HORI Racing Wheel Overdrive for Xbox One Manual

Before using this product please read the instructions carefully.

After reading the instruction manual, please keep it for reference.

Caution

Parents/Guardians: Please read the following information carefully.

• This product contains small parts. Keep away from children under 3 years old.
• Keep this product away from small children or infants. Seek medical attention immediately if any small parts are swallowed.
• Long cord. Strangulation hazard.
• Keep the product away from dusty or humid areas.
• Do not use this product if it has been damaged or modified.
• Do not get this product wet. This may cause an electric shock or malfunction.
• Do not place this product near heat sources or leave under direct sunlight for an extended period. Overheating may cause malfunction.
• Do not touch the metal parts of the USB plug.
• Do not apply strong impact or weight on the product.
• Do not pull roughly or bend the cable of the product.
• Do not disassemble, modify or attempt to repair this product.
• If product needs cleaning, use only a soft dry cloth. Do not use any chemical agents like benzene or thinner.
• Do not use this product for anything other than its intended purpose. We are not responsible for any accidents or damages in the event of use other than the intended purpose.

Included

Platform

Xbox Series X|S / Xbox One / Windows 10

Before using this product with the Xbox Series X|S / Xbox One system, please read the included instructions carefully.
Please check that your Xbox Series X|S / Xbox One is updated to the latest system firmware.

This product is designed for the Xbox Series X|S, but it can also be used with the Xbox One and Windows 10 by following the instructions in this manual.

Layout

Steering unit

Foot pedals

How to attach Clamp

1. Tighten the clamp into the steering unit base with the clamp screw.
   
2. Use the clamp to secure the steering unit to a flat, hard surface (i.e. table).
   
   * Do not attach to furniture made from glass or other fragile materials.
   * Carefully detach from furniture to prevent damage to furniture or product.
3. Assemble the foot pedal as shown in the image below.
   

How to Connect

1. Connect the foot pedal unit modular connector to the steering unit modular connection port.
   
   * This product can be used without the foot pedals (Except "MODE-1").
2. Set the Mode Toggle Switch to the appropriate setting then connect the USB cable.
   * Do not press on any buttons when connecting the USB cable.
   * Check the connector direction before inserting.
   【"MODE-1"】(For Xbox Series X|S)
   * "MODE-1" may not function depending on the software. If that happens, please toggle to "MODE-2".
   
   【"MODE-2"】(If "MODE-1" does not function correctly for Xbox Series X|S or when connecting to a Windows 10 PC)
   
   Do not turn the steering wheel while you are connecting or turning on the Xbox Series X|S. It is calibrating the center position of steering wheel when connecting.

Quick Release

Your controller cord has a quick release. This is a safety feature designed to reduce the chance of the Xbox Series X|S / Xbox One console or computer from falling when the cord is pulled.

If the console or computer falls and hits someone, especially a small child, it could cause a serious injury.

To reduce the risk of injuries or damage to the console or computer, it is important to use the controller and the quick release properly. Use the controller connector, not the quick release, to routinely connect and disconnect the controller. If the quick release disconnects, simply reconnect it by aligning the grooved indentations and pressing the two parts completely together.

The controller will not work unless the quick release is connected properly. Never tape, glue, or otherwise prevent the quick release from pulling apart.

The quick release reduces, but does not eliminate, the risk of the computer or console being pulled off its surface.

To further reduce the risk:

• Do not allow anyone to pull on the controller or controller cord in a way that causes the computer or console to move.
• Do not allow controller cords to become crossed or tangled with one another.
  

Download App

『HORI Device Manager for Xbox Series X』

<How to Download>

1. Search for "HORI" on the Microsoft Store.
2. Install the "HORI Device Manager for Xbox Series X" App.

• About Profile
  The Profile Button is used to toggle between profiles (profiles are adjusted via the HORI Device Manager for Xbox Series X).
  
  Profiles will switch when the Profile Button is pressed.
  The Profile LED will change based on Profile setting.

  Profile Set	Profile LED
  1	Green
  2	Red
  3	Blue
  4	White

Main Features