Table of Contents
Advertisement
1
N
i
iNSTRUCTioN MANUAl
FM CloCk RAdio
FUNCTioN ANd CoNTRolS
(see fig. 1)
1. <</Tune-
7. VoluME up/alarM 2 on/oFF
2. SET.MEM/MEMORY+
sEt
3. SNOOZE/SLEEP
8. BattErY coMpartMEnt
4. on/oFF
9. rating laBEl
5. >>/TUNE+
10. displaY
6. VOLUME DOWN/ALARM 1 ON/
11. spEakEr
oFF sEt
12. AC POWER CORD
13. FM antEnna
PoWER CoNNECTioN
Plug the AC power cord to a household outlet AC source. This unit is equipped
with a battery back up system, it requires a 1x3V CR2032 Flat Lithium battery
(Not included). Insert the battery in the battery compartment, making certain
that the positive and negative (+ and -) battery terminals are attached to the
corresponding terminals on the plate in the battery compartment. If an AC
power failure occurs, the clock automatically switches to the battery power
supply, the clock and timer memory continue running. When the AC power
resumes, the clock switches back to AC again.
TiME MANUAl SETTiNg
In standby mode, press and hold the SET.MEM/M+ button (2).
"24 Hr" will blink. Press the TUNE+ (5) or Tune- (1) button to set the hour format
between 12 hour (12 Hr) format and 24 Hour (24 Hr) format.
Press the SET.MEM/M+ button (2) and the hours will blink.
Press the Tune+ (5) or Tune- (1) to set the current hour.
Press the SET.MEM/M+ (2) button again then the minute digits will blink. Press
the TUNE+ (5) or Tune- (1) to set the current minutes.
Once setting done, press SET.MEM/M+ (2) button once again to indicate the
current time is set.
AlARM SETTiNg
Press the AL.1/AL.2 button (6/7) once to preview the alarm time.
The alarm time is displayed and will blink, press & hold the AL.1/AL.2 button
(6/7) for 3 seconds and the hours will blink.
Press the TUNE+ (5) or Tune- (1) to set the alarm hour.
Press the AL.1/AL.2 button (6/7) again; the minute digits will blink. Press the
TUNE+ (5) or Tune- (1) to set the alarm minutes.
Press the AL.1/AL.2 button (6/7) to set the alarm sound mode: Buzzer or Radio.
Press Tune + (5) or Tune – (1) to choose different volume. The alarm volume
will gradually increase. Then press the ALARM button when done.
To delay the alarm, press SNOOZE. It will come on again in approx. 9 minutes.
You may repeat this cycle several times during the alarm cycle. To stop the
alarm, press ALARM button .
To stop the alarm from coming on the following day, hold the ALARM button to
turn it off. The alarm icon will disappear to indicate the alarm is disarmed.
2
SNooZE FUNCTioN
When the alarm rings, press Snooze button (3) to suspend the alarm & to
activate the snooze function, Alarm will stop & will ring again 9 minutes later.
Press SNOOZE key again, alarm will be suspended again, another 9 minutes
later the alarm will ring again and so on until the next alarm rings.
Note: The Snooze interval time is 9 minutes.
- To turn the Snooze function off, press once on AL.1/AL.2 button (6/7).
- Press and hold the AL.1/AL.2 button (6/7). The alarm icon will disappear to
indicate the alarm is disabled.
RAdio ModE
Note: Ensure that the FM antenna is completely unrolled and extended to have
the best FM reception.
Press the ON/OFF button (4) to turn the unit on.
Use the TUNE+ (5) or Tune- (1) button to select the desired FM radio station. If
you press and hold the TUNE+ or Tune- button for 1-2 seconds, then release,
the unit will automatically scan to the next broadcasting station.
Press the ON/OFF button (4) to turn the radio OFF.
To SET/RECAll THE RAdio PRESETS
Press the ON/OFF button (4) to turn the unit ON.
Use the TUNE+ (5) or Tune- (1) button to select the desired FM station.
Press the SET.MEM/M+ button (2); "P02" will blink in the display.
Press the SET.MEM/M+ button (2) again to set the preset.
Repeat steps 2 through 4 to set more presets.
The unit can preset 10 stations totally for FM.
When "P01-P10" is blinking, press the Tune+ (5) or Tune- (1) button to select
the preset number.
When recalling preset stations, press SET.MEM/M+ button (2) to select the
preset number.
SlEEP oPERATioN
When listening to radio, press Snooze/Sleep button (3) to enter sleep mode.
You can just adjust the sleep timer from 90mins to 10mins by pressing the
Snooze/Sleep button (3). The unit will automatically turn off after the selected
time.
RESETTiNg
If the system does not respond or exhibits erratic or intermittent operation, you
may have experienced an electrostatic discharge (ESD) or a power surge that
triggered the internal microcontroller to shut down automatically. If this occurs,
simply disconnect the AC power cord and remove the system backup battery,
wait for at least 3 minutes and then setup the unit again as if it is a brand new
unit.
WARNiNg
1. No naked flame sources, such as lighted candles, should be placed on the
apparatus.
2. Do not place the product in closed bookcases or racks without proper
ventilation.
3
Advertisement
Table of Contents
