Advertisement
troubleshooting process. The function of each LED is
described in the table below:
LED
Indicate Description
The device is powering on or the
ON
device is abnormal.
RUN
Blinking
The device is running normally
The device is powered off or the
OFF
device is abnormal.
ON
Wireless network is enabled
Wireless network is in an active
Blinking
WLAN(5T)
network status
Wireless network is running
OFF
abnormally or disabled
The
wireless
ON
established bridge and the signal
is great
0.5Hz blinking, the established
WLAN(2T)
bridge signal is normal; 1Hz
RSSI(5T)
Blinking
blinking, and the established
bridge signal is weak
The wireless terminal has not
OFF
established bridge
Ethernet port has established a
ON
valid network connection
WAN/
Ethernet port
Blinking
LAN1-
network status
LAN4
Ethernet
OFF
established
connection
Serial port is sending/receiving
Blinking
data
SERIAL
No serial port connection or no
OFF
data transfer
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device's configuration interface via IE
browser is shown as below:
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Enter device's IP address in the address bar of the
computer browser.
Enter device's username and password in the login
window as shown below.
terminal
has
Click "Login" button to login to the WEB interface of
the device.
Note:
is in an active
The default IP address of the device is "192.168.1.254".
The default user name and password of the device are
port
has
not
"admin".
valid
network
If the user name or password is lost, user can restore it to
factory settings via RESET button or management
software; all modified configurations will be cleared after
restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Antenna
2.4G/5G
dual-band
antenna
interfaces, RP-SMA-K(Female)
- 5 / 6 -
Wan
10/100Base-T(X) RJ45 interface
Lan
10/100Base-T(X) RJ45 interface
Serial Port
RS-232/485/422 serial port adopts
DB9 (Male);
RS-232/485 serial port adopt 2*5PIN
3.81mm pitch terminal blocks (serial
port occupies 6 pins)
Indicator
Running indicator, WLAN indicator,
RSSI indicator, WAN indicator, LAN
indicator, serial port indicator
Radio Frequency
Channel
802.11b/g/n: 2.412GHz~2.4835GHz
802.11a/n: 5.18GHz~5.825GHz
RF
Power
20dBm
Output
Modulation
DBPSK, DQPSK, CCK, OFDM, 16-
Scheme
QAM, 64-QAM
Receiving Sensitivity
802.11b
-95dBm@1Mbps, -89dBm@11Mbps
802.11g
-90dBm@6Mbps, -74dBm@54Mbps
802.11a
-89dBm@6Mbps, -72dBm@54Mbps
802.11n
-85dBm@MCS0, -67dBm@MCS7
Transmitting Power
802.11b
23dBm@1Mbps, 20dBm@11Mbps
802.11g/a
23dBm@6Mbps, 20dBm@54Mbps
802.11n
23dBm@MCS0, 20dBm@MCS7
Power Supply
Input
Power
12~36VDC,
support
Supply
connection
Access
Model I, Model II:
Terminal Block
3-pin 5.08mm pitch terminal block;
Model III, Model IV:
2*5PIN 3.81mm pitch terminal blocks,
power supply occupies 4 pins
Power Consumption
Model I
No-load at normal temperature:
2.0W@12VDC, 2.0W@36VDC
Full load at normal temperature:
anti-reverse
Advertisement
