Related Manuals for GTE Adicos GTL-3
Summary of Contents for GTE Adicos GTL-3
- Page 1 GTL-3 Operation Manual GSME Test Device GTE Industrieelektronik GmbH | Helmholtzstr. 21, 38 – 40 41747 Viersen | Germany | +49 2162 3703-0 | info@gte.de...
- Page 2 Support hotline: +49 2162 3703-0 E-mail: support.adicos@gte.de © 2020 GTE Industrieelektronik GmbH – This document and all illustrations contained herein are protected by copyright and may not be copied and pasted, modified or distributed with- out the express consent of the manufacturer! Technical data is subject to change without notice! ADICOS®...
- Page 3 The ADICOS GTL-3 test device is used for all ADICOS GSME gas sensor detectors. It includes an adapter for the SOLO test system (detectortesters.com). It requires the battery baton as well as the telescope bars.
-
Page 4: Table Of Contents
Technical Data ..........17 430-2410-102 EN11 ADICOS GTL-3... -
Page 5: About This Manual
About this MAnuAl About this Manual Objective This manual describes the operation of the GSME test device ADICOS GTL-3. It is intended to be used only by properly qualified personnel (–› Chap. 2, For your Safety). Explanation of Symbols This manual follows a certain structure to make it easy to work with and understand. The fol- lowing designations are used throughout. -
Page 6: Abbreviations
Store this manual near the detectors, in a place where it can easily be accessed when needed for reference. Applicable documents Tips and recommendations Please refer to the operating instructions of the accessories from No Climb Products Ltd. (detectortesters.com). 430-2410-102 EN11 ADICOS GTL-3... -
Page 7: For Your Safety
• These instructions must be read and followed completely! Intended Use The ADICOS GTL-3 tester can only be used in combination with the SOLO battery bar from No Climb Products Ltd. (detectortesters.com). The test probe is designed for functional testing of ADICOS GSME fire gas detectors. The operating parameters described in (–›... -
Page 8: Qualification Required Of Personnel
The following accessories are available for the GTL-3 test device: Art.-Nr. Description 430-2402-105 SOLO Battery pole* 430-2402-106 SOLO Quick battery charger* 430-2403-105 SOLO Telescopic extension rod* 430-2403-072 GTL-3 Glow filter 430-2003-073 GTL-3 Smouldering sticks *Manufacturer: No Climb Products Ltd. 430-2410-102 EN11 ADICOS GTL-3... -
Page 9: Scope Of Delivery
Delivery Scope of Delivery Quan- Description tity Transport case GTL-3 housing with gas funnel GTL-3 fan unit Protection tube GTL-3 smouldering sticks (in tin can) GTL-3 glow filter (in tin can) Lighter ADICOS GTL-3 430-2410-102 EN11... -
Page 10: Structur And Funkction
AnD Function Structure and Function Overview GTL-3 Test Head 430-2410-102 EN11 ADICOS GTL-3... -
Page 11: Function
Operating switch Fan unit Function The ADICOS GTL-3 produces the typical fire gas mix- ture by buring of the GTL 3 smoouldering rod, which is located in a safe combustion tube. In connection with the SOLO battery pole, the fire gases are directed to the detectors in a controlled manner with aid of an electronic fan. -
Page 12: Preparation For Commissioning
For coMMissioning Preparation for commissioning NOTICE! The ADICOS GTL-3 tester works by means of controlled combustion, which can cause fires and explosions if used improperly. • Do not open the housing within hazardous areas Inserting the embers filter The GTL-3 glow filter prevents the escape of embers and hot ashes during operation. As soon as the filter is polluted and clogged with fire deposits, it must be replaced before next operation. -
Page 13: Insert Smouldering Sticks
Charging the battery bar Tips and recommendations Before each use check the battery condition with aid of the charger. • If necessary, recharge the batteries according to the manufacturer‘s in- structions (see operating manual Solo battery pole)! ADICOS GTL-3 430-2410-102 EN11... -
Page 14: Commissioning The Gtl-3 Test Device
Device Commissioning the GTL-3 test device NOTICE! The ADICOS GTL-3 tester works with controlled combustion, which can cause fires and explosions if used improperly. • Do not open the housing within hazardous areas • Only operate the unit when it is approved for hot work! •... -
Page 15: Mounting The Test Head
Secure assembled housing parts with knurled screw Commissioning the fan unit The fan unit of the ADICOS GTL-3 starts working as soon as it is connected to the SOLO bat- tery bar and the operating switch is pressed. Mounting the battery pole Insert the SOLO battery pole into the fan unit with the connection socket first. -
Page 16: Operation
Delete GTL-3 smouldering sticks Open the device Loosen knurled nut Remove glowing GTL-3 smouldering sticks carefully and extinguish with water Alternatively: Break off the glowing end of the GTL-3 smouldering rod generously and extinguish with water 430-2410-102 EN11 ADICOS GTL-3... -
Page 17: Maintenance
GTL-3 Clean housing If necessary, clean the outer surfaces of the GTL-3 housing with a damp cloth. NOTICE! Abrasive cleaning agents can damage the surface of the GTL-3 probe. • Do not use aggressive cleaning agents! ADICOS GTL-3 430-2410-102 EN11... -
Page 18: Storage
Store the device in the transport case when not in use. NOTICE! This device is operated by means of controlled combustion, which can lead to fires without initiated extinguishing. • Only insert the device into the case when the smolderinmg rod is extin- guished! 430-2410-102 EN11 ADICOS GTL-3... -
Page 19: Disposal
10 Technical Data General information Dimensions: 430 x 90 (L x Ø) Weight: 0,58 Electrical characteristics Power consumption: Input voltage: Environmental conditions Temperature range: °C +10 ... +45 Humidity range: < 95 (non condensing) ADICOS GTL-3 430-2410-102 EN11...