Related Manuals for Feider Machines FBVE3000
Summary of Contents for Feider Machines FBVE3000
- Page 1 ORIGINAL INSTRUCTIONS INSTRUCTION MANUAL SILENT SHREDDER FBVE3000 READ THIS INSTRUCTIONS MANUAL BEFORE USE THE TOOL FEIDER 32, rue Aristide Bergès - ZI 31270 Cugnaux – France Made in PRC...
- Page 6 DEFINITONS OF SYMBOLS Caution! Read the instruction manual and follow the warning and safety instructions! Keep bystanders away! Danger – Rotation blades. Keep hands and feet out of openings while machine is running. Wear eye and ear protection Caution! Remove plug from the mains immediately if cable is damaged or cut. Degree of protection against water: IPX4 Sound power level, measured according to 2000/14/EC...
-
Page 7: Safety Instructions
Safety instructions Warning! Please read and follow the safety instructions carefully. 1. The shredder must be assembled correctly before use. 2. Warning! This appliance must be earthed! 3. Warning! Use only three-core extension cables with the earth wire connected. 4. Only use extension cables that are approved for outdoor use and check that they are in good condition before use. - Page 8 13. Before leaving the shredder, switch off the motor and unplug the connection cable. Proceed in the same way in the event of a power failure. 14. Keep children and pets away. All onlookers should be kept at a safe distance away from the shredder when it is in use. 15.
- Page 9 shredder as such foreign bodies could cause blunting of the chopping knife and seriously damage the motor. Do not use your shredder for any purposes other than having been designed for. 30. If the shredder should start to vibrate abnormally, immediately switch off the motor and check for the cause.
-
Page 10: Technical Data
38. Attention! Through poor conditions of the electrical MAINS, shortly voltage drops can appear when starting the EQUIPMENT. This can influence other equipment (eg. Blinking of a lamp). If the MAINS-IMPEDANCE Zmax<0.376OHM(MK- L772), such disturbances are not expected. (In case of need, you may contact your local supply authority for further information). - Page 11 Preparation Warning! Do not allow children to operate this equipment. Do not operate this equipment in the vicinity of bystanders. Wear ear protection and safety glasses at all times while operating this machine. Avoid wearing clothing that is loose fitting or that has hanging cords or ties. Only operate the machine in an open space (e.g.
- Page 12 Always use the correct supply voltage The power supply voltage must match the information quoted on your shredder's identification plate. Shredders with a rating of 230 V can only be connected to a 230 V mains supply. The shredder shall be supplied via a residual current device (RCD) with a tripping current of not more than 30mA An extension cable with a cross section that is too small causes a distinct reduction in the performance capabilities of the machine.
- Page 13 Operation instructions Warning Before starting the machine, look into the feeding chamber to make sure that it is empty. Keep your face and body away from the feed intake opening. Do not allow your hands or any other part of your body or your clothing to get inside the feeding chamber, discharge chute, or near any moving part.
- Page 14 Emptying the collection box The level of shredded material debris in the collection box can be checked by looking through the notches on the upper face of the base frame. Always empty the collection box in good time to prevent it from overfilling. To empty it, proceed as follows: a) Switch off the device at the ON/OFF switch.
-
Page 15: Troubleshooting
Troubleshooting The motor does not run The overload protection has responded Set the reversing switch to position B and press the reset button, keep the on/off switch pressed to switch on the shredder for a short period. After the blocking has been removed, reset the reversing switch to position A. - Page 16 e) Put the motor unit down into the collection box. (Fig. 8-2)) Store the machine in a dry place. For extended storage periods, run the unit dry for a short time. Always allow the machine to cool down before storing it. When servicing the chopping knife assembly be aware that, even though the motor will not ...
- Page 18 EXPLOSION DRAWING AND PART LIST Part Nr. Description KND2-12/2 Reversing switch KJD17FT On/off switch Screw ST4.2X16 MK-L771-07 Switch location plate Overload protector MK-L771-05 Top cover Mk-L771-20 Feeding funnel MK-L79-12-0 Plug MK-L771-01 Above shell MK-L771-03 Front cover of shell Screw ST4.2 X16 Screw M8x25 MK-L771-04 Location plate...
- Page 19 MK-L771-18 Adjuster MK-L771-06 Cover of steel frame Capacitor MK-L771-13-0 Steel frame GB/T96-85 Big grommet 5 MK-L771-08 Safety switch knob MK-L771-14 Safety switch plate GB/T846-85 Screw ST4.2X16 MK-L17-17 Wheel MK-L771-16 wheel shaft GB/T96-85 Grommet 8 GB93-87 Spring grommet 8 GB70-85 Screw M8x70 MK-L17-19 MK-L771-17 Collection box...
- Page 20 FEIDER ZI, 32 rue aristide Bergès – 31270 Cugnaux - France Declares that the machinery designated below: SILENT SHREDDER FBVE3000 Serial number: 20200735205-20200735604 Complies with the provisions of the Directive “machinery” 2006/42/EC and national laws transposing it: Also complies with the following European directives:...
-
Page 21: Warranty
WARRANTY WARRANTY The manufacturer guarantees the product against defects in material and workmanship for a period of 2 years from the date of the original purchase. The warranty only applies if the product is for household use. The warranty does not cover breakdowns due to normal wear and tear. The manufacturer agrees to replace parts identified as defective by the designated distributor. -
Page 22: Product Failure
PRODUCT FAILURE WHAT TO DO IF MY MACHINE BREAKS DOWN? If you bought your product in a store: a) Empty the fuel tank. b) Make sure that your machine is complete with all accessories supplied, and clean! If this is not the case, the repairer will refuse the machine. -
Page 23: Warranty Exclusions
WARRANTY EXCLUSIONS THE WARRANTY DOES NOT COVER: • Start-up and setting up of the product. • Damage resulting from normal wear and tear of the product. • Damage resulting from improper use of the product. • Damage resulting from assembly or start-up not in accordance with the user manual. •...