Nikon FTZ II - Mount Adapter Manual

Introduction

Before using this product, carefully read both this document and the documentation provided with the camera and lens.

• This mount adapter allows Nikon F mount NIKKOR lenses to be mounted on Nikon Z mount mirrorless cameras.
• This mount adapter cannot be mounted on Nikon F mount digital SLR cameras or 1 mount advanced cameras with interchangeable lenses (Nikon 1 cameras).
• This mount adapter cannot be used with NIKKOR 1 lenses.
• Update the camera firmware to the latest version. With earlier versions, the camera may fail to detect the lens or adapter correctly and some features may not be available. The latest version of the camera firmware can be the Nikon Download Center.
• Note that depending on the lens, the adapter may limit autofocus or other camera features. For more information, see Compatible F Mount Lenses, available from the Nikon Download Center.

Nikon Download Center
https://downloadcenter.nikonimglib.com/

For Your Safety

To prevent damage to property or injury to yourself or to others, read "For Your Safety" in its entirety before using this product.

After reading these safety instructions, keep them readily accessible for future reference.

Failure to observe the precautions marked with this icon could result in death or severe injury.

Failure to observe the precautions marked with this icon could result in injury or property damage.

• Do not disassemble or modify this product.
  Do not touch internal parts that become exposed as the result of a fall or other accident.
  Failure to observe these precautions could result in electric shock or other injury.
• Should you notice any abnormalities such as the product producing smoke, heat, or unusual odors, immediately disconnect the camera power source.
  Continued operation could result in fire, burns or other injury.
• 
  Keep dry.
  Do not handle with wet hands.
  Failure to observe these precautions could result in fire or electric shock.
• Do not use this product in the presence of flammable dust or gas such as propane, gasoline or aerosols.
  Failure to observe this precaution could result in explosion or fire.
• Keep this product out of reach of children.
  Failure to observe this precaution could result in injury or product malfunction. In addition, note that small parts constitute a choking hazard. Should a child swallow any part of this product, seek immediate medical attention.
• Do not handle with bare hands in locations exposed to extremely high or low temperatures.
  Failure to observe this precaution could result in burns or frostbite.

• Do not leave the product where it will be exposed to extremely high temperatures, for an extended period such as in an enclosed automobile or in direct sunlight.
  Failure to observe this precaution could result in fire or product malfunction.

Parts of the Adapter

Lens

1. Nikon F mount (attaches to lens)
2. Lens signal contacts
3. Lens mounting mark
4. Lens-release button

Camera Mount

5. Adapter mounting mark
6. Nikon Z mount (attaches to camera)
7. CPU contacts

Attachment and Removal

Turn the camera off before attaching the adapter to or removing it from the camera or attaching lenses to or removing lenses from the adapter. Choose a location out of direct sunlight and be careful to prevent dust from entering the devices. While attaching lenses, avoid pressing the camera or adapter lens-release button.

Attaching the Adapter and Lens

1. Remove the body and rear lens caps from the adapter and the body cap from the camera.
2. Attach the adapter to the camera.

• Keeping the adapter mounting mark aligned with the mounting mark on the camera body (a- ), position the adapter on the camera and then rotate it counterclockwise until it clicks into place (a- ).
  

3. Remove the rear lens cap.
4. Attach the lens to the adapter.

• Keeping the lens mounting mark aligned with the lens mounting mark on the adapter (b- ), position the lens on the adapter and then rotate it counterclockwise until it clicks into place (b- ).
  

Detaching the Lens and Adapter

1. Detach the lens.

• Press and hold the adapter lens-release button (a- ) while turning the lens clockwise (a- ).
• Attach the front and rear caps to the lens after removal.
  

2. Detach the adapter.

• Press and hold the camera lens-release button (b- ) while turning the adapter clockwise (b- ).
• After removing the adapter, attach the body and rear caps to the adapter and the body cap to the camera.
  

CPU Lenses with Aperture Rings
Select minimum aperture (the highest f/-number) before attaching CPU lenses equipped with aperture rings.

Incompatible Lenses and Accessories
The following lenses and accessories cannot be used. Attempting to forcibly attach any of this equipment could damage the adapter or the lens. Individual variation may render lenses other than those listed below incompatible; do not use force if you encounter resistance when attempting to attach a lens.

• Non-AI lenses
• IX-NIKKOR
• TC-16A AF Teleconverter
• Lenses that require the AU-1 focusing unit (400mm f/4.5, 600mm f/5.6, 800mm f/8, 1200mm f/11)
• Fisheye (6mm f/5.6, 7.5mm f/5.6, 8mm f/8, OP 10mm f/5.6)
• 2.1cm f/4
• K2 Extension Ring
• 180–600mm f/8 ED (serial numbers 174041–174180)
• 360–1200mm f/11 ED (serial numbers 174031–174127)
• 200–600mm f/9.5 (serial numbers 280001–300490)
• AF lenses for the F3AF (AF 80mm f/2.8, AF 200mm f/3.5 ED, TC-16 AF Teleconverter)
• PC 28mm f/4 (serial number 180900 or earlier)
• PC 35mm f/2.8 (serial numbers 851001–906200)
• PC 35mm f/3.5 (old type)
• Reflex 1000mm f/6.3 (old type)
• NIKKOR-H Auto 2.8cm f/3.5 (28mm f/3.5) lenses with serial numbers below 362000
• NIKKOR-S Auto 3.5cm f/2.8 (35mm f/2.8) lenses with serial numbers below 928000
• NIKKOR-S Auto 5cm f/2 (50mm f/2)
• NIKKOR-Q Auto 13.5cm f/3.5 (135mm f/3.5) lenses with serial numbers below 753000
• Micro-NIKKOR 5.5cm f/3.5
• Medical-NIKKOR Auto 200mm f/5.6
• Auto NIKKOR Telephoto-Zoom 85–250mm f/4–4.5
• Auto NIKKOR Telephoto-Zoom 200–600mm f/9.5–10.5

Using the Mount Adapter

• Autofocus may not function as expected when the adapter is used with an F mount NIKKOR lens. If the camera has trouble focusing, set the AF-area mode to single point and select the center focus area, or focus manually.
• With some lenses, the camera vibration reduction feature may not function as expected or may cause vignetting or a drop in peripheral illumination.

Precautions for Use

• When using the adapter with lenses weighing over 1300 g (2 lb 13.9 oz), support the lens when holding the camera and do not use the camera strap. Failure to observe these precautions could damage the camera lens mount.
• Keep the CPU and lens signal contacts clean.
• Do not leave the adapter in humid locations or in locations in which it may be ex-posed to moisture. Rusting of the internal mechanism can cause irreparable damage.
• Do not leave the adapter next to open flames or in other extremely hot locations.
  Extreme heat could damage or warp the adapter.

Caring for the Adapter

• Do not touch the interior of the mount adapter. Use a blower or soft brush to remove dust, being careful not to rub or scratch the inside of the adapter.
• When cleaning the adapter, use a blower to remove dust and lint and then wipe the adapter gently with a soft, dry cloth.
• Never use organic solvents such as paint thinner or benzene to clean the adapter.
• Do not store with naphtha or camphor moth balls or in direct sunlight. If the adapter will not be used for an extended period, store it in a cool, dry location to prevent mold and rust.

Accessories

Supplied Accessories

• BF-1B Body Cap
• LF-N1 Lens Cap (rear cap)

Specifications

Nikon reserves the right to change the appearance, specifications, and performance of this product at any time and without prior notice.

Documents / Resources

References

• index.html

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Nikon FTZ II - Mount Adapter Manual