DAB PUMPS ACTIVE DRIVER M/M 1.1 Manual page 3

GENERAL INDEX
1. GENERAL
2. WARNINGS
2.1 Skilled personnel
2.2 Safety
2.3 Responsibility
2.4 Particular warnings
3. APPLICATIONS
4. TECHNICAL DATA AND LIMITATIONS OF USE
5. ELECTRICAL CONNECTIONS OF THE A.D. TO THE ELECTROPUMP
6. CONNECTION TO THE POWER SUPPLY LINE
7. HYDRAULIC CONNECTIONS
7.4 Risk of frost
8. CHARACTERISTICS – INTERPRETATIONS – OPERATION
8.1 Characteristics and interpretations
8.2 Operation: keyboard factory settings
8.3 First switch-on operations (only with A.D. as accessory)
8.4 Operation: Parameters for the user (MODE and SET keys for 2 seconds)
8.4.1 SP: Setting the setpoint pressure (in bar)
8.5 Operation: Parameters for the installer (MODE and SET and - keys for 5 seconds)
8.5.1 rC: Setting the rated current of the electropump (excluding A.D. M/M 1.1)
8.5.2 rt: Setting the direction of rotation (excluding A.D. M/M 1.1)
8.5.3 Fn: Setting the rated frequency (pre-set value 50Hz)
8.5.4 od: Setting the operating mode of the A.D.
8.5.5 rP: Setting the fall in pressure for restarting
8.5.6 Ad: Setting the interconnection address (excluding A.D. M/M 1.1)
8.5.7 Eb: Enabling booster (pre-set value 2) (excluding A.D. M/M 1.1)
8.6 Operation: Technical Assistance displays and settings
(MODE and SET and + keys for 5 seconds)
8.6.1 tb: Setting the reaction time of the water lack blockage
8.6.2 GP: Setting the gain of the proportional coefficient of the PI
8.6.3 GI: Setting the gain of the integral coefficient of the PI
8.6.4 FS : Setting the maximum rotation frequency of the electropump.
8.6.5 FL : Setting the minimum frequency
8.6.6 Ft: Setting the low flow rate threshold
8.6.7 CM: Method of exchange (pre-set value 1) (excluding A.D. M/M 1.1)
8.6.8 AE : Enabling the anti-block/anti-frost function
8.6.9 Setting pump start
8.6.10 SF : Setting the starting frequency
8.6.11 St : Setting the starting time
8.6.12 Setup of the auxiliary digital inputs IN1; IN2; IN3 with the parameters i1; i2; i3
(excluding A.D. M/M 1.1 and A.D. M/T 1.0)
8.6.13 Active Driver M/T 2.2 = setting the set point P1 function of input 2
8.6.14 O1: setting output 1 function (active alarm)(excluding A.D. M/M 1.1 and A.D. M/T 1.0)
O2: setting output 2 function (pump operating)(excluding A.D. M/M 1.1 and A.D. M/T
1.0)
9. DISPLAYS
9.1 Displays of the main values (MODE key)
Fr: Display of the current rotation frequency (Hz)
UP: Display of pressure (in bar)
C1: Display of electropump phase current (A)
UE: Display of the version of the software with which the appliance is equipped
9.2 Monitor display (SET and - key for 2 seconds)
UF: Display of flow
ZF: Display of zero flow
FM: Display of the maximum rotation frequency (Hz)
(excluding A.D. M/M 1.1 and A.D. M/T 1.0)
ENGLISH
37
page
39
39
39
39
39
39
39
40
40
40
41
41
41
41
44
44
45
45
45
45
45
45
45
46
46
46
46
46
46
47
47
47
47
47
48
48
48
48
48
49
49
49
49
49
49
49
49
49
49
49
49