Simply Automated SimplySmart Series Getting Started
  1. Manuals
  2. Brands
  3. Simply Automated Manuals
  4. Home Automation
  5. SimplySmart Series
  6. Getting started

Simply Automated SimplySmart Series Getting Started

Lamp (dimmer) module accessory for models uml7 and uml8
Hide thumbs Also See for SimplySmart Series:
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

Getting Started
Lamp (Dimmer) Module Accessory
For Models UML7 and UML8
Model UML7
Model UML8
TM
Simply Automated Pre-Configured SimplySmart
Series
TM
Utilizes SimplySmart
technology to make installation a breeze.
No computer programming required!
Simple-n-easy, ready to use lighting control.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SimplySmart Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Simply Automated SimplySmart Series

Summary of Contents for Simply Automated SimplySmart Series

  • Page 1 Getting Started Lamp (Dimmer) Module Accessory For Models UML7 and UML8 Model UML7 Model UML8 Simply Automated Pre-Configured SimplySmart Series Utilizes SimplySmart technology to make installation a breeze. No computer programming required! Simple-n-easy, ready to use lighting control.
  • Page 2 Getting Started Lamp (Dimmer) Module Accessory For Models UML7 and UML8 Simply Automated Pre-Configured SimplySmart Series Utilizes SimplySmart technology to make installation a breeze. No computer programming required! Simple-n-easy, ready to use lighting control. IMPORTANT SAFETY INSTRUCTIONS When using electrical products, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
  • Page 3 The indicator above button 1 will continuously blink green for five minutes. To exit the programming mode, quickly tap the button two times. Important Note: To change the dimming level for a lamp module, refer to Section 3.c. Simply Automated, Incorporated 6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA Technical Support: www.simply-automated.com...
  • Page 4 • Test the button 1 scene by pressing button 1 one time to activate the scene and tapping two-times to deactivate the scene. Simply Automated, Incorporated 6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA Technical Support: www.simply-automated.com or 800-630-9234 452-0112-0203 Rev.
  • Page 5 You have created a new scene by re- programming button 3 from the previously pre-set dimming level. Simply Automated, Incorporated 6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA Technical Support: www.simply-automated.com...
  • Page 6 All the pre-configured kits and accessories can be edited and added to scenes as previously described – only limitation being not more than one of each model number or kit number per installation. One touch button convenience to turn ON/OFF up to ten or more Simply Automated devices – custom scenes you create!
  • Page 7 Plug-In Inverting Phase Coupler, fits a standard (NEMA 10-50) 240VAC / 50Amp clothes dryer type outlet ZPCI-W Wire-in Inverting Phase Coupler ZPCI-B Breaker Panel Inverting Phase Coupler Simply Automated, Incorporated 6108 Avenida Encinas, Suite B, Carlsbad, CA 92011 USA Technical Support: www.simply-automated.com or 800-630-9234 452-0112-0203 Rev. C Revised: September 14, 2011...
  • Page 8 Network ID #: The default Network ID # setting for the Pre-Configured Series is 250. This information is needed when using the Scheduler-Timer. Section 6: Simply Automated Custom Expansion Series Powerful Custom Expansion Capability – up to 250 devices – using your PC and UPStart software! Devices include single rocker dimmers, deluxe dimmers with different faceplates (up to 8 buttons), lamp or appliance modules, tabletop pedestal with 8 buttons, wall receptacle, fixture relay, fixture dimmer or scheduler-timer.

This manual is also suitable for:

Simplysmarttm uml7Simplysmarttm uml8

Table of Contents