Related Manuals for Philips FlexTune
Summary of Contents for Philips FlexTune
- Page 1 Tunable White Systems FlexTune Quick Installation Guide FlexTune Quick Installation Guide June 2021...
-
Page 2: Table Of Contents
Content Introduction The FlexTune Building Blocks How to build a wireless TW-System How to build a wired TW-System How to build a TW-System with Touch & Dim Where to find more in-detail information Disclaimer < >... -
Page 3: Introduction
Introduction Philips FlexTune offers a complete, easy-to-install, and future-proof Tunable White System. This Quick Installation Guide explains the basics and helps you to get up-and-running. For full explanation, several in-detail technical documents can be downloaded from our website (see page 11) <... -
Page 4: The Flextune Building Blocks
2. A Tunable White (TW) module, for instance a Philips Fortimo FlexTune module 3. A TW control system, complying to the DALI 209 Standard. a. Wireless: A TW-compatible node in combination with commissioning app (e.g. Philips EasyAir SNS210 MC and the Philips field app MC) and a compatible wireless switch b. -
Page 5: How To Build A Wireless Tw-System
3. Install the commissioning app, e.g. Philips field app MC. 4. Switch on the system and start the app. 5. Commission the switch (and other components you want to add) with the app. 6. Optionally: Use the app to create Zones and Scenes according to your wishes... - Page 6 Basics of a Wireless TW-System Xitanium FlexTune Driver Node Fortimo FlexTune Module 2-wire driver to node 4-wire driver to module 4-wire driver to module connection connection connection Wireless Switch Cell Phone with MasterConnect app...
-
Page 7: How To Build A Wired Tw-System
Connect the DALI 209 control module to the driver, this is a two-wire connection to the SR-pins of the driver. The plus connection of the control module must be connected to the SR+ pin of the driver. Please note: DALI 207 Controls with dual addessing mode are not supported by the FlexTune drivers. module... - Page 8 Basics of a Wired TW-System Xitanium FlexTune Driver Fortimo FlexTune Module 2-wire driver to control module connection 4-wire driver to module connection Dali 209 compatible Control Module...
-
Page 9: How To Build A Tw-System With Touch & Dim
How to build a TW-System with Touch & Dim 1. Configure the driver Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements. More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11. - Page 10 Basics of a T&D TW-System Xitanium FlexTune Driver Fortimo FlexTune Module 4-wire driver to module connection Double push button...
-
Page 11: Where To Find More In-Detail Information
4. Nodes: Design-in Guide EasyAir SNS210 MC 5. App: Installer Manual Philips field app MC Philips MC control app for end users 6. Switches: List of Supported Switches Manuals for switch commissioning: Connected Lighting Solutions > Apps and Accessories > Wireless Switches... -
Page 12: Disclaimer
Disclaimer ©2021 Signify Holding B.V. All rights reserved. Note that the information provided in this document is subject to change. This document is not an official testing certificate and cannot be used or construed as a document authorizing or otherwise supporting an official release of a luminaire. - Page 13 Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.