Advertisement
Quick Links
Step 1: Upright posts
8- 3/8" x 1" carriage bolts SS
8- 3/8" flange nuts
Step 2: Footpads and Legs
4- 3/8" x 3-1/2" bolts SS
4- 3/8" flange nuts
4- Long leg pins
4- hair pin clips SS
Step 3: Winch mount
2- 3/8" x 1" carriage bolts SS
2- 3/8" flange nuts
Premier Vertical Lift
Instructions
Step 4 and 5: Base tubes
16- 3/8" x 1" carriage bolts SS
16- 3/8" flange nuts
Step 6: Cable mount brackets
6- 3/8" x 1" carriage bolts SS
6- 3/8" flange nuts
Step 7: V braces
4- 3/8" x 2-3/4" bolts SS
1- 3/8" x 1-1/2" bolts SS
3- 1/2" x 6" bolts SS
5- 3/8" flange nuts
3- 1/2" aluminum nuts
Step 8: Bed and cables
8- 3/8" x 1" carriage bolts SS
8- 3/8" flange nuts
Step 9: Cable mounts
4- 5/16" x 1" carriage bolts SS
4- 5/16" flange nuts
10- 5/8"-11 aluminum nuts
Step 10: Flat braces
4- 3/8" x 2-3/4" bolts SS
4- 3/8" x 1" carriage bolts SS
4- 3/8" flange nuts
Cable Mount Bracket caps
3- 1-1/2" x 3" Black Caps
www.harbor-master.com
Advertisement
Summary of Contents for harbor master Premier Verical Lift
- Page 1 Premier Vertical Lift Instructions Step 4 and 5: Base tubes Step 8: Bed and cables Step 1: Upright posts 16- 3/8” x 1” carriage bolts SS 8- 3/8” x 1” carriage bolts SS 8- 3/8” x 1” carriage bolts SS 16- 3/8”...
- Page 2 Step 1- The Uprights Unpackage the bundles. Lay all parts out on a level surface. Locate the (2) lower side beams. The left lower side beam ends will be labeled A and D. The right lower side beam will be labeled B and C. Locate the (4) upright posts.
- Page 3 Step 2- The Leveling Legs Locate the (4) leveling leg posts and the (4) foot pads. Insert the legs in to the foot pads and secure with 3/8” x 3-1/2” bolt and 3/8” flange nut. Insert legs into the upright posts on each corner. Secure with leg pin and clip.
- Page 4 Step 4- The Front and Rear Base Tubes Go to corner C. Slide the head of (2) 3/8” x 1” carriage bolts into the slot on the upright post and slide into the slot on the top of the angle of the end of the base tube.
- Page 5 Step 6- Cable mounting bracket Locate the (3) cable mounting brackets. Insert the head of (1) 3/8” x 1” carriage bolt into the outer nut channel on upright B. Hand tighten (1) 3/8” flange nut on the carriage bolt. Slide (1) cable mounting bracket down the upright. The cable mounting bracket should run parallel with the side beam and is flush with top of the upright post.
- Page 6 Step 8- Bed and Cables Lay (1) piece of wood diagonally over every corner. Locate the load tubes labeled A-D and B-C. Lay them inside the frame on top of the wood so they correspond with their labeled corners. Locate the spreader tubes that correspond with the correct corners (the spreader tubes have the angles welded to the ends).
- Page 7 Repeat the spreader tube to load tube connection for corner D. Move to corner C, insert the head of (1) 3/8” x 1” carriage bolt into the top nut channel and bottom nut channel. Repeat for the opposite end or corner B. Also, remove the large nut on the bolt for the pulley in the load tubes that were preset for you.
- Page 8 Starting on corner A, take the lower cable and slide it into the slot on the lower angle of the side frame bottom tube. Place (1) 5/16” x 1” carriage bolt in the slot to hold the cable in place. Tighten 5/16”...
- Page 9 Step 9- Winch cable and wheel mount Attach winch cable from spreader tube into spool on winch as shown. Using vise grip pliers, hold the chain and attach the wheel to the winch with the clutch disk, gear and thrust washer behind wheel. You can just thread the wheel onto the shaft hand tight.