Related Manuals for GTE Adicos HOTSPOT Test Device HTL-2
Summary of Contents for GTE Adicos HOTSPOT Test Device HTL-2
- Page 1 HTL-2 IP40 Operating Manual HOTSPOT Test Device GTE Industrieelektronik GmbH | Helmholtzstr. 21, 38 – 40 41747 Viersen | Germany | +49 2162 3703-0 | info@gte.de...
- Page 2 41747 Viersen GERMANY Support hotline: +49 2162 3703-0 E-mail: support.adicos@gte.de © 2023 GTE Industrieelektronik GmbH – This document and all figures contained may not be copied, changed, or distributed without explicit approval by the manufacturer! Subject to technical changes! and GSME are registered trademarks of GTE Industrieelektronik GmbH.
- Page 3 SHORT DESCRIPTION Abstract The Advanced Discovery System (ADICOS ) is used for early detection of fires in industrial ® environments. It is comprised of various, separate detector units. By parameterizing and arranging the detectors appropriately, the system fulfills a predefined detection goal. The ADI- COS system ensures reliable early detection of embers and smoldering fires even in adverse environments.
-
Page 4: Table Of Contents
CONTENTS Inhaltsverzeichnis About this manual ..........Objective. -
Page 5: About This Manual
ABOUT THIS MANUAL About this manual Objective This manual describes the operation of the GSME test device ADICOS HTL-2. It is intended to be used only by properly qualified personnel (–› Chap. 2, Safety Instructions). Explanation of Symbols TThis manual follows a certain structure to make it easy to work with and understand. The following designations are used throughout. -
Page 6: Abbreviations
ABOUT THIS MANUAL WARNING! This combination of symbol and signal word indicates a possibly dangerous sit- uation which could lead to death or severe injuries if it is not avoided. CAUTION! This combination of symbol and signal word indicates a possibly dangerous sit- uation which could lead to minor injuries if it is not avoided. -
Page 7: Safety Instructions
SAfETy INSTrUCTIONS Safety Instructions To safely operate ADICOS HTL-2, you absolutely must read, understand, and follow these instructions and the safety information they contain in their entirety. WARNING! Fire and explosion hazard due to hot plate! The ADICOS HTL-2 uses a hotplate that can cause fires on contact with foreign bodies or explosions in explosion hazardous zones. -
Page 8: Personnel Qualification
SAfETy INSTrUCTIONS Personnel Qualification All work performed on ADICOS systems must be performed only by qualified staff. Qualified staff is considered to be persons who can perform tests on special fire detection systems and recognize possible dangers owing to their specialist training, knowledge, and experience and their knowledge of relevant provisions. -
Page 9: Scope Of Delivery
SCOpE Of DELIvEry Scope of Delivery Number Description Transport case HTL-2 test device ADICOS HTL-2 410-2410-008 EN21... -
Page 10: Construction And Function
CONSTrUCTION AND fUNCTION Construction and Function Overview Description HTL test tube HTL hot plate HTL holder HTL connection element for the battery baton of the test system solo Swivel joint HTL control panel Operating LED (green) ... -
Page 11: Function
CONSTrUCTION AND fUNCTION Function The ADICOS HTL-2, in combination with the solo battery pole from No Climb Products Ltd., enables convenient in-situ tests and functional verification of ADICOS HOTSPOT type infrared detectors in industrial plants. For this purpose, its heating plate is set to 95 ... 105 °C and is pressed against the optics of the HOTSPOT de- tector to be tested, thus homogeneously exciting the entire field of view of the detector sensor. -
Page 12: Preparation For Operation
prEpArATION fOr OpErATION Preparation for Operation Removing Dirt WARNING! Fire hazard due to deposits Deposits in the test tube of the ADICOS HTL-2 (e.g. carbon dust) can ignite during operation. • Clean the device before each use! Charging the Battery Baton Check battery status Before mounting the battery baton of the test system solo , check the charging... -
Page 13: Commissioning
COMMISSIONING Commissioning WARNING! Risk of fire due to active hot plate The ADICOS HTL-2 uses a hot surface and can cause fires and explosions if used improperly. • Operate the device only if you have a permit for hot work! •... -
Page 14: Detector Test
DETECTOr TEST Detector Test WARNING! Risk of injury due to falling deposits Deposits on the ADICOS detectors can drop when touched during testing and cause injury. • Wear appropriate protective clothing Preparing for the Detector Test Use ADICOS software to call up the detectors to be tested Open the thermal image of the detector Select the tab “Max.-Werte T”... -
Page 15: Malfunctions
MALfUNCTIONS Malfunctions Description of malfunction Possible cause Solution Operating LED and heating Batteries are empty Charge the solo battery baton LED do not light up (–› Chapter 5.2) Operating LED and heating Battery baton Remove the solo battery baton and LED do not light up improperly inserted connect it again (–›... -
Page 16: Storage
DISpOSAL Storage Store the device in its transport case when it is not in use. NOTE! Property damage due to improper use! An ADICOS HTL-2 that has not cooled down may cause property damage in the case due to the hot heating plate. •... -
Page 17: Id Plate
TECHNICAL DATA 11.1 ID Plate Model Device model SERIAL Serial number Year of production (variable) (variable) ART-Nr Article number TEMP Ambient Degree of (variable) temperature protection COM-Nr Communication Voltage range / Internal fusing number (variable) maximum pow- (Short-circuit er consumption current) (heating incl.) CE marking... - Page 18 NOTE 410-2410-008 EN21 ADICOS HTL-2...
- Page 19 NOTE ADICOS HTL-2 410-2410-008 EN21...