shooting display] or g17 [Custom viewfinder shooting display].
g15: Brightness Information Display G button U A Custom Settings menu Choose how the camera displays brightness information in video mode. Option Description Enable the RGB histogram. [Histogram] [Wave-form The camera displays a wave-form monitor] monitor. The monitor can be displayed at either of two different sizes. [Wave-form monitor (large)] g15: Brightness Information Display...
g16: Custom Monitor Shooting Display G button U A Custom Settings menu Choose the monitor displays accessible by pressing the DISP button in video mode. Highlight items ([Display 2] through [Display 4]) and press J to select (M) or deselect (U). Only displays marked with a check (M) can be accessed by pressing the DISP button during shooting.
Page 685
Option Description [Center indicator] Display crosshairs at the center of the frame. To complete the operation, press G. g16: Custom Monitor Shooting Display...
g17: Custom Viewfinder Shooting Display G button U A Custom Settings menu Choose the viewfinder displays accessible by pressing the DISP button in video mode. Highlight items ([Display 2] or [Display 3]) and press J to select (M) or deselect (U). Only displays marked with a check (M) can be accessed by pressing the DISP button during shooting.
g18: Red REC Frame Indicator G button U A Custom Settings menu If [ON] is selected, a red border will appear around the shooting display while video recording is in progress. This helps prevent missed shots by alerting you when recording is in progress. g18: Red REC Frame Indicator...
The Playback Menu Menu Items and Defaults To display the playback menu, select the D (playback menu) tab in the camera menus. The options in the playback menu are listed below, together with their default settings. [Delete]: — [Playback folder]: All [Playback display options] [Focus point]: U [Mark first shot in series]: U...
Page 689
[Voice memo]: U [Retouched pictures]: U [Series playback] [Sub-selector displays first shot]: ON [Auto series playback]: OFF [List series as single thumbnails]: OFF [Picture review]: Off [After delete]: Show next [After burst, show]: Last picture in burst [Auto-rotate pictures]: ON [Copy image(s)]: —...
Delete G button U D playback menu Delete multiple pictures. For more information, see “Deleting Multiple Pictures” ( 244). Option Description [Selected pictures] Delete selected pictures. [Candidates for Delete pictures rated d (candidate for deletion). deletion] [Pictures shot on Delete all pictures taken on selected dates. selected dates] Delete all pictures in the folder currently selected for [Playback folder] in the playback menu.
Playback Folder G button U D playback menu Choose a folder for playback. Option Description Pictures in all folders with the selected name will be visible during playback. (Folder name) Folders can be renamed using the [Storage folder] > [Rename] option in the photo shooting menu. [All] Pictures in all folders will be visible during playback.
Playback Display Options G button U D playback menu Choose display options for full-frame playback. Highlight options and press 2 to select (M) or deselect (U). To complete the operation, press G. Option Description Select (M) this option to view the location of the focus point used [Focus point] when the picture was taken.
Page 693
Option Description [Basic shooting data] [Flash data] [Picture Control/HLG data] The selected (M) options are included in the full-frame playback [Other shooting data] [Shooting data] display. [Copyright info] [Location data] [IPTC data] Playback Display Options...
Delete Pictures from Both Slots G button U D playback menu Choose whether deleting a copy of a picture recorded to both memory cards with an option other than [Overflow] selected for [Secondary slot function] in the photo shooting menu also deletes the remaining copy. Option Description [Yes (confirmation...
Dual-Format Recording PB Slot G button U D playback menu Choose the slot from which dual-format pictures recorded with [RAW primary - JPEG secondary], [JPEG primary - JPEG secondary], [RAW primary - HEIF secondary], or [HEIF primary - HEIF secondary] selected for [Secondary slot function] in the photo shooting menu are played back. Dual-Format Recording PB Slot...
Filtered Playback Criteria G button U D playback menu Choose the criteria used to choose the pictures displayed during filtered playback ( 239). Filtered Playback Criteria...
Series Playback G button U D playback menu Choose options for viewing bursts. A “burst” refers to a single series of shots taken during burst photography ( 133), treated as a group. Treating the photos in each burst as a group during playback cuts down on the amount of time spent scrolling back and forth to view pictures when the number of shots taken using burst photography is very large.
Picture Review G button U D playback menu Choose whether pictures are automatically displayed immediately after shooting. Option Description Pictures appear in the currently-selected display (monitor or viewfinder) as they are taken. [On] When [Prioritize viewfinder (2)] is selected for monitor mode, the most recent picture will be displayed in the monitor when you take your eye from the viewfinder.
After Delete G button U D playback menu Choose the picture displayed after an image is deleted. Option Description The following picture is displayed. [Show next] If the deleted picture was the last picture, the preceding picture will be displayed. The preceding picture is displayed. [Show previous] If the deleted picture was the first picture, the next picture will be displayed.
After Burst, Show G button U D playback menu Choose whether the photo displayed immediately after a burst of shots is taken in continuous mode is the first or last shot in the burst. This option takes effect only when [Off] is selected for [Picture review] in the playback menu. DSC_0001.jpg DSC_0002.jpg DSC_0003.jpg DSC_0004.jpg DSC_0014.jpg DSC_0015.jpg Most recent shots (burst) Displayed if [First picture in burst] is selected...
Auto-Rotate Pictures G button U D playback menu Select [ON] to display portrait (“tall”) orientation pictures in portrait orientation in the monitor or viewfinder when the camera is held in portrait orientation. When the playback display is in portrait orientation, the 1 and 3 buttons take the roles normally played by the 4 and 2 buttons, while the 4 and 2 buttons take the roles normally played by the 1 and 3 buttons.
Copy Image(s) G button U D playback menu Copy pictures from one memory card to another when two memory cards are inserted. Option Description [Select source] Choose the card from which pictures will be copied. [Select picture(s)] Select pictures to be copied. Select the destination folder on the remaining card (the card not [Select destination folder] selected for [Select source]).
Page 703
Choose [Select picture(s)]. Highlight [Select picture(s)] and press 2 to view the [Select picture(s)] display. Select the source folder. Highlight the folder containing the pictures to be copied and press 2 to display the [Images selected by default] menu. To copy all pictures from the card in the selected slot, highlight [All pictures in slot], press J, and proceed to Step 10.
Page 704
Select additional pictures. Highlight pictures and press the W (Q) button to select; selected pictures are marked with a check ( ). To remove the check ( ) and deselect the current picture, press the W (Q) button again. To view the highlighted picture full screen, press and hold the X button.
Page 705
Choose a destination folder. Highlight one of the following options and press 2. Option Description Enter the number of the destination folder ( 425). If a folder with the selected number does not already [Select folder exist, a new folder will be created. by number] Choose the destination folder from a list of existing folders.
Page 706
Choose [Yes]. The camera will display the message “Copy?” together with the number of pictures that will be copied. Highlight [Yes] and press J to copy the selected pictures. Press J again to exit when copying is complete. Cautions: Copying Pictures Pictures will not be copied if there is insufficient space on the destination card.
The Setup Menu Menu Items and Defaults To view the setup menu, select the B tab in the camera menus. The options in the setup menu are listed below, together with their default settings. [Format memory card]: — [Language]: (Default varies with country of purchase) [Time zone and date] [Time zone]: (Default varies with country of purchase) [Date and time]: —...
Page 708
[Focal length (mm)]: – – [Maximum aperture]: – – [Save focus position]: OFF [Auto temperature cutout]: Standard [Sensor shield behavior at power off]: Sensor shield stays open [Clean image sensor] [Automatic cleaning]: Clean at shutdown [Image Dust Off ref photo]: — [Pixel mapping]: — [Image comment] [Attach comment]: OFF [Copyright info]...
Page 709
[Assign remote (WR) Fn button]: None [Conformity marking]: — [Battery info]: — [USB power delivery]: ON [Energy saving (photo mode)]: OFF [Slot empty release lock]: Enable release [Save/load menu settings]: — [Reset all settings]: — [Firmware version]: — Displayed only when a GNSS device is connected. Menu Items and Defaults...
Format Memory Card G button U B setup menu Format memory cards. Memory cards that have been formatted in a computer or another camera should be reformatted using this option before use. To begin formatting, choose a memory card slot and select [Yes]. Note that formatting permanently deletes all pictures and other data on the card. Before formatting, be sure to make backup copies as required.
“Yes (Full Format)” When formatting compatible CFexpress memory cards, instead of a simple [Yes] you will be presented with [Yes (full format)] and [Yes (quick format)] options after selecting the memory card slot. Select [Yes (full format)] to perform a full format, deleting data from all areas of the card. This option is recommended for users who wish to ensure that all data are deleted or who feel that the speed at which the camera reads from and writes to the card has slowed and wish to improve data transfer speeds.
Language G button U B setup menu Choose a language for camera menus and messages. The languages available vary with the country or region in which the camera was originally purchased. Language...
Time Zone and Date G button U B setup menu Change time zones and set the camera clock. We recommend that the camera clock be adjusted regularly. Option Description Choose a time zone. The time selected for [Date and time] is [Time zone] automatically adjusted for the new time zone.
Monitor Brightness G button U B setup menu Press 1 or 3 to adjust monitor brightness. Choose higher values for increased brightness, lower values for reduced brightness. [Monitor brightness] can only be adjusted when the monitor is the active display. It cannot be adjusted when [Viewfinder only] is selected for monitor mode or when your eye is to the viewfinder.
Monitor Color Balance G button U B setup menu Adjust monitor color balance to your taste. [Monitor color balance] can only be adjusted when the monitor is the active display. It cannot be adjusted when [Viewfinder only] is selected for monitor mode or when your eye is to the viewfinder.
Viewfinder Brightness G button U B setup menu Adjust viewfinder brightness. [Viewfinder brightness] can only be adjusted when the viewfinder is the active display. It cannot be adjusted when the monitor is on or when [Monitor only] is selected for monitor mode. Option Description [Auto] Viewfinder brightness is adjusted automatically in response to lighting conditions.
Viewfinder Color Balance G button U B setup menu Adjust viewfinder color balance to your taste. [Viewfinder color balance] can only be adjusted when the viewfinder is the active display. It cannot be adjusted when the monitor is on or when [Monitor only] is selected for monitor mode. Otherwise the procedure is the same as for [Monitor color balance] ( 715).
Finder Display Size (Photo Lv) G button U B setup menu Choose a magnification for the viewfinder display from [Standard] and [Small]. Selecting [Small] makes it easier to see the entire subject. Finder Display Size (Photo Lv)
Limit Monitor Mode Selection G button U B setup menu Choose the monitor modes that can be selected using the M button. Highlight options and press J or 2 to select (M) or deselect (U). Options marked with a check (M) are available for selection. To complete the operation, press G.
Auto Rotate Info Display G button U B setup menu When [ON] is selected, the indicators in the shooting and playback displays will automatically be rotated to match camera orientation. Auto Rotate Info Display...
AF Fine-Tuning Options G button U B setup menu Fine-tune focus for the current lens. Use only as required. We recommend that you perform fine-tuning at a focus distance you use frequently. If you perform focus-tuning at a short focus distance, for example, you may find it less effective at longer distances.
Page 722
Option Description [Choose value for Choose from multiple fine-tuning values saved for lenses of the same type. current lens] Deleting Saved Values To delete values saved using [Fine-tune and save lens], highlight the desired lens in the [List saved values] list and press O (Q). AF Fine-Tuning Options...
Creating and Saving Fine-Tuning Values Attach the lens to the camera. Select [AF fine-tuning options] in the setup menu, then highlight [Fine-tune and save lens] and press 2. An AF fine-tuning dialog will be displayed. Press 4 or 2 to fine-tune autofocus. Choose from values between +20 and −20.
Choosing a Default Fine-Tuning Value Select [AF fine-tuning options] in the setup menu, then highlight [Default] and press 2. Press 4 or 2 to fine-tune autofocus. Choose from values between +20 and −20. The current value is shown by g, the previously-selected value by o. The larger the fine-tuning value, the farther the focal point is from the lens;...
Non-CPU Lens Data G button U B setup menu Record data for non-CPU lenses attached using an optional mount adapter. Recording the focal length and maximum aperture of non-CPU lenses allows them to be used with some camera features normally reserved for CPU lenses, such as on-board vibration reduction. Option Description [Lens number]...
Save Focus Position G button U B setup menu When [ON] is selected, the camera will save the current focus position when turned off and restore it when next turned on. Note that this increases camera startup times. Note that even when [ON] is selected, if the temperature, zoom position, or other conditions change while the camera is off, focus may resume from a different position when the camera is turned on.
Auto Temperature Cutout G button U B setup menu The level at which the camera will turn off automatically as its internal temperature rises can be selected from [Standard] and [High]. When [Standard] is selected, the camera will display first a J and then a K icon as its internal temperature rises, switching to a count-down timer if the temperature increases still further.
Sensor Shield Behavior at Power Off G button U B setup menu If [Sensor shield closes] is selected, the shield in front of the image sensor will close when the camera is turned off. This prevents dust or other foreign matter collecting on the image sensor when lenses are exchanged.
Clean Image Sensor G button U B setup menu Dirt or dust entering the camera when lenses are exchanged or the body cap is removed may adhere to the image sensor and affect your photographs. The “clean image sensor” option vibrates the sensor to remove dust.
Image Dust Off Ref Photo G button U B setup menu Acquire reference data for the Image Dust Off option in NX Studio. Image Dust Off processes NEF (RAW) pictures to mitigate effects caused by dust adhering to the front of the camera image sensor. For more information, refer to NX Studio’s online help.
Page 731
Press the shutter-release button the rest of the way down to acquire Image Dust Off reference data. The monitor turns off when the shutter-release button is pressed. If the reference object is too bright or too dark, the camera may be unable to acquire Image Dust Off reference data, in which case a message will appear and the camera will return to the display shown in Step 1.
Pixel Mapping G button U B setup menu Pixel mapping checks and optimizes the camera image sensor. If you notice unexpected bright spots appearing in pictures taken with the camera, perform pixel mapping as described below. Pixel mapping is available only when a Z mount lens or an optional FTZ II/FTZ mount adapter is attached.
Image Comment G button U B setup menu Add a comment to new photographs as they are taken. Comments can be viewed in the NX Studio [Info] tab. Input Comment Input a comment of up to 36 characters. Highlight [Input comment] and press 2 to display a text-entry dialog.
[Attach copyright information] before lending or transferring the camera to another person. You will also need to make sure that the artist and copyright fields are blank. Nikon does not accept liability for any damages or disputes arising from the use of the [Copyright information] option.
IPTC G button U B setup menu IPTC presets can be created or edited on the camera and embedded in new photographs as described below. You can also load IPTC presets created on a computer. To create IPTC presets and save them to memory cards for later import, use IPTC Preset Manager 739).
Embedding Presets Highlighting [Auto embed during shooting] and pressing 2 displays a list of presets. Highlight a preset and press J; the selected preset will be embedded in all subsequent photographs. To disable embedding, select [Off]. Viewing IPTC Data Embedded presets can be viewed on the [IPTC data] page in the photo information display. To display the [IPTC data] page, select (M) both [Shooting data] and [IPTC data] for [Playback display options] in the playback menu.
Copying Presets to the Camera The camera can store up to ten presets; to copy IPTC presets from a memory card to a selected destination on the camera, select [Load/save] > [CFexpress/XQD card slot] or [SD card slot], then highlight [Copy to camera] and press 2. Highlight a preset and press J to proceed to the [Select destination] list.
Page 738
Cautions: IPTC Information The camera supports standard roman alphanumeric characters only. Other characters will not display correctly except on a computer. Preset names ( 735) may be up to 18 characters long. If a preset with a longer name is created using a computer, all characters after the eighteenth will be deleted.
Page 739
IPTC IPTC is a standard established by the International Press Telecommunications Council (IPTC) with the intent of clarifying and simplifying the information required when photographs are shared with a variety of publications. IPTC Preset Manager IPTC presets can be created on a computer and saved to memory cards using IPTC Preset Manager software.
Voice Memo Options G button U B setup menu Adjust settings for voice memos ( 286, 288). Voice Memo Control Choose the behavior of controls to which [Voice memo] has been assigned via Custom Setting f3 [Custom controls (playback)]. Option Description Voice memos up to 60 seconds long can be recorded while the control [Press and hold] is pressed.
Audio Output (Playback) Choose the device used for voice memo playback. Option Description Voice memos are played back over headphones (if connected) or the camera’s built-in speaker. [Speaker/ Press 1 or 3 to choose a volume headphones] between [1] and [15]. Press J to save changes and exit.
Camera Sounds G button U B setup menu Shutter Sound Choose whether the camera makes a sound when the shutter is released. Selecting [OFF] disables the shutter-release sound. Beep On/Off Turn the beep speaker on or off. If [On] is selected for [Beep on/off], beeps sound when: the self-timer counts down, interval-timer photography, time-lapse video recording, or focus shift ends, the camera focuses in photo mode (note that this does not apply if AF‑C is selected for focus...
Volume Adjust beep volume and the volume of the shutter-release sound. Pitch Choose the pitch of the beep from [High] and [Low]. The pitch of the shutter sound cannot be changed. Silent Mode Selecting [ON] for [Silent mode] in the setup menu disables the shutter-release sound and beep speaker.
Silent Mode G button U B setup menu Select [ON] to override the options selected for [Camera sounds] in the setup menu and mute the electronic shutter and beep speaker during photography. Selecting [ON] also suppresses other camera sounds. It does not, however, completely silence the camera.
Touch Controls G button U B setup menu Adjust settings for monitor touch controls. Enable/Disable Touch Controls Enable or disable touch controls. Select [Playback only] to enable touch controls in playback mode only. Glove Mode Selecting [ON] raises the sensitivity of the touch screen, making it easier to use while wearing gloves. Touch Controls...
USB Connection Priority G button U B setup menu Choose the function assigned priority when the camera is connected to a computer via USB. Option Description The monitor remains blank while the camera is connected to a computer. The monitor [Upload] turns on when the shutter-release button is pressed halfway but upload speeds may drop.
Location Data G button U B setup menu This item is available only when a GNSS device is connected. Use it to adjust location data settings or view location data. Option Description If [OFF] is selected, the standby timer will not expire regardless of the option selected for Custom Setting c3 [Power off delay] >...
A WR‑A10 adapter is required when using the WR‑R10. Be sure the firmware for the WR‑R10 has been updated to the latest version (version 3.0 or later). For information on firmware updates, see the Nikon website for your area. LED Lamp Enable or disable the status LEDs on the WR‑R11a or WR‑R10 wireless remote controller mounted on...
Link Mode Choose a link mode for WR‑R11a or WR‑R10 wireless remote controllers mounted on other cameras or radio-controlled flash units that support Advanced Wireless Lighting. Be sure that the same mode is selected for the other devices. Option Description The camera connects only to devices with which it has previously been paired.
Assign Remote (WR) Fn Button G button U B setup menu Choose the role played by the Fn button on optional wireless remote controllers equipped with an Fn button. See Custom Setting f2 [Custom controls (shooting)] for more information. Option [AF-ON] [AF lock only] [AE lock (Reset on release)] [AE lock only] [AE/AF lock]...
Battery Info G button U B setup menu View information on the battery currently inserted in the camera. Option Description [Charge] The current battery level, expressed as a percentage. [No. of shots] The number of pictures taken since the battery was last charged. A five-level display showing battery age.
USB Power Delivery G button U B setup menu Choose whether the camera draws power from devices connected via the USB Power Delivery connector. USB power delivery allows the camera to be used while limiting the drain on the battery. Option Description The camera draws power from connected devices while on. Connected devices will also [ON] supply power when the camera is off if Bluetooth upload is in progress or the memory card access lamp is lit.
Page 755
Computer USB Power Delivery Before using a computer to supply power to the camera, check that the computer is equipped with a Type C USB connector. Use an optional UC-E25 USB cable with Type C connectors at both ends to connect the camera to the computer.
Energy Saving (Photo Mode) G button U B setup menu In photo mode, the shooting display will dim to save power approximately 15 seconds before the standby timer expires. Option Description [ON] Enable energy saving. The display refresh rate may drop. Disable energy saving. Note selecting [OFF] does not stop the shooting display dimming [OFF] a few seconds before the standby timer expires.
Slot Empty Release Lock G button U B setup menu Choose whether the shutter can be released when no memory card is inserted in the camera. Option Description [Release locked] The shutter cannot be released when no memory card is inserted. The shutter can be released with no memory card inserted. No pictures [Enable release] will be recorded;...
Save/Load Menu Settings G button U B setup menu Save current camera menu settings to a memory card. You can also load saved settings, allowing menu settings to be shared among cameras of the same model. If two memory cards are inserted, the settings will be saved to the card selected for [Primary slot selection] in the photo shooting menu.
Page 759
[Flash control] [Flash mode] [Flash compensation] [Focus mode] [AF-area mode] [AF subject detection options] [Vibration reduction] (the options available vary with the lens) [Auto bracketing] VIDEO RECORDING MENU [Shooting menu bank] [Extended menu banks] [File naming] [Destination] [Video file type] [Frame size/frame rate] [Video quality (N-RAW)] [Image area]...
Page 760
[Timecode] (excepting [Timecode origin]) [External rec. cntrl (HDMI)] [Hi-Res Zoom] CUSTOM SETTINGS MENU: All items PLAYBACK MENU [Playback display options] [Delete pictures from both slots] [Dual-format recording PB slot] [Filtered playback criteria] [Series playback] [Picture review] [After delete] [After burst, show] [Auto-rotate pictures] SETUP MENU [Language]...
RECENT SETTINGS The current contents of the recent settings menu (up to 20 items) [Choose tab] Save Menu Settings Save settings to a memory card. If the card is full, an error will be displayed and settings will not be saved.
Reset All Settings G button U B setup menu Reset all settings except [Language] and [Time zone and date] to their default values. Copyright information and other user-generated entries are also reset. Once reset, settings cannot be restored. We recommend that you save settings using the [Save/load menu settings] item in the setup menu before performing a reset.
Tip: Firmware Updates Updates can be performed using a computer or smart device. Computer: Check the Nikon Download Center for new firmware. For more information, see the firmware download page. Smart device: If the smart device has been paired with the camera using the SnapBridge app, the app will automatically notify you when updates become available, and you can then download the update to the camera memory card via the smart device.
The Network Menu Menu Items and Defaults To view the network menu, select the F tab in the camera menus. The options in the network menu are listed below, together with their default settings. [Airplane mode]: OFF [Connect to smart device] [Pairing (Bluetooth)] [Bluetooth connection]: OFF [Select pictures for upload]...
Page 765
[Upload folder]: — [Deselect all?]: — [Connect to FTP server] [Network settings]: — [Options] [Auto upload]: OFF [Delete after upload]: OFF [Upload RAW + JPEG as] [Overflow/backup]: RAW + JPEG [RAW primary - JPEG secondary]: RAW + JPEG [Upload RAW + HEIF as] [Overflow/backup]: RAW + HEIF [RAW primary - HEIF secondary]: RAW + HEIF [JPEG+JPEG slot selection]: Primary slot...
Connect to Smart Device G button U F network menu Connect to smartphones or tablets (smart devices) via Bluetooth or Wi-Fi. Pairing (Bluetooth) Pair with or connect to smart devices using Bluetooth. Option Description [Start pairing] Pair the camera with a smart device ( 302).
Wi-Fi Connection Connect to smart devices via Wi-Fi. Establish Wi-Fi Connection Initiate a Wi-Fi connection to a smart device. The camera SSID and password will be displayed. To connect, select the camera SSID on the smart device and enter the password ( 305).
Upload While Off If [ON] is selected, upload of pictures to smart devices via wireless connections will continue even when the camera is off. Location Data (Smart Device) Display latitude, longitude, altitude, and UTC (Universal Coordinated Time) data downloaded from a smart device.
Connect to Computer G button U F network menu Connect to computers via Ethernet or wireless LAN. Network Settings Add camera network profiles. This item can also be used to choose from existing network profiles. Create Profile Create new network profiles ( 315, 329).
Page 771
Option Description Display connection settings for connection to wireless networks. Infrastructure mode: Adjust settings for connection to a network via a router. [SSID]: Enter the network SSID. [Channel]: Selected automatically. [Authentication/encryption]: Select the type of encryption used on the wireless network. [Password]: Enter the network password.
Copy to/from Card Share network profiles. If two memory cards are inserted, the profiles will be copied to and from the card in the slot selected for [Primary slot selection] in the photo shooting menu. Option Description Copy profiles from the root directory of the memory card to the [Copy profile from card] camera profile list.
Options Adjust upload settings. Auto Upload Select [ON] to mark new photos for upload as they are taken. Upload begins only after the photo has been recorded to the memory card. Be sure a memory card is inserted in the camera. Videos are not uploaded automatically.
Page 774
Upload RAW + HEIF As When uploading RAW + HEIF pictures, choose whether to upload both the NEF (RAW) and HEIF files or only the NEF (RAW) or HEIF copy. Separate options can be selected for [Overflow/backup] and [RAW primary - HEIF secondary]. The option selected for [Overflow/backup] takes effect during both auto and manual upload.
Connect to FTP Server G button U F network menu Connect to FTP servers via Ethernet or wireless LAN. Network Settings Add camera network profiles. This item can also be used to choose from existing network profiles. Create Profile Create new network profiles ( 336, 352).
Page 776
Option Description Adjust TCP/IP settings for infrastructure connections. An IP address is required. [Obtain automatically]: If [ON] is selected, the IP address and sub-net mask for infrastructure mode connections will be acquired via a DHCP server or automatic IP addressing. Select [OFF] to enter the IP address ([Address]) and sub-net mask [TCP/IP] ([Mask]) manually.
Page 777
Copy to/from Card Share network profiles. If two memory cards are inserted, the profiles will be copied to and from the card in the slot selected for [Primary slot selection] in the photo shooting menu. Option Description Copy profiles from the root directory of the memory card to the [Copy profile from card] camera profile list.
Options Adjust upload settings. Auto Upload Select [ON] to mark new photos for upload as they are taken. Upload begins only after the photo has been recorded to the memory card. Be sure a memory card is inserted in the camera. Videos are not uploaded automatically.
Page 779
JPEG + JPEG Slot Selection Choose a source slot for auto upload when taking pictures with [JPEG primary - JPEG secondary] selected for [Secondary slot function] in the photo shooting menu. HEIF + HEIF Slot Selection Choose a source slot for auto upload when taking pictures with [HEIF primary - HEIF secondary] selected for [Secondary slot function] in the photo shooting menu.
Page 780
Deselect All? Remove upload marking from all pictures. Upload of pictures with an “uploading” icon will immediately be terminated. Manage Root Certificate Load or manage root certificates used for connection to FTPS servers. Contact the network administrator for the FTPS server in question for information on acquiring root certificates.
Connect to Other Cameras G button U F network menu Connect to other cameras for shutter or clock synchronization. Synchronized Release Select [ON] to synchronize the shutter release with those of cameras on the same network. Network Settings Add camera network profiles. This item can also be used to choose from existing network profiles. Create Profile Create new network profiles ( 371).
Page 782
Copy to/from Card Share network profiles. If two memory cards are inserted, the profiles will be copied to and from the card in the slot selected for [Primary slot selection] in the photo shooting menu. Option Description Copy profiles from the root directory of the memory card to the [Copy profile from card] camera profile list.
Group Name Choose a group for synchronized release. Shutter release is synchronized across the cameras on the network that are in the same group. Master/Remote Choose a role for each camera from “master” and “remote”. Pressing the shutter-release button on the master camera releases the shutters on all remote cameras that are both on the same network and in the same group.
ATOMOS AirGlu BT Options G button U F network menu Manage wireless Bluetooth connections between the camera and Atomos UltraSync BLUE AirGlu accessories. The UltraSync BLUE can be used for simultaneous wireless connections to multiple compatible cameras or audio recorders. Time codes are transmitted to the connected devices from the UltraSync BLUE, synchronizing time codes even across devices from a mix of manufacturers.
Page 785
Cautions: Using the UltraSync BLUE Time codes will not be recorded if [H.264 8-bit (MP4)] is selected for [Video file type] in the video recording menu. The UltraSync BLUE allows users to choose the frame rate. If the value is not a match for that chosen with the camera, time codes will not be recorded or output via HDMI.
USB Data Connection G button U F network menu Adjust settings for connection to other devices via the camera’s USB data connector. Select [MTP/PTP] when connecting to computers or Android devices via USB. Select [iPhone] when connecting to iPhones via a third-party USB‑C to Lightning cable in order to use NX MobileAir (for information on compatible USB‑C to Lightning cables, see the online help for NX MobileAir).
Router Frequency Band G button U F network menu Choose the band for the selected SSID when connecting to a wireless network in infrastructure mode. Select [2.4 GHz/5 GHz] to connect to networks operating on either band. When the camera searches for networks active in the vicinity, it will list only those operating on the chosen band or bands.
My Menu/Recent Settings Menu Items and Defaults To view [MY MENU], select the O tab in the camera menus. The options in “My Menu” are listed below, together with their default settings. [Add items]: — [Remove items]: — [Rank items]: — [Choose tab]: MY MENU Menu Items and Defaults...
My Menu: Creating a Custom Menu G button U O my menu My Menu can be used to create and edit a customized list of up to 20 items from the photo shooting, video recording, Custom Settings, playback, setup, and network menus. Items can be added, deleted, and reordered as described below.
Page 791
Position the new item. Press 1 or 3 to position the new item and press J to add it to My Menu. Add more items. The items currently displayed in My Menu are indicated by a check mark (L). Items indicated by a V icon cannot be selected. Repeat Steps 1–4 to select additional items.
Removing Items from My Menu Select [Remove items] in [O MY MENU]. Highlight [Remove items] and press 2. Select items. Highlight items and press J or 2 to select (M) or deselect. Continue until all the items you wish to remove are selected (L).
Reordering Items in My Menu Select [Rank items] in [O MY MENU]. Highlight [Rank items] and press 2. Select an item. Highlight the item you wish to move and press J. Position the item. Press 1 or 3 to move the item up or down in My Menu and press J.
Displaying “RECENT SETTINGS” Select [Choose tab] in [O MY MENU]. Highlight [Choose tab] and press 2. Select [m RECENT SETTINGS]. Highlight [m RECENT SETTINGS] in the [Choose tab] menu and press J. The name of the menu will change from [MY MENU] to [RECENT SETTINGS] and the tab icon will change from O to m.
Recent Settings: Accessing Recently-Used Settings G button U m RECENT SETTINGS How Items Are Added to “RECENT SETTINGS” Menu items are added to the top of the [RECENT SETTINGS] menu as they are used. The twenty most recently-used settings are listed. Removing Items from the Recent Settings Menu To remove an item from the [RECENT SETTINGS] menu, highlight it and press the O (Q) button;...
Before Contacting Customer Support You may be able to resolve any issues with the camera by following the steps below. Check this list before consulting your retailer or Nikon-authorized service representative. Check the list of common problems. Common problems and solutions are listed in the following sections: “Problems and Solutions”...
Page 797
Restoring Default Settings Depending on current settings, some menu items and other features may be unavailable. To access menu items that are grayed out or features that are otherwise unavailable, try restoring default settings using the [Reset all settings] item in the setup menu. Note, however, that wireless network profiles, copyright information, and other user-generated entries will also be reset.
Problems and Solutions Solutions to some common issues are listed below. Battery/Display ● The camera is on but does not respond: Wait for recording and other operations to end. If the problem persists, turn the camera off. If the camera does not turn off, remove and reinsert the battery. If you are using an AC adapter, disconnect and reconnect the AC adapter.
Page 799
● The display in the control panel, viewfinder, or monitor turns off without warning: Choose longer delays for Custom Setting c3 [Power off delay]. ● The control panel is unresponsive and dim: Control panel response times and brightness vary with temperature. ●...
Shooting ● The camera takes time to turn on: More time will be needed to find files if the memory card contains large numbers of files or folders. ● The shutter cannot be released: Is a memory card inserted, and if so, does it have space available? If you selected mode S after selecting a shutter speed of “Bulb”...
Page 801
● The beep does not sound: Is [ON] selected for [Silent mode] in the setup menu? A beep does not sound when the camera focuses with AF‑C selected for focus mode. Select an option other than [Off] for [Camera sounds] > [Beep on/off] in the setup menu. The beep does not sound in video mode.
Page 802
● Photographs and videos do not appear to have the same exposure as the preview shown in the display: The effects of changes to settings that affect exposure and color are not visible in the display when [Adjust for ease of viewing] is selected for Custom Setting d8 [View mode (photo Lv)]. Note that even when [Show effects of settings] is selected for Custom Setting d8, display brightness will be adjusted for ease of viewing (per [Adjust for ease of viewing]) in mode M when a flash unit is attached.
Page 803
● Shooting ends unexpectedly or does not start: Shooting may end automatically to prevent the camera overheating, for example if: the ambient temperature is high, the camera has been used for extended periods to record videos, or the camera has been used in continuous release modes for extended periods. If pictures cannot be taken because the camera is running hot, turn the camera off and wait for it to cool before trying to take pictures again.
Page 804
● The effects of [Set Picture Control] differ from picture to picture: [Auto] is selected for [Set Picture Control] or as the basis for a custom Picture Control created using [Manage Picture Control], or [A] (auto) is selected for [Quick sharp], [Contrast], or [Saturation].
Playback ● NEF (RAW) pictures are not visible during playback: The camera displays only the JPEG or HEIF copies of pictures taken with [RAW + JPEG/HEIF finem], [RAW + JPEG/HEIF fine], [RAW + JPEG/HEIF normalm], [RAW + JPEG/HEIF normal], [RAW + JPEG/HEIF basicm], or [RAW + JPEG/HEIF basic] selected for [Image quality]. ●...
Page 806
● The camera displays the message, “Folder contains no pictures.”: Select [All] for [Playback folder] in the playback menu. ● NEF (RAW) pictures cannot be printed: Print JPEG or HEIF copies of the pictures created using a tool such as the [RAW processing (current picture)] or [RAW processing (multiple pictures)] items accessible via [Retouch] in the playback i menu.
Page 807
● The effects of [Set Picture Control], [Set Picture Control (HLG)], [Active D-Lighting], or [Vignette control] are not visible: In the case of NEF (RAW) pictures, the effects can only be viewed using Nikon software. View NEF (RAW) pictures using NX Studio.
Bluetooth and Wi-Fi (Wireless Networks) ● Smart devices do not display the camera SSID (network name): Navigate to the network menu and confirm both that [OFF] is selected for [Airplane mode] and that [ON] is selected for [Connect to smart device] > [Pairing (Bluetooth)] > [Bluetooth connection].
Miscellaneous ● The date of recording is not correct: Is the camera clock set correctly? The clock is less accurate than most watches and household clocks; check it regularly against more accurate timepieces and reset as necessary. ● Menu items cannot be selected: Some items are not available at certain combinations of settings.
Alerts and Error Messages This section lists the alerts and error messages that appear in the control panel and camera display. Alerts The following alerts appear in the control panel and camera display: Alert Problem/solution Camera display Control panel Low battery. Ready a spare battery.
Page 811
Alert Problem/solution Camera display Control panel Subject too bright; limits of camera exposure metering system exceeded. Lower ISO sensitivity. Mode P: Use third-party ND (neutral density) filter (filter can also be used if alert is still displayed after following settings are adjusted in mode S or Mode S: Choose faster shutter speed.
Page 812
Camera display Control panel Camera malfunction. Press shutter-release button again. If error persists or Err (flashes) appears frequently, consult Nikon-authorized service representative. The memory card is write-protected (“locked”). Card (flashes) Slide the lock switch to the “write” position ( 83).
Shutter release disabled. — Replace with spare battery. Recharge battery. Charge battery. Battery info not available. Battery cannot be used. Contact Nikon- This battery is unable to — authorized service representative. provide data to the camera Battery level is extremely low; charge and cannot be used.
Page 814
Update to the latest version of the mount version not supported. — adapter firmware. For more information, visit Upgrade FTZ firmware. the Nikon website for your country or region. Memory card does not support required video write speed. Recording interrupted. Please —...
Page 815
Message Problem/solution Camera display Control panel Selected picture cannot be retouched. Retouch options are available only with Cannot select this file. — pictures taken with or previously retouched on camera. Selected video cannot be edited. Videos created with other devices cannot This video cannot be edited.
The latest firmware is available from the Nikon Download Center. For more information on lenses, see the lens documentation available from the Nikon Download Center.
Camera Displays The displays show information on current settings. Other icons or warnings may occasionally be displayed, for example when settings are changed. The Monitor Photo Mode 9 10 14 15 16 Camera Displays...
Page 818
Shooting mode ( 121) FTP connection status ( 336, 352) Flexible program indicator ( 122) Exposure indicator AF-area brackets ( 107) Exposure ( 124) Temperature warning ( 727) Exposure compensation ( 131) Release mode ( 133) Auto bracketing ( 162) Interval-timer photography indicator Remote camera connection status 483)
Page 819
Temperature Warnings If the camera temperature becomes elevated, a temperature warning and count-down timer will be displayed. When the timer reaches zero, the shooting display will turn off. The temperature at which the count-down timer starts can be selected from [Standard] and [High] using [Auto temperature cutout] in the setup menu.
Compatible Flash Units The Nikon Creative Lighting System (CLS) Nikon’s advanced Creative Lighting System (CLS) supports a variety of features thanks to improved communication between the camera and compatible flash units. Features Available with CLS-Compatible Flash Units Flash unit SB‑5000 SB‑910/SB‑900/SB‑800...
Page 831
The SB‑5000 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash 2 Auto aperture Non-TTL auto — Distance-priority manual Manual Repeating flash Compatible Flash Units...
Page 832
Supported features Optical Advanced Wireless Lighting Master Remote flash control i‑TTL i‑TTL [A : B] Quick wireless flash control Auto aperture Non-TTL auto — Manual Repeating flash Remote i‑TTL i‑TTL [A : B] Quick wireless flash control 3 ...
Page 833
Supported features Camera modeling illumination Unified flash control Camera flash unit firmware update Not available with spot metering. Can also be selected via the flash unit. Choice of qA and A depends on the option selected with the master flash. Supports the same features as remote flash units with optical AWL.
Page 834
The SB‑910, SB‑900, and SB‑800 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash 2 Auto aperture 3 3 Non-TTL auto Distance-priority manual Manual Repeating flash Compatible Flash Units...
Page 835
Supported features Optical Advanced Wireless Lighting Master Remote flash control i‑TTL i‑TTL [A : B] Quick wireless flash control — Auto aperture Non-TTL auto — Manual Repeating flash Remote i‑TTL i‑TTL [A : B] Quick wireless flash control 4 ...
Page 836
Supported features Camera modeling illumination Unified flash control — 7 Camera flash unit firmware update Not available with spot metering. Can also be selected via the flash unit. qA/A mode selection is performed on the flash unit using custom settings. Choice of qA and A depends on the option selected with the master flash.
Page 837
The SB‑700 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash Auto aperture — Non-TTL auto — Distance-priority manual Manual Repeating flash — Compatible Flash Units...
Page 838
Supported features Optical Advanced Wireless Lighting Master Remote flash control i‑TTL i‑TTL [A : B] Quick wireless flash control Auto aperture — Non-TTL auto — Manual Repeating flash — Remote i‑TTL i‑TTL [A : B] Quick wireless flash control ...
Page 839
Supported features Camera modeling illumination Unified flash control — Camera flash unit firmware update Not available with spot metering. Available only in i‑TTL, GN, and M flash-control modes. Available only in i‑TTL flash-control mode. Compatible Flash Units...
Page 840
The SB‑600 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash 2 Auto aperture — Non-TTL auto — Distance-priority manual — Manual Repeating flash — Compatible Flash Units...
Page 841
Supported features Optical Advanced Wireless Lighting Master Remote flash control — i‑TTL i‑TTL — [A : B] Quick wireless flash control — Auto aperture — Non-TTL auto — Manual — Repeating flash — Remote i‑TTL i‑TTL [A : B] Quick wireless flash control ...
Page 842
Supported features Camera modeling illumination Unified flash control — Camera flash unit firmware update — Not available with spot metering. Can also be selected via the flash unit. Available only in i‑TTL and M flash-control modes. Available only in i‑TTL flash-control mode. Compatible Flash Units...
Page 843
The SB‑500 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash Auto aperture — Non-TTL auto — Distance-priority manual — Manual 2 Repeating flash — Compatible Flash Units...
Page 844
Supported features Optical Advanced Wireless Lighting Master 2 Remote flash control 2 i‑TTL i‑TTL [A : B] Quick wireless flash control — Auto aperture — Non-TTL auto — Manual 2 Repeating flash — Remote i‑TTL i‑TTL [A : B] Quick wireless flash control ...
Page 845
Supported features Camera modeling illumination Unified flash control Camera flash unit firmware update Not available with spot metering. Can be selected using the [Flash control] item in the camera menus. Available only in i‑TTL and M flash-control modes. Available only in i‑TTL flash-control mode. Compatible Flash Units...
Page 846
The SB‑R200 Supported features Stand-alone i‑TTL balanced fill-flash — i‑TTL Standard i‑TTL fill-flash — Auto aperture — Non-TTL auto — Distance-priority manual — Manual — Repeating flash — Compatible Flash Units...
Page 847
Supported features Optical Advanced Wireless Lighting Master Remote flash control — i‑TTL i‑TTL — [A : B] Quick wireless flash control — Auto aperture — Non-TTL auto — Manual — Repeating flash — Remote i‑TTL i‑TTL [A : B] Quick wireless flash control ...
Page 848
Supported features Camera modeling illumination Unified flash control — Camera flash unit firmware update — Available only in i‑TTL and M flash-control modes. Available only in i‑TTL flash-control mode. Compatible Flash Units...
Page 849
The SB‑400 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash Auto aperture — Non-TTL auto — Distance-priority manual — Manual 2 Repeating flash — Compatible Flash Units...
Page 850
Supported features Optical Advanced Wireless Lighting Master Remote flash control — i‑TTL i‑TTL — [A : B] Quick wireless flash control — Auto aperture — Non-TTL auto — Manual — Repeating flash — Remote i‑TTL i‑TTL — [A : B] Quick wireless flash control —...
Page 851
Supported features Camera modeling illumination — Unified flash control Camera flash unit firmware update — Not available with spot metering. Can be selected using the [Flash control] item in the camera menus. Available only in i‑TTL flash-control mode. Compatible Flash Units...
Page 852
The SB‑300 Supported features Stand-alone 1 i‑TTL balanced fill-flash i‑TTL Standard i‑TTL fill-flash Auto aperture — Non-TTL auto — Distance-priority manual — Manual 2 Repeating flash — Compatible Flash Units...
Page 853
Supported features Optical Advanced Wireless Lighting Master Remote flash control — i‑TTL i‑TTL — [A : B] Quick wireless flash control — Auto aperture — Non-TTL auto — Manual — Repeating flash — Remote i‑TTL i‑TTL — [A : B] Quick wireless flash control —...
Page 854
Supported features Camera modeling illumination — Unified flash control Camera flash unit firmware update Not available with spot metering. Can be selected using the [Flash control] item in the camera menus. Available only in i‑TTL flash-control mode. Compatible Flash Units...
Page 855
The SU-800 Wireless Speedlight Commander When mounted on a CLS-compatible camera, the SU-800 can be used as a commander for SB‑5000, SB‑910, SB‑900, SB‑800, SB‑700, SB‑600, SB‑500, or SB‑R200 flash units. Group flash control is supported for up to three groups. The SU-800 itself is not equipped with a flash. Supported features Stand-alone i‑TTL balanced fill-flash...
Page 856
Supported features Optical Advanced Wireless Lighting Master Remote flash control i‑TTL i‑TTL — 1 [A : B] Quick wireless flash control Auto aperture — Non-TTL auto — Manual — Repeating flash — Remote i‑TTL i‑TTL — [A : B] Quick wireless flash control —...
Page 857
Supported features Camera modeling illumination Unified flash control — Camera flash unit firmware update — Available during close-up photography only. Not available when RPT is selected as the flash control mode for the remote flash unit. Available only when i‑TTL is selected as the flash control mode for the remote flash unit or when the flash is configured to emit monitor preflashes in mode qA.
Notes on Optional Flash Units Be sure also to consult documentation for the optional flash unit before use. If the unit supports CLS, refer to the section on CLS-compatible digital SLR cameras. This camera is not included in the “digital SLR” category in the documentation for the SB‑80DX, SB‑28DX, and SB‑50DX.
Page 859
Flash Photography Flash photography cannot be combined with some camera features, including: silent mode, video recording, high-speed frame capture, and HDR overlay. Using FV Lock with Optional Flash Units FV lock is available with optional flash units in TTL and (where supported) monitor pre-flash qA and monitor pre-flash A flash control modes (see the documentation provided with the flash unit for more information).
Page 860
Metering Areas for FV Lock The areas metered when FV lock is used with optional flash units are as follows: Stand-Alone Flash control mode Metered area i‑TTL 6-mm circle in center of frame Auto aperture (qA) Area metered by flash exposure meter Remote Flash control mode Metered area...
Page 861
Tip: Modeling Illumination Pressing the control to which [Preview] has been assigned using Custom Setting f2 [Custom controls (shooting)] causes CLS-compatible flash units to emit a modeling flash. This feature can be used with Advanced Wireless Lighting to preview the total lighting effect achieved with multiple flash units.
The EH‑5c and EH‑5b can be used in place of the EH‑5d. MB-N12 Power Battery Pack: A battery pack for the Nikon Z 8 digital camera. When attached, it allows the use of up to two EN‑EL15c rechargeable Li-ion batteries as a power source.
Page 863
● Filters Neutral Color (NC) filters can be used to protect the lens. Filters may cause ghosting when the subject is framed against a bright light, or when a bright light source is in the frame. Filters can be removed if ghosting occurs. Matrix metering may not produce the desired results with filters with exposure factors (filter factors) over 1×...
Page 864
● USB Cables UC-E24 USB Cable: A USB cable with a Type C connector for connection to the camera and a Type A connector for connection to the USB device. UC-E25 USB Cable: A USB cable with two Type C connectors. ●...
Page 865
For information on attaching, removing, maintaining, and using mount adapters, refer to the product documentation. Update to the latest version of the mount adapter firmware if so prompted after attaching the adapter. Information on performing firmware updates is available via the Nikon website for your country or region. ● Microphones ME-1 Stereo Microphone: Connect the ME-1 to the camera microphone jack to record stereo sound.
Page 866
When using a wireless remote controller with the WR-R10, be sure the firmware for the WR-R10 has been updated to the latest version (version 3.0 or later). Information on performing firmware updates is available via the Nikon website for your country or region. Consult a Nikon-authorized service representative when updating the firmware for the WR-R10 from versions prior to version 2.0 to version 3.0 or later.
Page 867
Charging Batteries Compatible batteries can be charged using the devices below. Battery charger EH‑7P charging AC adapter/ Battery EH‑8P AC adapter MH-25a EN‑EL15c EN‑EL15b EN‑EL15a — Attaching and Removing the Accessory Shoe Cover The BS-1 accessory shoe cover slides into the shoe as shown. To remove the cover, hold the camera firmly, press the cover down with a thumb and slide it in the direction shown.
Page 868
The HDMI/USB Cable Clip To prevent accidental disconnection, attach the supplied clip to HDMI or USB cables as shown (note that the clip may not fit all cables). The illustrations show the USB cable. Pass HDMI cables through the other channel. Keep the monitor in the storage position when using the cable clip.
Optional MB-N12 Power Battery Packs Parts of the MB-N12: Names and Functions The name and function of each of the MB-N12’s parts is listed below. Contact cap Protects the MB-N12’s power and signal contacts. Signal contacts — Power contacts — Performs the same role as the multi selector on the camera.
Page 870
Holder-chamber latch See “Inserting Batteries in the MB-N12” ( 875) and “If the Holder-Chamber Cover Detaches” ( 887). Holder-chamber cover 14 15 16 17 Charging connector For use with optional EH‑7P charging AC adapters and EH‑8P AC cover adapters (the latter connected via a UC‑E25 USB cable), which can be used to charge the batteries or power the camera.
Page 871
Battery-chamber cover Holds the camera battery-chamber cover while it is removed from holder the camera. Sub-command dial for Performs the same role as the matching control on the camera. vertical shooting Locks the controls on the MB-N12 to prevent accidental operation. Control lock The control lock is not a power switch.
Page 872
Battery chamber A Holds one EN‑EL15c rechargeable Li-ion battery. Battery power terminals (×2) See “Inserting Batteries in the MB-N12” ( 875). Battery chamber B Holds one EN‑EL15c rechargeable Li-ion battery. Battery holder power terminals See “Inserting Batteries in the MB-N12” ( 875).
Attaching the MB-N12 Before attaching the MB-N12, turn the camera off. To prevent unintended operation while attachment is in progress, leave the control lock on the MB-N12 in the L (locked) position until the process is complete. Remove the contact cap from the battery pack. Keep the contact cap in a safe place.
Page 874
Attach the MB-N12 to the camera. Rotate the attachment wheel in the direction shown by the FLOCK arrow to secure the battery pack in place. Secure the MB-N12 in place by tightening the attachment wheel until it will turn no further. A warning may appear in the camera shooting display if the MB-N12 is not securely attached.
Inserting Batteries in the MB-N12 The MB-N12 can be used with up to two EN‑EL15c rechargeable Li-ion batteries. Before inserting the batteries, turn the camera off. To prevent unintended operation while the batteries are being exchanged, you will also need to leave the control lock on the MB-N12 in the L (locked) position until the exchange is complete.
Page 876
Insert the batteries in the battery holder. Insert the batteries in the orientations shown. The battery latch will click into place when the battery in Chamber A is fully inserted. Insert the battery holder terminals-first. Using the bottom of the battery holder to depress the battery-holder latch, slide the battery holder into the chamber terminals-first.
Page 877
Tip: Removing the Batteries Remove the holder and then remove the batteries as shown. Tip: Exchanging the Battery in Chamber A The battery in Chamber A can be exchanged without removing the battery holder. Insert the battery as shown, stopping when the latch clicks into place. The battery in Chamber A can be removed by pressing the latch as shown and sliding the battery from the holder.
Page 878
Tip: Exchanging Batteries While Shooting When two batteries are inserted, you can replace the battery in Chamber A without turning the camera off. You may find this useful when using the camera continuously for extended periods. Be careful not to press the battery-holder latch and remove the battery holder while exchanging batteries. Tip: Battery Order If you are using only one battery, it can be inserted in either chamber.
Charging Batteries Using an Optional EH‑7P Charging AC Adapter or EH‑8P AC Adapter Batteries inserted in the MB‑N12 can be charged using an optional EH‑7P charging AC adapter or EH‑8P AC adapter. The batteries can be charged even when the MB‑N12 is removed from the camera. Connect an EH‑7P charging AC adapter or EH‑8P AC adapter to the charging connector on the MB‑N12.
Page 880
Plug the EH‑7P or EH‑8P into a household power outlet. EH-7P EH‑8P The batteries charge while the camera is off. They also charge when the standby timer is off. The charge lamp for the battery that is currently charging will light while charging is in progress.
Page 881
Cautions: Charging Batteries The batteries will not charge if the cable is connected to the camera USB Power Delivery connector while the MB‑N12 is attached. Connect the cable to the charging connector on the MB‑N12. The EH‑7P and EH‑8P can be used to charge EN‑EL15c and EN‑EL15b batteries only. They cannot be used to charge EN‑EL15a batteries.
Using an Optional EH‑7P Charging AC Adapter or EH‑8P AC Adapter as a Power Source Optional EH‑7P charging AC adapters and EH‑8P AC adapters can power the camera while connected to the MB‑N12’s charging connector. Cautions: Power Supply Power will be supplied to the camera only if a battery is inserted in one or both of Chambers A and B.
Page 883
Plug the EH‑7P or EH‑8P into a household power outlet. EH-7P EH‑8P The shape of the plug varies with the country or region of purchase. To begin the supply of power to the camera, turn the camera on and select [ON] for [USB power delivery] in the setup menu.
Page 884
Using an Optional EH‑5d AC Adapter and EP‑5B Power Connector The optional EH‑5d AC adapter and EP‑5B power connector provide a steady supply of power when the camera must be left on for extended periods. When using the EH‑5d with the MB-N12, insert the EP‑5B in Chamber A before connecting it to the EH‑5d.
Checking the Level of the Batteries in the MB-N12 When the MB-N12 is connected, the level of the battery currently providing power to the camera is shown in the shooting display and control panel while the camera is on ( 81).
Chamber A. If the camera displays the message [Error. Press shutter-release button to reset.], press the shutter-release button. If the problem persists or recurs frequently, consult a Nikon-authorized service representative.
If the Holder-Chamber Cover Detaches In order to protect the holder-chamber cover from damage, it may detach if force is applied while it is open. The holder-chamber cover can be re-attached as shown. Before re-attaching the holder-chamber cover, slide the cover so that the hinge is visible. Optional MB-N12 Power Battery Packs...
Dimensions (W × H × D) projections Approx. 455 g/1 lb 0.1 oz (with two EN‑EL15c batteries) Weight Approx. 295 g/10.5 oz (without batteries) Nikon reserves the right to change the appearance, specifications, and performance of this product at any time and without prior notice. Optional MB-N12 Power Battery Packs...
Page 889
Low Ambient Temperatures The camera may not function at low temperatures (approximately 10 °C/50 °F or below) when powered by partially-charged batteries. In cold weather, charge one set of batteries before use and keep another in a warm place, ready to be exchanged as necessary. Once warmed, cold batteries may recover some of their charge.
Attaching an EP‑5B Power Connector and EH‑5d, EH‑5c, or EH‑5b AC Adapter Turn the camera off before attaching an EP‑5B power connector and EH‑5d, EH‑5c, or EH‑5b AC adapter. Open the battery chamber (q) and power connector (w) covers. Insert the EP‑5B power connector. Be sure to insert the connector in the correct orientation.
Page 891
Close the battery chamber cover. Position the power connector cable so that it passes through the power connector slot and close the battery chamber cover. Connect the EH‑5d/EH‑5c/EH‑5b AC adapter to the EP‑5B power connector. Connect the power cable to the AC socket on the EH‑5d, EH‑5c, or EH‑5b AC adapter (e). Insert the DC plug from the EH‑5d, EH‑5c, or EH‑5b AC adapter into the DC IN connector (r).
Nikon’s unique NEF/NRW (RAW) format and convert them to JPEG, TIFF, or HEIF (NEF/RAW processing). It supports not only NEF/NRW (RAW) pictures but also JPEG, TIFF, and HEIF photos shot with Nikon digital cameras for such tasks as editing tone curves and enhancing brightness and contrast.
Page 893
Smartphone (tablet) apps are available from the Apple App Store and on Google Play™. For the latest information on our apps, visit the Nikon website. SnapBridge: Download photos and videos from the camera to your smart device via a wireless connection.
Caring for the Camera Long-Term Storage Remove the battery if the product will not be used for an extended period. Before removing the battery, confirm that the camera is off. Do not store the camera in locations that: are poorly ventilated or subject to humidities of over 60%, are next to equipment that produces strong electromagnetic fields, such as televisions or radios, or are exposed to temperatures above 50 °C (122 °F) or below −20 °C (−4 °F).
The image sensor can be cleaned at any time from the menus, or cleaning can be performed automatically when the camera is turned off. If image sensor cleaning fails to resolve the problem, contact a Nikon-authorized service representative. Using the Menus For maximum effect, hold the camera in normal orientation (base down).
Page 896
Cleaning the Image Sensor at Shutdown Option Description The image sensor is automatically cleaned during shutdown each [Clean at shutdown] time the camera is turned off. [Cleaning off] Automatic image sensor cleaning off. Select [Automatic cleaning] for [Clean image sensor]. Pressing 2 when [Automatic cleaning] is highlighted displays [Automatic cleaning] options.
If foreign matter cannot be removed from the image sensor using image sensor cleaning, the sensor can be cleaned manually as described below. Note, however, that the sensor is extremely delicate and easily damaged; we recommend that manual cleaning be performed only by a Nikon-authorized service representative.
Page 898
Servicing the Camera and Accessories The camera is a precision device and requires regular servicing; Nikon recommends that the camera be inspected once every one to two years, and that it be serviced once every three to five years (note that fees apply to these services).
Caring for the Camera and Battery: Cautions Cautions: Using the Camera ● Do Not Drop Do not drop the camera or lens or subject them to blows. The product may malfunction if subjected to strong shocks or vibration. ● Keep Dry Keep the camera dry.
Page 900
● Lasers and Other Bright Light Sources Do not direct lasers or other extremely bright light sources toward the lens, as this could damage the camera’s image sensor. ● Cleaning When cleaning the camera body, use a blower to gently remove dust and lint, then wipe gently with a soft, dry cloth.
Page 901
● Do Not Touch the Sensor Shield If [Sensor shield closes] is selected for [Sensor shield behavior at power off] in the setup menu, the sensor shield in front of the image sensor will close when the camera turns off. Never pierce or apply pressure to the sensor shield.
Page 902
● Monitor/Viewfinder The monitor and viewfinder are constructed with extremely high precision; at least 99.99% of pixels are effective, with no more than 0.01% being missing or defective. Hence while these displays may contain pixels that are always lit (white, red, blue, or green) or always off (black), this is not a malfunction.
Cautions: Using Batteries ● Precautions for Use If improperly handled, batteries may rupture or leak, causing the product to corrode. Observe the following precautions when handling batteries: Turn the product off before replacing the battery. Batteries may be hot after extended use. Keep the battery terminals clean.
Page 904
● Charge Batteries Before Use Charge the battery before use. The supplied battery is not fully charged at shipment. ● Ready Spare Batteries Before taking photographs, ready a spare battery and keep it fully charged. Depending on your location, it may be difficult to purchase replacement batteries on short notice. ●...
Cautions: Using the Charger Do not move the charger or touch the battery during charging; failure to observe this precaution could in very rare instances result in the charger showing that charging is complete when the battery is only partially charged. Remove and reinsert the battery to begin charging again. Do not short the charger terminals.
Specifications Nikon Z 8 Digital Camera Type Type Digital camera with support for interchangeable lenses Lens mount Nikon Z mount Lens Z mount NIKKOR lenses Compatible lenses F mount NIKKOR lenses (mount adapter required; restrictions may apply) Effective pixels Effective pixels 45.7 million...
Page 907
Storage [FX (36 × 24)] selected for image area: 8256 × 5504 (Large: 45.4 M) 6192 × 4128 (Medium: 25.6 M) 4128 × 2752 (Small: 11.4 M) [DX (24 × 16)] selected for image area: 5392 × 3592 (Large: 19.4 M) 4032 × 2688 (Medium: 10.8 M) 2688 × 1792 (Small: 4.8 M) Image size (pixels) [1:1 (24 ×...
Page 908
Storage Auto, Standard, Neutral, Vivid, Monochrome, Portrait, Landscape, Flat, Creative Picture Controls (Dream, Morning, Pop, Sunday, Somber, Dramatic, Silence, Bleached, Melancholic, Pure, Denim, Toy, Sepia, Blue, Red, Pink, Charcoal, Graphite, Binary, Carbon); Picture Control System selected Picture Control can be modified; storage for custom Picture Controls Note: Choice of Picture Controls is restricted to Standard, Monochrome, and Flat when HLG is selected for tone mode during...
Page 909
Monitor 8-cm/3.2-in., approx. 2100k-dot vertically and horizontally tilting TFT touch-sensitive LCD with 170° viewing angle, approximately Monitor 100% frame coverage, and color balance and 15-level manual brightness controls Shutter Type Electronic shutter with shutter sound and sensor shield ¹⁄₃₂₀₀₀ – 30 s (choose from step sizes of ¹⁄₃, ¹⁄₂, and 1 EV, extendable Speed to 900 s in mode M), bulb, time Flash synchronizes with shutter at speeds of ¹⁄₂₅₀...
Page 910
Exposure Metering system TTL metering using camera image sensor Matrix metering Center-weighted metering: Weight of 75% given to 12 or 8 mm circle in center of frame or weighting can be based on Metering mode average of entire frame Spot metering: Meters circle with a diameter of approximately 4 mm centered on selected focus point Highlight-weighted metering −3 – +17 EV...
Page 911
Autofocus Type Hybrid phase-detection/contrast AF with AF assist −7 – +19 EV (−9 – +19 EV with starlight view) Measured in photo mode at ISO 100 and a temperature of Detection range 20 °C/68 °F using single-servo AF (AF‑S) and a lens with a maximum aperture of f/1.2 Autofocus (AF): Single-servo AF (AF‑S);...
Page 912
Accessory shoe ISO 518 hot-shoe with sync and data contacts and safety lock i-TTL flash control, radio-controlled Advanced Wireless Lighting, Nikon Creative Lighting optical Advanced Wireless Lighting, modeling illumination, FV System (CLS) lock, Color Information Communication, auto FP high-speed sync,...
Page 913
Video Metering system TTL metering using camera image sensor Metering mode Matrix, center-weighted, or highlight-weighted 7680 × 4320 (8K UHD): 30p (progressive)/25p/24p 3840 × 2160 (4K UHD): 120p/100p/60p/50p/30p/25p/24p Frame size (pixels) and 1920 × 1080: 120p/100p/60p/50p/30p/25p/24p frame rate Note: Actual frame rates for 120p, 100p, 60p, 50p, 30p, 25p, and 24p are 119.88, 100, 59.94, 50, 29.97, 25, and 23.976 fps respectively.
Page 914
Video Active D‑Lighting Extra high, High, Normal, Low, and Off Time-lapse video recording, electronic vibration reduction, time codes, N-Log and HDR (HLG) video, wave-form display, red REC frame indicator, video recording display zoom (50%, 100%, and Other options 200%), extended shutter speeds (mode M), and dual-format (proxy- video) recording for RAW video;...
Page 915
Wi-Fi/Bluetooth Standards: IEEE 802.11b/g/n (Africa, the Middle East (other than Israel), Taiwan, Bangladesh, Pakistan, and Bolivia) IEEE 802.11b/g/n/a/ac (other countries in the Asia, Europe, Israel, Australia, New Zealand, the Republic of Fiji, U.S.A., Canada, and Mexico) IEEE 802.11b/g/n/a (other countries in the Americas) Operating frequency: Europe (excluding the countries listed below), Israel, and Turkey: 2412–2472 MHz (channel 13) and 5180–5825 MHz...
Page 916
Wi-Fi/Bluetooth Communication protocols: Bluetooth Specification version 5.0 Operating frequency: Bluetooth: 2402–2480 MHz Bluetooth Bluetooth Low Energy: 2402–2480 MHz Maximum output power (EIRP): Bluetooth: −4.1 dBm Bluetooth Low Energy: −5.6 dBm Power source * One EN‑EL15c rechargeable Li-ion battery EN‑EL15b and EN‑EL15a batteries can be used in place of the EN‑EL15c.
Page 917
Nikon reserves the right to change the appearance and specifications of the hardware and software described in this document at any time and without prior notice. Nikon will not be held liable for damages that may result from any mistakes that this document may contain.
Page 918
MH‑25a Battery Charger Rated input AC 100 to 240 V, 50/60 Hz, 0.23–0.12 A Charging output DC 8.4 V/1.2 A Supported batteries EN‑EL15c, EN‑EL15b, and EN‑EL15a rechargeable Li-ion batteries Approx. 2 hours and 35 minutes Charging time Time required to charge battery at an ambient temperature of 25 °C (77 °F) when no charge remains Operating temperature 0°C–...
Page 919
Type Rechargeable lithium-ion battery Rated capacity 7.0 V, 2280 mAh Operating temperature −10 °C–40 °C (+14 °F–104 °F) with Z 8 Dimensions (W × H × D) Approx. 40 × 56 × 20.5 mm/1.6 × 2.3 × 0.9 in. Weight Approx. 80 g (2.9 oz), excluding terminal cover Cautions: Disposing of Data Storage Devices Please note that deleting pictures or formatting memory cards or other data storage devices does not completely erase the original image data.
Slower speeds may result in recording or playback being interrupted. Nikon 660 GB MC‑CF660G Type B CFexpress memory cards or ProGrade Digital COBALT-series CFexpress memory cards are recommended, particularly when [N‑RAW 12-bit (NEV)] or [ProRes RAW HQ 12-bit (MOV)] is selected for [Video file type]...
Portable Chargers (Power Banks) Portable chargers can be used to power the camera or charge the camera battery. The following table lists the portable chargers that have been tested and approved for use, together with the approximate number of shots that can be taken with, and the approximate number of times the camera battery can be charged using, each device.
Memory Card Capacity The following table shows buffer capacity and the approximate number of pictures that can be 1 stored on a 660 GB card at different image qualities ( 101), and sizes ( 103) with [FX (36 × 24)] selected for [Choose image area] and [SDR] selected for [Tone mode]. Actual capacity varies with shooting conditions and the type of card.
Page 923
251,000 frames 1.8 MB Figures are for a Nikon 660 GB MC‑CF660G Type B CFexpress memory card (as of March 2023) with a NIKKOR Z 50mm f/1.8 S lens mounted on the camera. The number of pictures that can be saved to the memory card or stored in the memory buffer varies with the scene recorded.
Memory Card Capacity (Videos) 1 The following table shows the approximate length of footage that can be stored on a 660 GB card with different options selected for [Frame size/frame rate] ( 193) in the video recording menu when [H.265 8-bit (MOV)] is selected for [Video file type]. Each shot can be up to 125 minutes in length.
Page 925
Frame size/frame rate Maximum capacity [1920×1080; 30p] [1920×1080; 25p] Approx. 1859 minutes [1920×1080; 24p] Figures are for a Nikon 660 GB MC‑CF660G Type B CFexpress memory card (as of March 2023). Memory Card Capacity (Videos)
Battery Endurance The video footage or number of shots that can be recorded with a fully-charged EN‑EL15c 1 rechargeable Li-ion battery is given below. Actual endurance varies with such factors as the condition of the battery, the interval between shots, and the options selected in the camera menus. 3 Photo Mode (Single Frame): Number of Shots [Viewfinder only] selected for monitor mode with:...
Page 927
To ensure that you get the most from rechargeable Nikon EN‑EL15c batteries: Keep the battery contacts clean. Soiled contacts can reduce battery performance. Use batteries immediately after charging. Batteries will lose their charge if left unused. EN‑EL15b and EN‑EL15a batteries can be used in place of the EN‑EL15c. Note, however, that fewer pictures can be taken on a single charge than with the EN‑EL15c.
All other trade names mentioned in this document or the other documentation provided with your Nikon product are trademarks or registered trademarks of their respective holders. Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple products identified in the badge, and has been certified by the developer to meet Apple performance standards.
Page 930
FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE https://www.mpegla.com BSD License (NVM Express Driver) The license for the open-source software included in the camera’s NVM Express driver is as follows: https://imaging.nikon.com/support/pdf/LicenseNVMe.pdf Other Open-Source Software Additional open-source licenses can be found at the URL below: https://imaging.nikon.com/oss/en/index.htm...
Notices ● Notices for Customers in the U.S.A. The Battery Charger IMPORTANT SAFETY INSTRUCTIONS—SAVE THESE INSTRUCTIONS DANGER—TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet if needed.
Page 932
CAUTIONS Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment. Interface Cables Use the interface cables sold or provided by Nikon for your equipment.
Page 933
● Notices for Customers in Europe CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. This symbol indicates that electrical and electronic equipment is to be collected separately. The following apply only to users in European countries: This product is designated for separate collection at an appropriate collection point.
FCC WARNING The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Nikon Corporation may void the user’s authority to operate the equipment. Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip.
Page 935
Co-location This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Nikon Inc., 1300 Walt Whitman Road, Melville, New York 11747-3064, U.S.A. Tel.: 631-547-4200 FCC/ISED RF Exposure Statement The available scientific evidence does not show that any health problems are associated with using low power wireless devices.
Page 936
Compliance with RSS-247 Issue 2 §6.4 Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet.
Page 937
● Notice for Customers in Europe and in Countries Complying with the Radio Equipment Directive Hereby, Nikon Corporation declares that the radio equipment type Z 8 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://imaging.nikon.com/support/pdf/DoC_N2120.pdf...
Page 938
Less than 2 W ● Notice for Customers in the UK Hereby, Nikon Corporation declares that the radio equipment type Z 8 is in compliance with Radio Equipment Regulations 2017. The full text of the UKCA declaration of conformity is available at the following internet address: https://imaging.nikon.com/support/pdf/UKCA_DoC_N2120.pdf...
Page 939
Unsecured networks: Connecting to open networks may result in unauthorized access. Use secure networks only. Tip: Conformity Marking The standards with which the camera complies can be viewed using the [Conformity marking] option in the setup menu. Z 8 Model Name: N2120 Bluetooth and Wi-Fi (Wireless LAN)
Index Index 16:9 (36×20) (Image area) ( 100) Symbols, Numerics 3D-tracking ( 107) P (Programmed auto) ( 122) S (Shutter-priority auto) ( 122) A (Aperture-priority auto) ( 122) M (Manual) ( 123) U (Single frame) ( 133) AC adapter ( 890) V (Continuous low-speed) ( 133)
Page 941
Attenuator ( 542) C60 ( 136, 588) Auto (Set Picture Control) ( 175) Camera control ( 365) Auto (White balance) ( 143) Camera Control Pro 2 ( 365) Auto bracketing ( 162) Camera sounds ( 742) Auto bracketing (mode M) ( 617) Candidates for deletion ( 246)
Page 945
Perspective control ( 270) Photo flicker reduction ( 457) Photo information ( 214) Rating ( 237) Photo shooting menu ( 418) RAW primary - HEIF secondary (Secondary slot Photo/video selector ( function) ( 429) Picture review ( 698) RAW primary - JPEG secondary (Secondary slot Pictures shot on selected dates ( 246) function) (...
Page 946
Sensor shield behavior at power off ( 728) Series playback ( 697) Set Picture Control ( 175) Thumbnail playback ( 212) Set Picture Control (HLG) ( 442) Time ( 126) Set the clock ( Time (Long time-exposures) ( 126) Setup menu ( 707) Time zone and date ( 713)
Page 948
No reproduction in any form of this document, in whole or in part (except for brief quotation in critical articles or reviews), may be made without written authorization from NIKON CORPORATION. SB3E02(11) 6MO05211-02...