Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FCI ASD-0003
Summary of Contents for FCI ASD-0003
- Page 1 MagicMoon Automatic Dispenser ASD-0003 Installation Manual Quality Guarantee *Thank you for choosing the automatic faucet soap dispenser. Please read the instruction carefully before installation. This manual is for your reference only. P a g e...
-
Page 2: Specifications
Features • Hands free sensor operation improves hand washing hygiene. • Easy installation and low-cost maintenance • Modular one-piece construction with chrome-plated cast brass spout and black throat plate • Available with hardwired or battery power Specifications Power 6V (4 x Alkaline D batteries) 5 –... -
Page 3: Before Installation
Before Installation • Locate position of soap dispenser. • Ensure that soap dispenser does not interfere with anything above or below the lavatory/counter top area • Pay special attention so that the sensor surface is not flawed or scratched during the installation process. -
Page 4: Tools You Will Need
Tools You will Need • Adjustable wrench • Power drill with 25 – 30 mm counter top drill bit • Phillips screwdriver • Utility knife • Hammer • Ruler/tape measure P a g e... -
Page 5: Part List
Part List Faucet Body Control Box Assembly Assembly Sensor Sensor cable female Nozzle Control box assembly cover Hex screw Control box base Spout Push button O Ring Hose clip Tapered Power cable washer Fixed frame Tube clip Suction tube Clear tubing Bottle cap Brass shank Soap bottle... -
Page 6: Part List Diagram
Part List Diagram P a g e... - Page 7 Construction / Installation Diagram 1. Faucet Soap Assembly Soap Dispenser oftentimes can be mounted in the left or right hole of a 100 m or 200 mm center-set sink. The ability to do this is contingent upon the width of the faucet spout and accessibility to the unit on the underside of the sink (the Motor and Soap Bottle cannot interfere...
- Page 8 Position spout to direct soap into the sink Screw the flange nut onto the shank and tighten. 2. Control Box Assembly (Including Battery Box) Determine a temporary position for mounting the foam tank & battery case units. Make sure foam tank unit is within reach of the liquid soap and air tube from the foam soap dispenser.
- Page 9 When installing onto a concrete wall, drill holes 30 mm deep using a 6 mm masonry drill bit. Insert wall anchors into the holes and mount the dispenser using screws. When installing onto a wood wall, drill holes using a 3 mm drill bit and attach the dispenser bracket using screws provided.
- Page 10 free of kinks and bends when connected. iii. Insert soap tube and air tube into respective fittings and secure with tube clamps. P a g e | 10...
- Page 11 Fill / Refill Soap Lift the soap bottle and horizontally pullout the bottle. Remove the plastic bottle cap. Fill the bottle with 2 parts water & one-part soap concentrate. Avoid overfilling the bottle. Return the bottle back into the case unit (fixture frame).
- Page 12 Fill / Refill Soap Diagram P a g e | 12...
- Page 13 Operations As the user’s hands enter the beam’s effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve allowing a single soap application to flow from the spout. P a g e | 13...
- Page 14 Soap Volume Adjustment No adjustments are required for most settings. Factory default soap volume is 4 ml. The factory setting should be satisfactory for most installations. To adjust the volume, aim the remote control at sensor eye. Press the plus “Time +” to increase the soap volume and “Time –...
- Page 15 Soap Dispensing Range Adjustments To adjust the dispensing range: 1. On the remote press the auto adjust button. 2. Place hand at the desired distance. The LED will flash for 1 sec then stays on for 3 secs to confirm setting. P a g e | 15...
-
Page 16: Battery Replacement
Battery Replacement 1. Disconnect the power cables. 2. Remove the black battery holder from the case unit 3. Using a Philips screw driver, remove the two Philips screws, plastic cover and the four D size batteries. 4. Replace with 4 new batteries, place back the cover and tighten the assembly. -
Page 17: Troubleshooting
Troubleshooting 1. Unit does not operate Check battery power cables are connected. Connect power cables. 2. Soap does not dispense Soap bottle needs refill. Refill 2:1 water & soap. Check soap dispensing nozzle for clog. Clean nozzle with soft cloth. 3. -
Page 18: Care And Cleaning
Care & Cleaning DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean faucet that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. - Page 19 Resources For Installation guides, visit our resource page through the QR code Alternatively, you can visit our resource page at https://faucetscanada.ca/resource To view more products from Faucets Canada, visit our shop page through the QR code. Alternatively, you can visit our shop page at https://faucetscanada.ca/shop/ Warranty Information...
- Page 20 About us Here at FCi, our main goal is to break the eco- innovation boundary and provide customers with fixtures that save water and deliver reliable sources of sanitation every time. As Canada’s favourite automatic faucet brand, we are proud to say we deliver quality touchless fixtures that perform beyond expectations and exceed design standards.