Thales payShield 10K PS10-D Quick Start Manual

9.Connect using the console
The console terminal is pre-conFlgured to communicate with the HSM via the USB-C to USB-A cable.
• Use the supplied USB-C to USB-A cable to connect the USB-C port on the front of the payShield l OK to your laptop
NOTE: if laptop USB-A port, you will need to order
your has a USB-C port, instead of a
• For Windows, ensure that all Windows updates have been applied and the laptop is connected to the internet before connecting to the
payShield. Upon connection, Windows will detect the new hardware and install the drivel The device will appear as a new COM port.
• If the laptop cannot be connected to the internet, the drivers are available for download and manual installation from the Microsoft Update
Catalog: www.catalog.update.microsoft.com/Search.aspx?q = Pl%20USB%20to%20serial
S, Sear�h results for "Pl USB to serial"
• Download the CAB Flle for the laptop operating system and extract the Flies into a folder
• Expand the "Other devices" section of the Device Manager and look for "Gadget Serial v2.4". Right click on that and select the option to
install the drivel Choose the option to browse for the driver and select the folder from the previous step.
• You may need to be signed in with an administrator account to install drivers
• Using a standard terminal emulation program, select the set up for serial terminal emulation and configure it as follows:
• Baud Rate: 9600 bps
• Word Length: 8 bits
• Parity: None
• Stop Bits: l bit
Test the connection:
• Press the <Return> key on the console/laptop keyboard
The HSM should respond by displaying "Online>", "OIFline>", or "Secure>" based on the position of the keys.
The appearance of this prompt indicates that the correct communications between the console and the HSM have been established, but that
no command has been entered.
10. Connect cables for payShield Manager
payShield Manager provides a secure GUI interlace with an authenticated, encrypted connection allowing a full remote or local management
of the payShield l OK.
Remote payShield Manager requires an Ethernet cable from the Management Port into your network.
If you are not using DHCP, then you may need to use the console to set up the static IP address far payShield Managel
(See the payShield 10K Manager Quick Start Guide.)
11. Configure payShield Manager
• Follow the instructions provided in the payShield Manager Quick Start Guide to complete the conFlguration of payShield Manager
12. Configuring the host ports
Depending upon the conFlguration connection required between the Host and the payShield l OK, you may require additional information from
your Network or Systems Support Group in order to complete this step.
• Using either the console or payShield Manager, conFlgure the Host ports to suit your system requirements
The parameters you need to enter will vary, depending upon the type of communications to be used.
Test the connection:
• The way in which you do this will vary, depending upon your system conFlguration; for example: Ethernet environment - issue a PING
command (both from the payShield l OK to the Host, and from the Host to the payShield l OK)
> cpl.thalesgroup.com <
Contact us - For all office locations and contact information, please visit
standard to cable.
or provide a USB-C USB-C
cpl.thalesgroup.com/ contact-us
payShield lOK PSlO-D
Installation Quick Start Guide
007-700236-001 Rev C
Device Overview
Left key lock Health LED
10Gb 10Gb Manage­ Serial number Service LED
Ethernet ment & Auxiliary
Printer ports
Ethernet ports
ports 1 & 2
(Ethernet &
USBA)
Erase LED
Ground lug
User Documentation
The payShield l OK user manuals are available for download from the Thales CPL support website:
https:/ supportportal. thalesgroup.com/ csm
/
1. Assure Safety
• Before installing, and using this product, please read the Warnings and Cautions in the following document:
payShield l OK Regulatory User Warnings & Cautions
2. Unpack
Remove from packaging:
• Remove the Accessories box
0
"'
• Remove the payShield l0K from the packaging, checking that the tamper evident bag containing the unit is not tampered
>
Cl
• Check that the serial number on the tamper evident bag matches that supplied by email or shipment confirmation by Thales
Remove the accessories from the Accessories box.
Verify the contents:
8
• payShield lOK PS 10-D Host Security Module
-6 • HSM Rail Kit
('")
R
N • 2 AC power cables
• 4 Security keys in tamper evident bags (2 copies - 4 total keys)
�
Carry out the following checks:
• Check that the tamper evident bag containing the keys is not tampered and the serial number matches that supplied by email or shipment confirmation by Thales
• Locate the serial number on the key tag and verify that it matches the serial number on the unit
N
0
N
2 cables 4 security keys
0
N
0.
C,
f2
(')
al
0
_.J::
f-
THALES
Tamper light
Service light with serial number
Service light Right key lock
Smart card reader
USB-C
on/ off button
console port
2x Hot swappable power supplies
2x Hot swappable fans
Erase button
access
Power switch
• USB-C to USB-A cable (for console connectivity)
• payShield lOK Regulatory User Warnings & Cautions document
• payShield lOK PS 10-D Installation Quick Start Guide (this document)
• payShield Manager Quick Start Guide
• 4 SFP Transceivers, either Optical or Copper (ordered separately)
4 transeivers USB-C to USB-A cable
we can all trust