Operation; Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL TC-AV 1200 Original Operating Instructions

5.1 Assembling the appliance
Fitting the appliance head (Fig. 2-5)
The appliance head (3) is fastened to the con-
tainer (7) by the locking hook (6). To remove the
appliance head (3), open the locking hook (6) and
remove the appliance head (3). When fi tting the
appliance head (3), make sure that the locking
hook (6) locks into place correctly.
Plug the vacuum tube (9) onto the end of the suc-
tion hose (10).
Fit the suction hose (10) onto the connection (8)
and turn until securely attached.
Fitting the handle (Fig. 10)
Use a screwdriver to fi t the handle (1).
5.2 Fitting the fi lter
Notice!
Never use the ash vacuum without the fi lter!
Always ensure that the fi lters are perfectly secure.
Dismantling/Assembly of the fi lter (Fig. 6-8)
Turn the fi lter cage (4) to the left and remove it
from the appliance head (3). Next, remove the
fi lter cartridge for fi ne ash dust (11). Now remove
the foam fi lter (12).
Important!
If no fi lter cartridge for fi ne ash dust (11) is fi tted
to the equipment head (3), it will be impossible to
switch on the ash vacuum cleaner. The equipment
comes with two switches (z) which allow operati-
on only when they are pressed and when a fi lter
cartridge is fi tted (Fig. 9).

6. Operation

6.1 ON/OFF switch (Fig. 1/2)
Press the ON/OFF switch (2) to switch the equip-
ment ON and OFF.
6.2 Blowing
Connect the suction hose (10) to the blow con-
nector (5) of the ash vacuum cleaner.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
Anl_TC_AV_1200_SPK7.indb 17 Anl_TC_AV_1200_SPK7.indb 17
GB
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible.
•
We recommend that you clean the appliance
immediately after you use it.
8.2 Cleaning the appliance head (3)
Clean the appliance regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plas-
tic parts in the appliance.
8.3 Cleaning the container (7)
The container can be cleaned with a damp cloth
and some soft soap or under running water, de-
pending on the amount of dirt.
8.4 Cleaning the fi lter (Fig. 6-8)
The foam fi lter (12) can be cleaned with soft soap
and running water and dried in the air. Clean the
fi lter basket (4) and the fi lter cartridge (11), e.g.
by tapping and brushing or by blowing out with
compressed air at low pressure.
8.5 Servicing
At regular intervals and before each use, check
that the fi lters in the ash vacuum are securely
fi tted.
8.6 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
- 17 -
30.01.2017 10:46:58 30.01.2017 10:46:58