Table of Contents
Advertisement
Quick Links
Use the Wireless TROLL Com to connect an In-Situ instrument to a Bluetooth-enabled mobile
device and the VuSitu mobile app. The Wireless TROLL Com doesn't have internal data storage.
It allows data transfer between an instrument and VuSitu (or Win-Situ 5 via a USB cable).
1
6
Connection status indicator
Flashing red = The Wireless
TROLL Com, instrument, and
Bluetooth-enabled device are
not connected.
Continuous red = The Wireless
TROLL Com is connected to an
instrument, but not connected
to a Bluetooth-enabled mobile
device.
Flashing green = The Wireless
TROLL Com is connected to the
Bluetooth-enabled device, but is
not connected to an instrument.
Continuous green = The
Wireless TROLL Com, instrument,
and Bluetooth-enabled device
are connected.
5
Cable connector
Attach an instrument to the Wireless TROLL Com with a Rugged Cable
before connecting to VuSitu. When switching instruments, you may need to
turn the Wireless TROLL Com off and on again.
Information subject to change without notice. In-Situ, In-Situ logo, "Water Simplified", VuLink, RDO, RuggedCable, TROLL,
BaroTROLL, HydroVu, VuSitu, Baro Merge, and Win-Situ are trademarks or registered trademarks of In-Situ Inc. ©2023. All
rights reserved. This product may be covered by patents identified at www.in-situ.com/patents
USB connection
Plug your Wireless TROLL Com
into a PC for charging or setup.
Wireless TROLL Com/Wireless Rugged TROLL Com
2
Wireless Rugged
TROLL Com
Dust cover for USB connection
3
On/Off button
Press the button once to turn
the device on or off.
4
Battery charge status
indicator
2023-03-20 | 0031242
100% - 90%
90% - 75%
75% - 50%
50% - 25%
Less than 25%
Advertisement
Table of Contents
Related Manuals for In-situ Wireless TROLL Com
Summary of Contents for In-situ Wireless TROLL Com
- Page 1 Wireless TROLL Com off and on again. Information subject to change without notice. In-Situ, In-Situ logo, “Water Simplified”, VuLink, RDO, RuggedCable, TROLL, BaroTROLL, HydroVu, VuSitu, Baro Merge, and Win-Situ are trademarks or registered trademarks of In-Situ Inc. ©2023. All 2023-03-20 | 0031242...
- Page 2 A fully-charged communication device will run for up to 40-50 continuous hours. Avoid full discharges and charge the battery each use. Do not store the Wireless TROLL Com in temperatures above 122 F/50 C. Connecting to VuSitu with a Wireless TROLL Com You must have the VuSitu mobile app to use the instrument with a mobile device.
- Page 3 Communications radio firmware. button and then choose the correct Com Port. Click check mark button. Default communication settings The following default communication settings are most common for In-Situ instruments: • Baud: 19200 • Data bits: 8 • Parity bits: Even •...
- Page 4 Rebooting the Wireless TROLL Com Follow the steps below if your Wireless TROLL Com doesn’t respond while connected to a computer. Disconnect the Wireless Turn on the Wireless Hold the Power button Turn the Wireless TROLL TROLL Com from a TROLL Com.
- Page 5 In-Situ Technical Support for assistance. • Do not use the Wireless TROLL Com in any manner not specified by the manufacturer. If the device is used in a manner not specified in this manual, the protection provided by the equipment may be impaired.
Need help?
Do you have a question about the Wireless TROLL Com and is the answer not in the manual?
Questions and answers