NateoSante EOLIS 600 Operating Manual page 22

How do I replace the pre-filter?
1 • Turn off your unit.
2 • Open the front cover and remove the filter block using the 2 tabs designed for this purpose.
3 • Remove the used pre-filter from the filter block to replace it with a new one.
4 • Put the filter block back in, with tabs facing out.
5 • Close the front cover. Make sure the front cover is positioned correctly, to ensure that your unit will
operate correctly.
6 • Turn on the unit. The new filter block is tested by the "filter block test" system. "New filter block?":
You can say NO (only for changing built-in filters).
When should I replace the filter block?
The lifespan of the filter block depends on how the unit is used and the concentration of pollutants in
the air (between 8 and 12 months if the unit operates 24/7). For an instant status of your filter block'
conditions, see the real filter service indicator (see p. 19). It is sometimes necessary to replace the filter
after it has been used for de-pollution after construction or prolonged use in a very polluted environment
(thick smoke, strong persistent odours, etc.)
Do not clean the filter, place it in water or vacuum it: this could cause changes in the fibres or cartridges,
leading to poor operation or reduced efficiency of your EOLIS Air Manager.
If the alert icon
You will receive an alert when your filter block are 80% clogged. Depending on the use level of your filter
block, your unit will alert you as follows:
• 80% used filter block: "Plan to change filter block (leave the device switched on during replacement
and confirm the message before closing the front cover) "
• 100% used filter block: " Pending filter block change (leave the device switched on during replacement and
confirm the message before closing the front cover) "
If the filter block reaches 100% saturation, the unit will stop working to prevent damage to the motor. It
will start working again as soon as you have changed the filter block.
How do I replace the filter block?
1 • DO NOT TURN OFF YOUR UNIT.
2 • Open the front cover and remove the filter block using the 2 tabs designed for this purpose.
3 • Remove the new filter block from their packaging, making sure not to damage them.
4 • Put the filter block back in, with tabs facing out.
5 • The message "New filter block?" appears: you can press YES. If the front cover is open but you have
not changed the filter block, you can press NO or ignore the message.
6 • Close the front cover. Make sure the front cover is put in place correctly, to ensure that your unit will
operate properly. The new filter block are tested by the "filter block test" system.
Replacing UV-C lamps
When should I replace the UV-C lamps?
The UV-C lamps will wear differently depending on how often you activate the UV-C LAMP (or photocatalysis)
feature. The lifespan for a UV-C lamp is generally 1 to 2 years.
How do I replace the UV-C lamps?
1 • Turn off your unit.
2 • Open the front cover and remove the filter block to reach the UV-C lamps.
3 • To remove or replace a lamp, pull it gently and vertically upwards.
4 • Remove the new lamps from their packaging taking care not to damage them and place them in the
unit where the old lamps were.
5 • Then put the filter block back in, with tabs facing out.
6 • Close the front cover. Make sure the front cover is positioned correctly, to ensure that your unit will
operate correctly. Your
Cleaning the EOLIS Air Manager
Clean your unit with a soft cloth that is slightly damp to remove dust. Make sure to follow the safety
instructions (see p.16).
Cleaning the sensors
Your EOLIS Air Manager has 2 sensors: one particle sensor and one VOC (Volatile Organic Compounds)
sensor. These 2 sensors measure air quality in real time. For optimal operation, it is necessary to clean
EN EN
22 - EOLIS Air Manager 600 600S 1200 1200S 22 - EOLIS Air Manager 600 600S 1200 1200S
appears on the control screen, a message indicating the advanced use status will appear.
EOLIS Air Manager
is ready to operate again.