Advertisement
Available languages
Available languages
OBJ_BUCH-2707-002.book Page 7 Wednesday, November 2, 2016 11:08 AM
Cordless Impact Screwdriver
Permitted ambient temperature
– during charging
**
– during operation
and during
storage
Recommended batteries
Recommended chargers
* depending on the battery pack being used
** Limited performance at temperatures <0 °C
***
only for wireless charging batteries
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-2.
Typically the A-weighted noise levels of the product are:
Sound pressure level 100 dB(A); Sound power level
111 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-2:
Impact tightening of fasteners of the maximum capacity of the
2
2
tool: a
=18 m/s
, K=1,5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Only for EC countries:
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-2,
EN 50581.
Bosch Power Tools
Technical file (2006/42/EC) at:
GDS 18V-EC
Robert Bosch Power Tools GmbH, PT/ECS,
300 ABR
70538 Stuttgart, GERMANY
Henk Becker
Executive Vice President
°C
0... +45
Engineering
°C
-20... +50
GBA 18V..
GBA 18V...W
AL 18..
Robert Bosch Power Tools GmbH
GAL 3680
70538 Stuttgart, GERMANY
GAL 18...W**
Stuttgart, 01.01.2017
Assembly
Battery Charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 4 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 5 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 4, press the unlocking button 5 and
pull out the battery toward the front. Do not exert any force.
Changing the Tool (see figure A)
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
English | 7
Helmut Heinzelmann
Head of Product Certification
PT/ECS
1 609 92A 3L6 | (2.11.16)
Advertisement
