Front Panel Control Details - Cambridge Audio 840A v2 Manual

Cambridge Audio Azur 840A v2 Amplifier
Front panel controls
Standby / On Phones Speaker A/B Mode
1 2 3 4
Standby/On
1
Switches the unit between Standby mode (indicated by dim power LED)
and On (indicated by bright power LED). Standby is a low power mode
where the power consumption is less than 10 Watts. The unit should be
left in Standby mode when not in use.
Note: As default the 840A V2 ramps the volume up or down when
switched on and when going into Standby mode. This feature can be
turned off if desired; please refer to the 'Amplifier setup' section of this
manual for more information.
Phones
2
Allows for the connection of stereo headphones with a ¼" Jack plug.
Headphones with an impedance of between 32 and 600 ohms are
recommended. When the headphones are connected, the loudspeaker
relays are released switching off the output to the loudspeakers
(speakers A and B).
Speaker A/B
3
Press to scroll through the speaker sets connected to the loudspeaker
terminals on the back panel (speaker sets A, B or A and B). This can be
used for listening to an extra set of loudspeakers in another room.
Please note that care should be taken when choosing speakers if two
loudspeakers are going to be used on each channel. If the combined
resistance measured on the loudspeaker terminals is too low the
amplifier may not switch out of Standby mode until a suitable load
resistance is detected. For more information refer to the CAP5 section of
this manual.
Note: When using one pair of speakers, use speakers with a nominal
impedance of between 4-8 ohms. When using two pairs of speakers,
use speakers with a nominal impedance of between 6-8 ohms each.
4 Mode
Press to switch between Volume and Balance modes. Press and hold to
to enter the 840A V2 System Configure menu.
Infrared sensor
5
Receives IR commands from the supplied Azur remote control. A clear
unobstructed line of sight between the remote control and the sensor is
required.
& Input select buttons
6 7
Push the appropriate input selection button to select the source
component that you wish to listen to (highlighted by a solid circle on the
display). The signal selected is also fed to the Tape Out sockets so that
it may be recorded. The input should not be changed whilst recording
(but the recorded signal can be checked using the tape input Tape
Monitor).
8
6
5

Front Panel Control Details

Bass Treble
7
9
Display
8
LCD used to control the 840A V2. Please refer to the 'Operating
instructions' and 'Amplifier setup' section of this manual for more
information.
Bass and Treble
9
Press to release and rotate to allow subtle adjustments to the tonal
balance of the sound.
Direct
10
This control gives the audio signal a more direct path to the power
amplifier stage of your amplifier, bypassing the tone control circuits for
the purest possible sound quality.
The Bass/Treble icon ( ) appears in the display when the bass and
treble circuit is active (in circuit) and is not present when they are
bypassed.
Note: Direct can be set on or off individually for each input. This settting
is recalled each time a source is selected.
Volume
11
Use to increase/decrease the level of the sound from the outputs of the
amplifier. This control affects the level of the loudspeaker output, the
pre-amp output and the headphone output. It does not affect the Tape
Out connections.
As the 840A V2 uses a very high quality passive resistor ladder switched
by relays to achieve volume and balance, audible control clicks can be
heard from the unit when the volume or balance is adjusted.
The Volume control is also used in navigating the 840A V2 System
Configure menus on the front panel display.
Please refer to the 'Operating instructions' section of this
manual for more information on some functions of these
buttons.
azur 840A
Class XD Integrated Amplifier
11
Direct
10
Volume
4