Table of Contents
Advertisement
Original instructions
1. Declaration of Conformity
Under our sole responsibility, we hereby declare
that these compressed air stapler guns, identified
by type and serial number *1), meet all relevant
requirements of directives *2) and standards *3).
Technical documents for *4) - see Page 3.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 3,
hereby declare under sole responsibility that these
compressed air stapler guns, identified by type and
serial number *1) on page 3, fulfill all relevant
provisions of following UK Regulations S.I. 2008/
1597 and Designated Standards EN ISO
12100:2010, EN 792-13:2000+A1:2008
2. Specified Use
DKG 80/16 are designed for driving in staples in the
professional sector.
DKNG 40/50 is designed for driving in staples and
finishing nails in the professional sector.
DSN 50 is designed for driving in finishing nails in
the professional sector.
The tool is not suited for driving in staples into hard
surfaces such as steel and concrete!
The stapler and fasteners should be regarded as a
technical safety system. Only use the fasteners
named in these operating instructions for the
respective tool (see Section 11. Technical Specifi-
cations).
This air tool must only be operated with a com-
pressed air supply. Do not operate with explosive,
combustible or harmful gases, or with oxygen. The
maximum supply pressure specified on the air tool
must never be exceeded. It must not be used as a
lever, crushing tool or striking tool.
Any other use does not comply with the intended
purpose. Unspecified use, modification of the air
tool or use of parts that have not been tested and
approved by the manufacturer can cause unfore-
seeable damage.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.
3. General Safety Instructions
For your own protection and for the
protection of your air tool, carefully
observe all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety warn-
ings and instructions may result in electric shock,
fire and/or serious injury.
Warning: Please read the
instructions and warnings for this
tool carefully before use. Failure to
do so could lead to serious injury.
Keep all safety instructions and information for
future reference.
Pass on your air tool only together with these docu-
ments.
- The user or user's employer must evaluate the
specific risks associated with each application of
the tool.
- You must read and understand the safety instruc-
tions before installing, operating, repairing or
maintaining the tool, and also before replacing any
fasteners or carrying out any work in the vicinity of
the air tool. Failure to read and follow the instruc-
tions may lead to serious injury.
- Only qualified, trained operators are authorised to
install, adjust or use the air tool.
- The air tool must not be modified. Any modifica-
tions implemented may reduce the efficiency of
the safety measures and increase risks for the
operator.
- Never use air tools that have been damaged. Look
after your air tools carefully. Regularly check that
all moving parts are functioning correctly without
jamming. Also regularly ensure that no parts are
broken or damaged to an extent that they affect
the operation of the air tool. Check that all signs
and labels are legible and intelligible. Have
damaged parts repaired or replaced before using
the tool. Many accidents are caused by poorly
maintained air tools.
- Keep your fingers away from the trigger if you do
not use this tool and change from one working
position to another.
- Be careful when handling staples, especially
when loading and unloading, as staples have
sharp tips that could cause injury.
- Only wear gloves that provide a suitable feel and
safe operation of the shutter release and all
adjustment devices.
4. Special Safety Instructions
4.1
Risks associated with ejected parts
- If either the workpiece, fasteners or the air tool
breaks, parts may be ejected at high speed.
- During operation, when replacing accessories or
fasteners or during repair and maintenance work
on the air tool, you must always wear impact-
resistant safety goggles. The degree of protection
required for each individual task must be evalu-
ated separately in each case.
- Ensure that the workpiece is securely attached.
ENGLISH en
11
Advertisement
Table of Contents
