ENDA ETC1311 Manual

Please read this document carefully before using this product. The guarantee will be
invalidated if the device is damaged by not following instructions detailed in the
manual. The company shall not be responsible for any damage or losses however
caused, which may be experienced as a result of the installation or use of this product.
ENDA ETC1311 DIGITAL THERMOSTAT
Thank you for choosing ENDA ETC1311 temperature controller.
* 35 x 77mm sized.
* On-Off control.
* J, K, Pt100 or Pt1000 input.
* Temperature compensation.
* In the case of probe failure, heating can be
selected on, off or periodical running.
* Upper and lower limits of the setpoint can be
adjusted.
* Set value can be adjusted by using single key.
* CE marked according to European Norms.
Order Code : ETC1311- -
1 2
1 - Input
2 - Supply Voltage
FE.....Fe-Const (J) 230VAC...230V AC
RT.....Pt100 24VAC.....24V AC
PT.....Pt1000
12VAC.....12V AC
K.......NiCr-Ni (K) SM...........9-30V DC / 7-24V AC
Connection Diagram
ENDA ETC1311 is intended for installation in control panels. Make sure that the device is
used only for intended purpose. The electrical connections must be carried out by a
qualified staff and must be according to the relevant locally applicable regulations. During
an installation, all of the cables that are connected to the device must be free of electrical
power. The device must be protected against inadmissible humidity, vibrations, severe
soiling and make sure that the operation temperature is not exceeded. The cables should
not be close to the power cables or components.
ENDA ENDA
INDUSTRIAL ELECTRONICS INDUSTRIAL ELECTRONICS
ETC1311-K-230VAC ETC1311-FE-SM-P
DIGITAL THERMOSTAT DIGITAL THERMOSTAT
SN: XXXXXXXXX SN: XXXXXXXXX
K (NiCr-Ni)
-
+
1 2 3 4 5 6 7 8 9 10 11 12 1 2 3
Equipment is protected throughout
by DOUBLE INSULATION.
NOTE:
Fuse
SUPPLY: F 100 mA
Switch
250V AC
4 Line
184-253V AC
50/60Hz 4VA
5
Neutral
Fuse should
Cable size: 1,5mm²
be connected
OUT
ENDA
-
3
3 - Output
P......... Relay-16A
None...Relay-8A
SSR....Logic output
ENDA
INDUSTRIAL ELECTRONICS
ETC1311-RT-12VAC
DIGITAL THERMOSTAT
SN: XXXXXXXXX
J (Fe-CuNi)
-
+
4 5 6 7 8 9 10 11 12 1 2 3 4 5 6
Holding screw 0.4-0.5Nm
Note:
1) Mains supply cords shall meet the requirements of
IEC 60227 or IEC 60245.
230V AC
2) In accordance with the safety regulations, the power
Supply
supply switch shall bring the identification of the
relevant instrument and it should be easily
accessible by the operator.
Technical Specifications
ENVIRONMENTAL CONDITIONS
Ambient/storage temperature
Max. relative humidity
Rated pollution degree
Height
Do not use the device in locations subject to corrosive and flammable gasses.
ELECTRICAL CHARACTERISTICS
Supply voltage
Power consumption
Wiring
Scale
Accuracy
°C
Indicator
PRG EMC
SET
Safety requirements
ETC1311
OUTPUT
HEAT OUT
Life expectancy for relay
CONTROL
Control type
Control algorithm
Hysteresis
HOUSING
Housing type
Dimensions
Weight
Enclosure material
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
Dimensions
OUT
ENDA
Pt100
7 8 9 10 11 12
SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.
Yukarý Dudullu Barbaros Cad. Kutup Sok. No:20 34775 - ÜMRANÝYE/ÝSTANBUL/TÜRKÝYE
Tel : +90 216 499 46 64 Pbx.
1/2
url : www.enda.com.tr
0 ... +50°C/-25 ... 70°C (with no icing)
80 , up to % 31°C decreasing linearly 50% at
According to EN 60529 Front panel : IP65
Rear panel : IP20
Max. 2000m
230V AC +10% -20%, 50/60Hz or 24V AC 10%, 50/60Hz or 12V AC 10%, 50/60Hz or ±
optional 9-30V DC / 7-24V AC 10% SMPS module. ±
Max. 4VA
2.5mm² screw-terminal connections.
0 .... +600°C for Fe-Const (J) and NiCr-Ni (K).
± 0.5% (of full scale) ±1 digit
3 digits, 14.2mm, 7 segment red LED
EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.
The device is designed to operate in controlled electromagnetic environment)
EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)
For ETC1311-XX-XX ; Relay: 250VAC, 8A(
For ETC1311-XX-XX-P ; Relay: 240VAC, 16A(for resistive load), NO or 12VDC 20mA logic out.
For ETC1311-XX-XX ; Mechanical 30.000.000; Electrical 100.000 operation.
For ETC1311-XX-XX-P ; Mechanical 30.000.000; Electrical 30.000 operation.
Single-setpoint control
On-Off control
Adjustable between 1 ... 20°C.
Suitable for flush-panel mounting.
W77xH35xD71mm
Approx. 198g (A fter packing )
Self extinguishing plastics
77mm For removing mounting clamps:
Push the flush-mounting
clamp in direction 1 as shown
°C
in the figure below. Then, pull
PRG
SET
out the clamp in direction 2.
ETC1311
Flush mounting
clamp
Panel cut-out
71mm
1
Fax : +90 216 365 74 01
40 °C
±
-100 .... +600°C for Pt100 and Pt1000
for resistive load ), NO+NC,
Depth
71mm 5mm
Flush mounting
Panel
Rubber
clamp
2
packing
Note : 1) Panel thickness
should be maximum
7 mm.
2) If there is no 60mm
free space at the back
side of the device, it
would be difficult to
remove it from the
Panel.
ETC1311-E-10-R