200hz lcd tv signature series in full hd, premium series in full hd, true cinematic series, modern classic series, sleek & stylish series, home theatre systems, portable dvd players (2 pages)
Page 1
HISTORY Model Name KDL-40/46/55X4500 SERVICE MANUAL Click on Page Number to display detail of changes. Date Part Number Description of Revisions Version 2008.09 9-883-412-01 Original Manual. 2008.09 9-883-412-02 Add inverter board part number for 40 inches. (P.79)
Page 2
EG1H SERVICE MANUAL CHASSIS MODEL DEST KDL-40X4500 AEP/UK KDL-46X4500 AEP/UK KDL-55X4500 AEP/UK RM-ED012 FLAT PANEL COLOR TV - 1 -...
COMPONENTS IDENTIFIED BY SHADING AND MARKED THE EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. - 2 -...
Due to the higher melting point of Lead Free Solder the soldering iron tip temperature needs to be set to 370 degrees centigrade. This requires soldering equipment capable of accurate temperature control coupled with a good heat recovery characteristics. For more information on the use of Lead Free Solder, please refer to http://www.sony-training.com UK PLUG WARNING WARNING (UK Models only) The flexible mains lead is supplied connected to a B.S.
Page 5
CAUTION Attachment of HIROSE MDF 61 connector 1. Insertion (2) Press the center of (3) Slide the (1) Hold the center the connector to insert slider to lock the of a connector connector Lock Detachment of HIROSE MDF61 connector 2. Detachment (2) Press the center (1) Slide the slider to lock tab to release...
CONNECTORS 21 Pin Connector (SCART) Pin No Signal Signal level Audio output B Standard level : 0.5V rms (right) Output impedence : Less than 1kohm* Audio input B Standard level : 0.5V rms (right) Output impedence : More than 10kohm* Audio output A Standard level : 0.5V rms (left)
EG1H SELF DIAGNOSTIC SOFTWARE The identification of errors within the EG1H chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty.
Page 9
SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurrences of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: ( Info/Text reveal ) ( Volume )
2-5. CB1 Board Removal 2-6. D4 Board Removal (40 inches) Screws Screws To remove the CB1 board disconnect all connectors and then remove To remove the D4 board disconnect all connectors and then remove the 6 screws circled and ease the board gently away from the back of the the shield.
2-9. G7 Board Removal (55 inches) 2-10. GL Board Removal (46 & 55 inches) Screws Screws To remove the G7 board disconnect all connectors and then remove the To remove the GL board disconnect all connectors and then remove the 4 screws circled and ease the board gently away from the back of the 6 screws circled and ease the board gently away from the back of the TV set.
2-13. H4 Board Removal 2-14. K2 Board Removal Clip Screws To remove the H4 board disconnect the connector and then release the To remove the K2 board disconnect all connectors and then remove the clip circled and gently ease the board towards you and away from the 4 screws circled and ease the board gently away from the back of the back of the TV set.
SECTION 3 SERVICE MENUS 3-1. How to enter Service Mode 3-4. Entering BEM Service Menu Service adjustments to this model can be performed using the Press “Previous channel ” on the remote commander and the supplied remote Commander RM-ED012. BEM menu appears (See Pic.4) Turn on the power to the TV set and enter into the stand-by Pic.4 mode.
3-7. Trouble Shooting 3-7-1. No Power 3-7-9. Balancer Error When the TV Set has a Balancer board error please check the When the TV Set has no power please see flowchart [A]. following:- 3-7-2. Set Reboots Check the BE micro pin 163 on the FBA board. When the TV Set tries to restart please check the following:- Check harness connection CN6700 on the D4 board and CN104 on tne balancer board of panel module (40 inches).
Page 29
AE - EG1H AU_PROT L : Fa u l t MAIN_SW_FAULT Q1802 0 0 1 : 2 J UNR52A1G0LS0 D3.3V SP_MUTE_2 D1801 C1822 D1802 C1821 0 . 1 RB1815 1005 C1812 LINE_OUT_L GND_1 LINE_OUT_R C1813 L1804 10uH R1802 R1803 LINE_OUT 005:11G 470k 470k...
Page 30
AE - EG1H 3.3V LINEAR REGULATOR IC1900 PQ070XNA1ZPH +5V_ANALOGUE 6.1V R1923 JL1900 +3V3_DEMOD FL1901 R1918 +3V3_DEMOD L1902 L1903 TUNER_LNA_SW Pin3 UFE-4 Reception R1913 +3V3 C1901 C1902 JL1903 0 . 1 GND_1 JL1901 H I G H G N D C O F D M D I G I TA L C1922 C1925 C1920...
Page 35
CB1 - EG1H 1.2V Reg 12V 1.2V Babylon 655138201 “ u fl Ø X y [ X K v FB9902 655112301 “ u fl Ø X y [ X K v CL9301 2012 L9900 4.7uH C9902 Q9900 RSR25P03TL C9904 F9301 C9901 C9905 C9906...
Page 56
FBA - EG1H FE_RADD[0-14] FE_RADD[0-14] FE_RADD[15-19] 18/22 PWB LAYOUT NOTE: P l a c e f i t t e d s t r a p r e s i s t o r s i n g r o u p s STRAP SETTINGS o f 4 o r 8 t o a l l o w r e p l a c e m e n t b y r e s i s t o r a r r a y s d u r i n g l a t e r t r i a l...
Text Search ~ AE Printed Wiring Board Side A ~ J 1 0 0 3 J 1 0 0 2 C N 1 0 0 1 A 1 0 0 0 C N 1 3 0 2 C N 1 3 0 0 T U 1 9 0 0 C N 1 3 0 3 C N 2 1 0 0...
Page 69
Text Search ~ AE Printed Wiring Board Side B ~ W 1 9 1 I C 1 9 0 0 I C 1 2 5 0 I C 1 7 0 0 I C 1 1 0 8 I C 1 8 0 0 1 - 8 7 6 - 5 6 0 - 1 1 !d#E#P!]#G#W!c - 68 -...
Text Search ~ CB1 Printed Wiring Board ~ I C 9 7 1 0 3 . 1 5 A 2 4 V I C 9 1 0 0 F 9 1 0 0 I C 9 7 0 8 C N 9 7 0 0 I C 9 4 0 0 C N 9 7 0 3 C N 9 0 0 1...
Text Search ~ FBA Printed Wiring Board Side A ~ C N 5 5 0 0 I C 5 5 0 1 C N 7 5 0 0 A - 1 5 5 0 - 2 9 4 - A 1 - 8 7 7 - 3 2 9 - 1 1 C N 7 7 0 0 I C 5 4 0 3...
Page 73
Text Search ~ FBA Printed Wiring Board Side B ~ 1 - 8 7 7 - 3 2 9 - 1 1 F 5 4 0 0 F 3 . 1 5 A L 2 4 V I C 7 8 0 6 C N 7 5 0 1 I C 4 9 0 3 I C 4 9 0 1...
Text Search ~ G6 Printed Wiring Board Side A ~ C N 6 1 5 3 C N 6 5 0 5 A 6 0 0 5 I C 6 1 5 0 E T 6 0 0 0 C N 6 1 5 1 A - 1 5 4 8 - 0 8 9 - A C 6 5 2 9 C 6 3 0 2...
Page 75
Text Search ~ G6 Printed Wiring Board Side B ~ J L 6 5 2 6 E T 6 0 0 0 Q 6 4 0 0 J L 6 3 0 4 A 6 0 1 2 R 6 1 5 6 C 6 3 1 6 J R 6 0 1 9 A 6 0 0 5...
Text Search ~ GL Printed Wiring Board Side A ~ J W 6 7 8 0 J W 6 9 3 0 F B 6 7 8 F B 6 7 8 0 J W 6 9 3 1 J W 6 7 0 6 C 6 7 3 0 F B 6 7 8 1 J W 6 9 3 3...
Page 78
Text Search ~ GL Printed Wiring Board Side B ~ - 77 -...
SECTION 5 EXPLODED VIEWS NOTE : Non-serviceable items with no part number and no Items marked “*” are not stocked since they are seldom required for description are not stocked because they are not required for routine service. routine service. Some delay should The construction parts of an assembled part are indicated be anticipated when ordering these with a collation number in the remarks column.
....................131 Note: To ensure safety and reliability it is Sony policy that power supply boards should not be repaired at component level in the field as a result... The D4, G6, G7 and GL boards are regarded as non service...
Page 85
Note : The components identified by mark contain confidential information. Strictly follow the instructions when ever the components are repaired and/or replaced. REF.NO. PART.NO DESCRIPTION REMARK REF.NO. PART.NO DESCRIPTION REMARK * A-1557-695-A CB1 Board, Complete (55 inches only) C9155 1-112-777-11 CERAMIC CHIP 0.01UF C9156 1-112-777-11...