Advertisement
On the wall of device mounting, place the device on
the wall for reference or refer to the mounting
dimension to mark two screw positions.
Nail M3 screws on the wall and keep 2mm
interspace reserved.
Hang the device on two screws and slide downward,
then tighten the screw to enhance stability,
mounting ends.
【Device Disassembling】
Power off the device.
Unscrew the screw on the wall about 2mm.
Lift the device upward slightly; take out the device,
disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug, then
remove the wiring section of terminal block. Please pay
attention to the above operation sequence.
【Power Supply Connection】
Model I, Model II
The Model I and Model II device of this
series provide 3-pin 5.08mm pitch
terminal blocks and supports 1 DC
power supply input which supports anti-reverse connection.
Pin definitions are shown in the left figure, V+ and V- are the
positive and negative poles of power input, and
grounding. Voltage range: 12~36VDC.
Model III, Model IV
This Model III and Model IV device of
this series provide 2*5PIN 3.81mm
pitch terminal blocks, power supply
occupies the left 4 pins. Support 1 DC
power supply input with anti-reverse
connection protection. The pins are defined as shown in the
figure on the left. V+ and V- are the positive and negative poles
of power input, and any set of V+ and V- can be used for power
input. Voltage range: 12~36VDC.
【Serial Port Connection】
Model I, Model II
The Model I and Model II device of this
series provide 1 RS-232/485/422 3IN1
serial port, and the interface type is DB9
male. The pin definition as follows:
PIN
1
2
3
RS-232
RXD
TXD
—
RS-485
D+
—
—
RS-485/422
RX-
RX+
TX+
PIN
6
7
8
- 4 / 6 -
IO (Reserved)
Model III, Model IV
PIN
Definition
Description
PIN
Definition
is the case
Description
【RESET Button Setting】
This series device provide 1 RESET button, press
the button for 1-3s then release it, then the 2T device
can enable debugging WLAN temporarily, and the 5T device
can be rebooted automatically; press the button for 5s then
release it to restore factory defaults. The SSID of debugging
WLAN, that is, the Wi-Fi name is ADMIN-XXXXXX(X is the last
six digits of the MAC address of the device), which is
password-free, and is mainly used to temporarily access the
device through the wireless network for debugging. After the
device restarts or reconfigures the wireless, the device will
automatically turn off the debugging WLAN.
【Antenna Connection】
Model I and model III of this series of device are equipped with
two antennas as standard, and the antenna specifications are
as follows:
Type
4
5
2.4/5.8G Dual frequency
GND
antenna
—
D-
GND
【Checking LED Indicator】
TX-
GND
The series of devices provide LED indicators to monitor its
9
operating
status,
DO+
DO-
DI+
DI-
Model III and IV of this series of
device provide 1 RS-232/485 2-in-1
serial port. The interface type is
2*5PIN 3.81mm pitch terminal, and
the serial port occupies 6 pins on the
right. The pin definition as follows:
1
2
3
4
5
V+
V-
D-
D+
GND
12~36VDC
RS-485 serial port
power input
6
7
8
9
10
V+
V-
TXD
RXD
GND
12~36VDC
RS-232 serial port
power input
Gain
Count
P/N
(dBi)
(pcs)
3005040132
2
2
which
has
simplified
the
overall
Advertisement
