Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FCI MagicRound ASD-0001
Summary of Contents for FCI MagicRound ASD-0001
- Page 1 MagicRound Automatic Soap Dispenser ASD-0001 Installation Manual Quality Guarantee *Thank you for choosing the automatic wall mount soap dispenser. Please read the instruction carefully before installation. This manual is for your reference only. P a g e...
-
Page 2: Specifications
Features • Hands free sensor operation improves hand washing hygiene. • Easy installation and low-cost maintenance • Battery powered. • Stainless steel finish • Suitable for schools, offices, supermarkets, hospitals, and other high- volume facilities Specifications Power Supplied 9V (6 x AA Alkaline batteries) 5 –... -
Page 3: Before Installation
Before Installation • Locate position of soap dispenser. • Ensure that soap dispenser does not interfere with anything above the lavatory/counter or shining surface top area. Must be installed 250 mm above the counter. • Pay special attention so that the sensor surface is not flawed or scratched during the installation process. -
Page 4: Tools You Will Need
Tools You will Need • Power drill with 6 mm wall drill bit • Flat head screwdriver • Phillips screwdriver • Ruler/tape measure P a g e... -
Page 5: Part List
Part List P a g e... - Page 6 Construction / Installation Diagram Using the supplied black plastic key, open & remove the upper cover. Disconnect the battery power and remove the battery holder Using a Philips screw driver remove iii. the upper right-hand Phillips screw and remove the steel wall mount plate (wall build-up frame).
- Page 7 Remove the white plastic cap & fill vii. the soap cartridge with soap. Do not overfill the soap cartridge to the top the cap. Assemble back the battery holder viii. and tighten the holder onto the upper cover. Connect the battery power cable. Place &...
- Page 8 P a g e...
- Page 9 Operations As the user’s hands enter below the beam’s effective range (5 – 15 cm), the beam is reflected back into the sensor receiver and activates the solenoid valve allowing a single soap application to flow from the dispenser. P a g e...
- Page 10 Soap Volume Adjustment No adjustments are required for most settings. Factory default soap volume is 1 ml. The factory setting should be satisfactory for most installations. To invoke the volume adjustment, press the button below the dispenser and hold it until the LED starts flashing slowly, about five seconds.
- Page 11 Soap Dispensing Range Adjustments No adjustments are required for most settings. Factory default range is set at 1 cm. The factory setting should be satisfactory for most installations. To invoke the sensing range adjustment, press the button below the dispenser and hold it until the LED starts flashing slowly, about five seconds.
-
Page 12: Battery Replacement
Battery Replacement The sensor LED will flash continuously & rapidly to indicate low battery power. Using the supplied black plastic key, open & remove the upper cover. Disconnect the battery power and remove the battery holder. To remove the battery holder, iii. -
Page 13: Troubleshooting
Troubleshooting 1. Unit does not operate Check battery. Remove & replace 3 AA size batteries. 2. Soap does not dispense Soap bottle needs refill. Refill soap. Check soap dispensing nozzle for clog. Clean nozzle with soft cloth. P a g e | 13... -
Page 14: Care And Cleaning
Care & Cleaning DO NOT USE abrasive or chemical cleaners (including chlorine bleach) to clean dispenser that may dull the luster and attack the special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the dispenser from any splattering of cleaner. - Page 15 Resources For Installation guides, visit our resource page through the QR code. Alternatively, you can visit our resource page at https://faucetscanada.ca/resources/ To view more products from Faucets Canada, visit our shop page through the QR code. Alternatively, you can visit our shop page at https://faucetscanada.ca/shop/ Warranty Information...
- Page 16 About us Here at FCi, our main goal is to break the eco- innovation boundary and provide customers with fixtures that save water and deliver reliable sources of sanitation every time. As Canada’s favourite automatic faucet brand, we are proud to say we deliver quality touchless fixtures that perform beyond expectations and exceed design standards.