Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ViewZ VZ-CMK03
Summary of Contents for ViewZ VZ-CMK03
- Page 1 INSTALLATION INSTRUCTIONS Tilting Wall Mount for 26˝ to 40˝ ViewZ Monitors VZ-CMK03 NORTH AMERICA 1220 N. Kraemer Blvd. Anaheim, CA 92806 USA USA and Canada Phone: 1-888-99-ViewZ Other Locations Phone: (001) 714-630-3380 Fax: (001) 714-630-2335 853177002885...
-
Page 2: Table Of Contents
PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. VIEWZ DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VIEWZ PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS... -
Page 3: Installation Tools
Phillips Head Screwdriver Parts List Your ViewZ product is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact Viewz at 1-888-99-ViewZ. -
Page 4: Mounting Hardware
Nylon Spacers and Flat Washers You may stack the nylon spacers to achieve proper spacing. ˝ ½˝ Nylon Spacer (Large) ¼˝ Nylon Spacer (Small) Flat Washer (Metal) (Qty 6) (Qty 6) (Qty 6) Page 4 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 5: Features
Mounting Rails Locking Safety Screws Allow lateral adjustments when mounting the flat panel. Prevent the flat panel from being removed or dislodged from the wall plate. Installation Instructions Page 5 Visit the ViewZ website at http://www.viewzusa.com... -
Page 6: Installing The Wall Plate
VZ-CMK03 Installing the Wall Plate Introduction Directional Mounting Arrow The Directional Mounting Arrow stamped into the VZ-CMK03 wall plate indicates which edge is the top. Mounting Safety Two people are recommended to install the wall plate. You must secure the wall plate to two (2) wall studs with six (6) lag bolts (3 lag bolts for each stud found). - Page 7 Do not overtighten the lag bolts when attaching the mount to the wall. Improper installation may result in personal injury or property damage. Proceed to the “Installing the Mounting Bracket” on page 8. Installation Instructions Page 7 Visit the ViewZ website at http://www.viewzusa.com...
-
Page 8: Installing The Mounting Brackets
Small Straw or Toothpick Go to “Griplate™ Washer Installation” on page Small Straw Depth Plus 1/8” Allowance Small Straw Depth Plus 1/8” Allowance or Toothpick or Toothpick Mark Mark Page 8 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 9: Griplate™ Washer Installation / Nylon Spacer Installation
Mounting Bracket ™ Griplate Washer Nylon Spacer Installation ViewZ’s nylon spacers allow you to attach the mounting Flat Panel bracket to flat panels which have recessed or uneven mounting points. Each nylon spacer will add distance Nylon Spacer between the mounting bracket and the flat panel. -
Page 10: Attaching The Mounting Brackets To The Flat Panel
2) Slide the flat panel down slowly, keeping it close to the wall. 3) Engage the top and bottom mounting brackets to the rails of the wall plate. Page 10 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... -
Page 11: Safety Knurl Knob Installation
The safety knurl knobs keep the flat panel from being accidently dislodged from the VZ-CMK03. Fully extend the flat panel away from the wall. 1) Install and tighten a safety knurl knob at the top of one of the mounting brackets. -
Page 12: Locking Safety Screw Installation
VZ-CMK03 Locking Safety Screw Installation The locking safety screws keep the flat panel from being accidently dislodged from the VZ-CMK03. 1) Thread an M6 x 30mm locking safety screw at the bottom of one of the mounting brackets. M6 x 30mm... -
Page 13: Technical Specifications
VZ-CMK03 Technical Specifications All measurements are in inches [millimeters]. Installation Instructions Page 13 Visit the ViewZ website at http://www.viewzusa.com... -
Page 14: Part 2 Instructions
INSTALLATION INSTRUCTIONS VZ-CMK03 PART 2 Ceiling Mount Adapter... - Page 15 Phillips Tip Screwdriver Socket Wrench Ladder Parts List Make sure your Viewz product has the following hardware and components before beginning installation. If there are parts missing and/or damaged, stop the installation and call ViewZ at (888) 99-ViewZ. VZ-CMK-P2 Hardware M10 Nut...
- Page 16 Attaching The Ceiling Adapter Step 1 Before the following steps are begun, the appropriate suspension device must be installed. ViewZ offers the VZ-CMK-P3 or a standard 1-1/2” NPT extension pipe. Please see the installation instructions that are included with these respective mounting configurations.
- Page 17 A Phillips head screwdriver is required to perform the following step. 1) Once the ceiling adapter has been attached, tighten the M6 x 12mm Phillips head set screw using a Phillips screwdriver. VZ-CMK-P2 Installation Instructions Page 17 Visit the ViewZ website at http://www.viewzusa.com...
- Page 18 1) Once the two units have been attached together, use a 17mm socket wrench and a 17mm wrench to tighten the M10 hardware. *Mount shown for illustration purposes only (not included) Page 18 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com...
- Page 19 VZ-CMK03 Technical Specifications All measurements are in inches [mm]. Installation Instructions Page 19 Visit the ViewZ website at http://www.viewzusa.com...
-
Page 20: Part 3 Instructions
1) Remove the adjustments screws to adjust the height. 2) Re-insert adjustment screws into holes once pipe is at the desired length. Page 20 Installation Instructions Visit the ViewZ website at http://www.viewzusa.com... - Page 21 All measurements are in inches [mm]. 6.72 170.7 4.50 114.3 4.50 114.3 4.50 114.3 Ø. 41 10.3 (CABLE ACCESS) 1.06 ADJUSTABLE 26.9 1.5" NPT PIPE THREADS 1.00 25.4 2.50 63.5 27.0 685.5 44.0 1117.3 Installation Instructions Page 21 Visit the ViewZ website at http://www.viewzusa.com...
-
Page 22: Warranty
What ViewZ Will Do At the sole option of ViewZ, ViewZ will repair or replace any product or product part that is defective. If ViewZ chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs.
Need help?
Do you have a question about the VZ-CMK03 and is the answer not in the manual?
Questions and answers