Terms and Conditions applying to all PACE Technologies Products 1. LIMITED WARRANTY AND DISCLAIMER: PACE Technologies Products are warranted for one year from the purchase date to be free from defects in material and workmanship under correct use, normal operating conditions, and proper application. PACE...
Water switch Speed display The NANO 2000T is a 8 or 10-inch single wheel grinding/ polishing machine for manual wet grinding or polishing of metallographic specimens. The NANO 2000T is a variable speed (0-1000 rpm) with three programmable fast speed buttons (approx.
Page 7
1.4 Features The NANO 2000T is equipped with a powerful motor, connected to the polishing wheel through a maintenance-free V-belt. Please read this instruction manual carefully and follow all installation, operating and safety guidelines.
Page 9
2.3 Installation Install unit carefully! Improper installation voids warranty. The NANO 2000T should be placed on a flat stable surface. Connect to air, water supply, drain and electrical connections. After water, drain and electrical connections are completed, the system is ready for operation by activating the main power switch.
Careful attention to this instruction manual and the recommended safety guidelines is essential for the safe operation of the NANO 2000T. Proper operator training is required for operation of the NANO 2000T. Any unauthorized mechanical and electrical change, as well as improper operation, voids all warranty claims.
Page 11
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 3.4 Safety Test Examine and verify that the NANO 2000T safety devices and operating performance are in good working condition prior to use. The following safety check is considered important: Emergency stop switch Emergency stop switch Activate main switch.
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 4.0 Start-up and Operation 4.1 General The NANO 2000T is a hand grinding/ polishing machine. By adding the FEMTO power head, semi-automated polishing can be accomplished. 4.2 Control Panel Water...
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 5.0 Maintenance 5.1 Introduction The NANO 2000T requires very minimal maintenance. However, to increase the life of the polisher, it is suggested that the unit be rinsed after use. Easy access to electronics with sliding rail design 5.2 Cleaning outside cabinet...
Error Message EOF a. Motor overheating a. Confirm proper voltage wiring set-up on motor. b. Reduce applied force during grinding a. Other errors a. Contact PACE Technologies for service Replace fuse Pry open fuse holder with small flat head screwdriver...
Page 35
3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com Part no. Description Images Mechanical Components NANO 1000T Single Wheel Belt N1-005 NANO 2000T Double Wheel Belt N2-005 NANO 1200T Single Wheel Belt N12-005 PTM-125-005 8-inch plain backed paper ring PTM-125-006 10-inch plain backed paper ring...
NSTRUCTION ANUAL 3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 9.0 Schematics (NANO 2000T case assembly) Please read this instruction manual carefully and follow all installation, operating and safety guidelines.
Page 45
NSTRUCTION ANUAL 3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 9.0 Schematics (NANO 2000T case assembly) Please read this instruction manual carefully and follow all installation, operating and safety guidelines.
Page 46
ANUAL 3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 9.1 Schematics (NANO 2000T internal mechanical assembly) Please read this instruction manual carefully and follow all installation, operating and safety guidelines.
Page 47
ANUAL 3601 E. 34th St. Tucson, AZ 85713 USA Tel. +1 520-882-6598 Fax +1 520-882-6599 email: pace@metallographic.com Web: http://www.metallographic.com 9.1 Schematics (NANO 2000T internal mechanical assembly) Please read this instruction manual carefully and follow all installation, operating and safety guidelines.