Terms and Conditions applying to all PACE Technologies Products 1. LIMITED WARRANTY AND DISCLAIMER: PACE Technologies Products are warranted for one year from the purchase date to be free from defects in material and workmanship under correct use, normal operating conditions, and proper application. PACE Technologies obligation under this warranty shall be limited to the repair or exchange, at PACE Technologies option, of any PACE Technologies Product or part which proves to be defective as provided herein.
Speed and Time Controller Water switch The NANO 1200T is a 12 or 14-inch single wheel grinding/ polishing machine for manual wet grinding or polishing of metallographic specimens. The NANO 1200T is a variable speed (0-1000 rpm) with three programmable fast speed buttons (approx.
Page 7
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 1.3 Mechanical Schematic Note: Installation of the NANO 1200T should be on a flat sturdy surface, with easy access to drain, water and electrical connections. 1.4 Features The NANO 1200T is equipped with a powerful motor, connected to the polishing wheel through a maintenance-free V-belt.
Page 9
2.3 Installation Install unit carefully! Improper installation voids warranty. The NANO 1200T should be placed on a flat stable surface. Connect to air, water supply, drain and electrical connections. After water, drain and electrical connections are completed, the system is ready for operation by activating the main power switch.
Securely hold the sample, preferably with two hands. 3.3 Emergency Statement The NANO 1200T polisher has been designed for polishing metallographic specimens up to 2- inch diameter. DO NOT GRIND OR POLISH oversize sample (greater then 1/3 diameter of working wheel. Always follow proper operational guidelines and avoid contact with moving parts, lubricants and abrasives.
Page 11
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 3.4 Safety Test Examine and verify that the NANO 1200T safety devices and operating performance are in good working condition prior to use. The following safety check is considered important: Emergency stop switch Emergency stop switch Activate main switch.
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 4.0 Start-up and Operation Water valve 4.1 General Working wheel The NANO 1200T is a hand grinding/ polishing machine. By adding the FEMTO power head, semi-automated polishing can be accomplished. 4.2 Control Panel...
Web: http://www.metallographic.com 5.0 Maintenance 5.1 Introduction The NANO 1200T requires very minimal maintenance. However, to increase the life of the polisher, it is suggested that the unit be rinsed after use. 5.2 Cleaning outside cabinet The cabinet should be cleaned occasionally with a moistened cloth. Do not use any chemicals or cleaning abrasives.
Error Message EOF a. Motor overheating a. Confirm proper voltage wiring set-up on motor. b. Reduce applied force during grinding a. Other errors a. Contact PACE Technologies for service Replace fuse Pry open fuse holder with small flat head screwdriver...
NANO 1200T Motor (1.5 hp) NANO 1000T/2000T PC board / frequency convertor (new machine using N1-008b 24V transformer) NANO 1200T PC board / frequency convertor (new machine using 24V N1-008c transformer) N1-008T PC board (top only) for 1 rpm increments...
Page 35
Description Images Mechanical Components NANO 1000T Single Wheel Belt N1-005 NANO 2000T Double Wheel Belt N2-005 NANO 1200T Single Wheel Belt N12-005 PTM-125-005 8-inch plain backed paper ring PTM-125-006 10-inch plain backed paper ring 12-inch plain backed paper ring PTM-225-005...