Advertisement
This product complies with Lot20 of the Energy Efficiency Directive (2015/1188)
Model Identifier(s):
Nominal heat output Pnom
Minimum heat
Pmin
output (indicative)
Maximum heat
Pmax,c
output
Auxiliary electricity consumption
At nominal heat
elmax,c
output
At minimum heat
elmin
output
In standby mode
elSB
Control options
Electronic room temperature
control plus week timer
With distance control option
General Information
The heater is designed for wall mounting using the wall bracket
supplied. It should only be operated when in the upright position
as shown (see Fig. 1). All models are splash proof to IP24. Before
connecting the heater check that the supply voltage is the same as
that stated on the heater.
Electrical Connection
WARNING: THIS APPLIANCE MUST BE EARTHED
WARNING:- The electrical installation of this heater must be carried out
by a suitably qualified or trained electrician, and be in strict accordance
with the current wiring Regulations BS 7671. The supply must be
connected via a switched fused spur with a fuse rated suitably for the
appliances flex. Failure to follow these instructions will mean that the
manufacturer's instructions have not been adhered to.
THERE ARE NO EXCEPTIONS.
Mains lead are coloured in accordance with the following code:
GREEN AND YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
The heater is fitted with a length of flexible cable type H05VV-F size
3 x 1.5mm2 models for connection to the fixed wiring of the premises
through a suitable connection box positioned adjacent to the heater.
A means for disconnection must be incorporated in the fixed wiring
of the premises in accordance with the current wiring regulations.
Products that are supplied without a plug are for installation into the
fixed wiring of the property, via a suitable double pole switched fused
spur with a fuse rated suitably for the appliances flex.
WARNING: This heater must not be connected to the electricity supply
via an external switching device.
Wall Mounting
IMPORTANT The wall bracket supplied with the heater must be
used and the heater must be installed in the correct orientation.
The fixings should be used to secure the bracket to the particular
wall on which the heater will be installed.
The heater should be positioned observing the minimum clearances
stated around the heater (see Fig. 2).
WARNING:
This product is heavy and care should be taken in installation
Energy Related Product Directive
DTD2R
DTD2R
DTD2R
05
07
10
500 W
750 W
1000 W
500 W
750 W
1000 W
500 W
750 W
1000 W
0
0
0
0
0
0
<0.0005
<0.0005
<0.0005
Yes
Yes
Yes
Yes
Yes
Yes
DTD2R
DTD4R
DTD4R
12
05
1250 W
500 W
750 W
1250 W
500 W
750 W
1250 W
500 W
750 W
0
0
0
0
<0.0005
<0.0005
<0.0005
Yes
Yes
Yes
Yes
Yes
Yes
Ensure minimum distances are maintained as shown in Fig. 2 below
Min.200mm
Min.
30mm
Wall Bracket Installation Steps:
STEP 1
10 cm
(3.94 in.)
10
1. Use the wall bracket as a measuring device to place the heater on the
wall.
2. Mark the location for the two bottom screws (A-A) and fasten the two
screws in the wall.
STEP 3
3. Place the wall bracket onto the bottom screws (A-A). Then fasten the wall
bracket with the top screws.
4. Place the heater on the wall bracket (1), secure the tilt strap (2) and click
the heater onto the top catches (3).
5. Once the heater has been connected through a suitable connection box
to the fixed wiring of the premises, the heater can be switched on (4).
DTD4R
DTD4R
07
10
15
1000 W
1500 W
1000 W
1500 W
1000 W
1500 W
0
0
0
0
0
0
<0.0005
<0.0005
Yes
Yes
Yes
Yes
Fig. 2
DT
Min.
50mm
Min.
30mm
Min 50mm
STEP 2
STEP 4
3
4
DTD4R
20
2000 W
2000 W
2000 W
0
0
<0.0005
Yes
Yes
2
1
Advertisement
