Related Manuals for Autotrol Performa Ultra
Summary of Contents for Autotrol Performa Ultra
- Page 1 ® ™ Autotrol Performa Ultra Electronic Control System Operation and Maintenance Manual...
-
Page 2: Table Of Contents
Table of Contents Performa Ultra ......3 Electronic Demand System ....3... -
Page 3: Performa Ultra
Low or No Water Usage conventional conditioner operating on a fixed The Performa Ultra is programmed to recognize a day regeneration schedule. of very little or no water usage as an abnormality. It will... -
Page 4: Injector Selection
Guest Cycle Manual time cycles: • An extra regeneration can be achieved at any time by Refill...5 minutes pressing the INDICATOR KNOB. It will take a few • Brine and Rinse...2 hours minutes for the regeneration to start and the unit will •... -
Page 5: Riser Pipe Assembly
Table 2 - Injector Selection Resin Tank Diameter, inches (cm) Water Pessure psi, (bar) 7 (18) 8 (21) 9 (23) 10 (25) 12 (30) 20 to 60 (1.38 to 4.14) 61 to 120 (4.20 to 8.27) Table 3 - Injector Flow Rates Brine Draw Rate Rinse Rate Injector P/N (“Bumps”) -
Page 6: Installation
Installation Not in Bypass In Bypass • All plumbing and electrical connections must conform to local codes. • Inspect unit carefully for carrier shortage or shipping damage. Location Selection 1. The distance between the unit and a drain should be as short as possible. -
Page 7: Brine Line Connection
(in the brine tank) and the tube fitting on itself. the valve. Programming the Performa Ultra Electrical Connection 1. Plug the wall mount transformer into a functioning Plug the wall mount transformer into a wall outlet that electrical outlet that is not controlled by a switch. -
Page 8: Calendar Override
2. Remove the access door by flexing the removal tab 6. Place the jumper on the pins marked LBS of SALT to the left (as facing the control) then gently pulling (Figure 8). Press the black TIME SET button until the tab and door out and off the control (Figure 4). - Page 9 Table 4 - Salt and Capacity Settings * Salt System System System System System System System Setting 2 & 3 4 & 5 (lbs.) 6,000 8,000 8,000 8,000 9,000 10,000 11,000 10,000 11,000 12,000 14,000 15,000 16,000 10,000 13,000 13,000 16,000 17,000 18,000...
-
Page 10: Changing The System Number
Changing the System Number Removing 463i for Servicing 1. Unplug the power cord. 1. Place one jumper on HARDNESS and one on LBS of SALT. 2. Remove cover. 2. Press TIME SET Button (Figure 4) until desired 3. Align the indicator arrow on the rear of the system number (Table 1) is displayed. - Page 11 Preventive Maintenance IMPORTANT: Do not overtigtten the plastic cap. Seat the cap lightly into position. Overtightening may cause Injector Screen and Injector breakage of the plastic cap that may not be immediately evident. Inspect and clean brine tank and screen filter on end of brine pickup tube once a year or when sediment 11.
-
Page 12: Specifications
Specifications Inlet 2.5 inch (63 mm) Drain 2.5 inch (63 mm) Outlet 11.59 inch (294 mm) 2.88 inch (73 mm) 1.356 inch (34 mm) 3.37-inch (86 mm) 3.66-inch (93 mm) 5.76 inch (146 mm) 5.82 inch (148 mm) Hydrostatic Test Pressure ............300 psi (20.69 bar) Working Pressure. -
Page 13: Flow Diagrams
Flow Diagrams 2 Refill Position 1 Service Position Brine Brine Adjustment Adjustment Brine Tank Brine Tank Inlet Inlet Outlet Outlet Drain Drain Valve Name Brine 1 - Closed Valve By-Pass 2 - Closed Name 3 - Open Inlet Brine 1 - Open Outlet 4 - Open By-Pass... - Page 14 Brine 5 Purge Position Brine 4 Backwash Position Adjustment Adjustment Brine Tank Brine Tank Inlet Inlet Outlet Outlet Drain Drain Valve Name 1 - Closed Brine Valve By-Pass 2 - Open Name 3 - Closed Inlet Brine 1 - Closed Outlet 4 - Open By-Pass...
-
Page 15: Replacement Parts
Replacement Parts Valve System Assembly... - Page 16 Parts List Part Part Code Description Qty. Code Description Qty. 1035610 Valve Assembly, w/o Flow Controls Brine Refill Control: 1035626 Camshaft: Tan 1000222 0.33 gpm Flow Control 1031391 Timer Locking Pin 1000226 Screen/Cap Assembly Drain Control Assembly: 1010429 O-Ring 1000209 No.
- Page 17 463i Control 1265 Bypass Part Code Description Qty. 1030070 463i Control 1040930 1265 Bypass 1000811 Transformer 1000907 Transformer Extension Cord 15 feet (4.6 m) 1034264 Y-Splitter (run 2 units from 1 transformer) *Not Shown...
-
Page 18: Bypass Valve
Troubleshooting IMPORTANT: Service procedures that require the water pressure to be removed from the system are Your water conditioning system is designed and marked with a ! after the possible cause. To remove manufactured for efficient, low maintenance service. water pressure from the system, put the bypass valve However, if problems occur, this section provides a list or three-valve bypass into the bypass position and of possible causes and solutions. - Page 19 10. Valve will not draw brine. Low water pressure. Make correct setting according to instructions. b. Restricted drain line. b. Remove restriction. Injector plugged Clean injector and screen. d. Injector defective d. Replace injector and cap. Valve (2 and/or 3) not closed. Flush out foreign matter holding disc(s) open by manually operating valve stem(s).
-
Page 20: Disinfection Of Water Conditioners
Disinfection of Water Conditioners Calcium Hypochlorite Calcium hypochlorite, 70% available chlorine, is The construction materials of the Water Conditioning available in several forms including tablets and System do not support bacterial growth or contaminate granules. These solid materials can be used directly the water supply. - Page 21 © Copyright 2000 Osmonics Printed in USA P/N 1224525 Rev. A...