Never allow a load attached to the trolley to swing or spin unintentionally. Never work under suspended loads. www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 2 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...
2. Function/Operation The Tiger TP/TG Trolley can be used to suspend a lifting appliance or load and allow it to traverse along a beam. The TP is the plain trolley model which is moved along the beam by hand. The TG is the geared trolley model which is moved along the beam by turning the hand chain.
Page 5
Over-tightening of the hand wheel will cause the worm gear to lock and will be difficult to release. Trolley with optional locking device www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 4 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...
In the case of a trolley in-situ, examine the beam to which the trolley is attached for any distortion. In the event of any defects refer the trolley to a Tiger distributor or Competent Person for thorough examination. Inspect the supporting structure for visual defects, e.g. deformations, damage, cracks, wear and corrosion marks. Check the runway track/beam is level, has an even running surface and is fitted with positive end stops which engage with the trolley frame or wheel treads.
TG geared trolley models are supplied with a hand chain operated gear. Inspection of the hand chain must be included in any inspection of the TG trolley. If the unit’s hand chain has been supplied with a Tiger Hand Chain Joiner link, make sure that it has been fitted correctly and is in good working order.
Declaration of Conformity Tiger TP/TG Trolleys have a 5:1 factor of safety. They are tested in line with the requirements within applicable sections of the European standard EN 13157: 2004+A1:2009 and the Australian standard AS1418.2. All items comply with the essential health and safety requirements of the Machinery Directive 2006/42/EC.
Lubricate exposed trolley drive pinion and wheel teeth. Hand chain not installed properly (twisted or Remove hand chain and re-install. kinked). www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 8 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...
The Company will return repaired or replacement products at The Company’s expense, but if it is determined there is no defect, or that the defect resulted from causes not within the scope of Tiger Lifting’s warranty, then the Customer must bear the cost of storing and retrieving the product.
A beam flange thickness up to 50mm can be accommodated if required – please ask for more information. # Please contact us for track widths outside of these ranges. Single Bar Twin Bar www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 10 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...
Page 12
Twin Bar Trolley 20.0t – 30.0t Due to our policy of continual product development, dimensions, weights and specifications may change without prior notice. www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 11 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...
Inspection Log Test Certificate/DOC Number Model Number Product Description Date introduced into service Serial Number Date Comments Signature www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 13 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...
Page 15
Owner’s Notes www.tigerlifting.com Unit 1, Greensfield Industrial Estate, Page 14 of 14 Willowburn Avenue, Instruction Guide Tiger TP-TG En 201812 v1.1 ALNWICK, NE66 2DG...