Remington HF9000 - Heritage Series Shaver Manual

Overview

1. Shaving foils
2. Trimmer
3. On/off switch
4. Hair pocket
5. Pop-up trimmer
6. Foil assembly release button
7. Charging indicator.
8. Charging connector. Includes USB cable (not shown)

Getting Started

It is recommended that you use your new shaver daily for up to two weeks to allow time for your beard and skin to become accustomed to the new shaving system.
Your Remington Sensitive Foil shaver has been designed to help reduce irritation and ingrowing hairs for men who experience these conditions when shaving. The lifting combs at both edges of the cutting head help lift flat lying, longer hairs and feed them into the cutters. The shaver is designed to cut hairs at or slightly above the skin surface to help prevent ingrown hairs. For best results, it is recommended to use the shaver daily or every other day to maintain hair length and to reduce ingrowing hairs.

Charging

Note: It is recommended to fully charge your appliance before using for the first time. Please refer to the charge times shown in this book.

1. Connect the cord to the shaver and then to the electrical outlet. The charging indicator light will glow green.
2. Charge your new shaver for 2 hours before its first use. This first charge is important to the shaver's battery life.

• Ensure the product is switched off.
• Connect the adaptor to the product and then to the mains.
• Run time from fully charged is up to 60 minutes.

Note: To preserve the life of your batteries, let them run out every 6 months then fully charge.

Charging Indicator

Shave

Before using, read the important safety instructions in front of the manual.

1. Begin by removing the protective head guard from your shaver.
2. Slide the on/off button up to turn on. (Dia. D)
3. Slide trimmer button up to engage and use it to remove long hair first. Then close down when finished. (Dia. E_F)
4. Stretch the skin with your free hand so the hairs stand upright.
5. Hold the shaving head so all screens touch your skin simultaneously. The independently floating screens automatically adjust to the contours of your face. Only apply light pressure on the shaving head while shaving and use short, circular strokes. (Dia. G)
6. After shaving, turn the shaver off.(Dia. D)

*We recommend that you use your new shaver daily for up to three weeks to allow time for your hair and skin to become accustomed to the new shaving system.**

Shaving Tips

• Ensure your skin is dry and free of oils.
• Wait at least 15 minutes after getting up before shaving, to ensure your face is free of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so the screens are touching the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for them to enter the cutting chamber.
• Shave with short, circular strokes. The use of short, circular motions in stubborn areas may obtain a closer shave, especially along the neck and chin line.
• Do not press hard against the skin in order to avoid damage to the screens.

Trim

1. Slide trimmer release button up to engage trimmer.
2. Trim long, difficult hairs and side burns.
3. Close trimmer by pressing down.

Battery Removal

When your rechargeable shaver reaches the end of its useful life, the batteries must be removed from the shaver and recycled or disposed of properly in accordance with your state and local requirements. If this is not required by law, you may elect to dispose of the shaver with the batteries.
This device uses one of the following types of rechargeable batteries: nickel metal hydride (NiMH), nickel cadmium (Ni-Cd) or Lithium Ion (Li-Ion) (see included battery for indication of type).

ALL RECHARGEABLE BATTERIES MUST BE RECYCLED OR DISPOSED OF IN ACCORDANCE WITH APPLICABLE STATE AND LOCAL REGULATIONS. DO NOT PUT IN FIRE OR MUTILATE, AS THE BATTERY MAY BURST OR RELEASE TOXIC MATERIALS. DO NOT SHORT-CIRCUIT, AS THIS MAY CAUSE BURNS.

To Remove the Rechargeable Battery:

1. Remove phillips head screw from lower back panel of shaver.
2. Pry the back panel off the shaver releasing the snap fits.
3. Snip the battery wires and remove the batteries.
4. Dispose of batteries properly.

Cleaning & Care

NOTE: **When cleaning your shaver, make sure the shaver is turned off and disconnected from the power cord.**

For optimal shaver performance, clean your shaver after each use.

• Do not remove or replace head assembly while shaver is running as it may cause damage to the unit's screens and cutters.
• To clean the external surfaces of the shaver, use a damp cloth. Do not use strong detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer or heater to dry the shaver.
• The shaver should not be used until it has dried.
• Lubricate each cutter with household oil.
• This shaver has no user serviceable parts.

Daily Cleaning:

1. Grasp the sides of the cutter assembly and pull away from the shaver body.
2. Tap the stubble from the foils and cutters.
3. Replace the hairpocket assembly.

Monthly Cleaning:

1. Grasp the sides of the cutter assembly and pull away from the shaver body.
2. Tap the stubble from the foils and cutters.
3. Use the cleaning brush to delicately sweep any loose hairs from the cutters and trimmer.
4. After cleaning, replace the hairpocket assembly.

Replacements

Replacing the Foils & Cutters

To ensure the continued highest quality performance from your shaver, we recommend that foils and cutters are replaced regularly.
Signs that your foils and cutters need replacing:

• Irritation: As foils get worn, you may experience skin irritation.
• Pulling: As the cutters wear, your shave may not feel as close and you may feel your cutter pulling your hair.
• Wear through: You may notice that the cutters have worn through the foils.

To Replace the Foil

1. Grasp the foil carrier grips on the sides of the shaver and pull up to remove the foils. Discard the used foils.
2. Snap a new foil carrier in place.

To Replace the Cutters

1. Remove the foil carrier.
2. Depress cutter and rotate it 90° counterclockwise and lift off. Do not lose spring.
3. Place new cutter on oscillator tip, depress and rotate 90° counterclockwise.

NOTE: Do not press on the cutter ends as this may cause damage.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Remington HF9000 - Heritage Series Shaver Manual