Summary of Contents for Advantage SENTRA SR Series
Page 1
I.O.M. #196 updated : 03/29/2023 INSTRUCTION MANUAL • INSTALLATION • OPERATION • MAINTENANCE Models with T300 Control Instrument ADVANTAGE ENGINEERING, INC. 525 East Stop 18 Road Greenwood, IN 46142 317-887-0729 fax: 317-881-1277 Model: Service Department fax: 317-885-8683 www.AdvantageEngineering.com Serial Number :...
Page 3
INSTRUCTION MANUAL SENTRA SR Series with T300 Control Instrument COVERING INSTALLATION OPERATION MAINTENANCE ADVANTAGE ENGINEERING, INC. 525 East Stop 18 Road Greenwood, IN 46142 317-887-0729 fax: 317-881-1277 Service Department fax: 317-885-8683 www.AdvantageEngineering.com E-mail: sales@AdvantageEngineering.com...
Heater Replacement Cooling Valve Service Voltage Change Pressure Switch Service Electronic Instrument Repair Policy And Procedure COMPONENTS Mechanical system Electrical system Page: 4 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
SPI Commands Communications Cable Optional Alarm Operation Parts : #119 Pump Modbus TCP Register Definitions for T Control Instruments Page: 5 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Temperature Control Units : Sentra with T300 Control Instrument GENERAL Receiving Instructions Introduction Safety Water Treatment Components Page: 7 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Observe all warning and safety placards applied to the unit. Failure to observe all warnings can result in serious injury or death to the operator and severe mechanical damage to the unit. Page: 8 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Alerts the user to possible explosive danger. Alerts the user to a hot surface danger due to high operating temperatures. CAUTION Page: 9 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
It is recommended that the services of a qualified water treatment specialist be engaged to determine what water treatment is required. Advantage assumes no responsibility for equipment failures which result from untreated or improperly treated water. Do not use deionized water in this unit. Some customized units may be compatible with deionized water.
Page 11
(2” on units up to 3 hp & 16 kW, 3” on larger units) Selection of certain options and features may change the size, look and configuration of the unit. Contact the factory for more information. Page: 11 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Temperature Control Units : Sentra with T300 Control Instrument INSTALLATION General To and From Process Connections Water Supply Connection Drain Connection Electrical Connection Page: 13 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
If installed, all such devices must be open and clean during unit operation. Page: 14 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
The temperature difference between the unit set point and the cooling water temperature The cooling valve position Consult factory when selecting the correct cooling valve for your application. Page: 15 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Some units may be customized and include a factory supplied power disconnect switch and/or higher specification electrical enclosure. Electrical power supply requirements are identified on the equipment data tag. Verify that available Page: 16 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 17
Make certain no moisture or standing water is present inside the electrical cabinet. Page: 17 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 18
Terminal Strip Power Entry Transformer Fuse Blocks Pump Motor Controller Control Transformer Heater Contactor Low Water Pressure Switch Typical Electrical Panel Page: 18 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 19
Temperature Control Units : Sentra with T300 Control Instrument Page: 19 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 20
Terminal Strip Power Entry Transformer Fuse Blocks Pump Motor Controller Control Transformer Heater Contactor Low Water Pressure Switch Typical Electrical Panel Page: 20 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Instrument Operation : Features Setup Instrument Operation : Machine Setup Instrument Operation : Tools and Status Shut Down Sequence Page: 21 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
All air must be purged before the unit is engaged for process temperature control. The automatic stat-up vent parameters are adjustable. See Section 3.5.F for more information. Page: 22 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 23
WARNING: Electrical power is engaged and caution should be employed while the cabinet is open. Page: 23 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 24
Process Flow Adjustments The operator must determine and set proper water flow rate for the most efficient and trouble free operation. Page: 24 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 25
Locate the motor name plate on the pump motor housing. The full load amp rating for the motor is listed on the name plate. Page: 25 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 26
From Process lines, install a bypass line between the two tees with a throttling valve. Adjust the valve for a minimum of 10 GPM. Page: 26 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
These Alerts prevent the unit from starting or operating and must be corrected immediately. • Water Pressure • Motor Overload • High Temperature Page: 27 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 28
310°F. This switch is installed in the To Process thermocouple. If a high temperature condition exists, the unit must first cool down before the high temperature limit switch can automatically reset. Page: 28 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 29
Power icon is pressed. The Pump Seal Cooling feature is explained elsewhere in this manual. Page: 29 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 30
Pump Overlaod From Process Probe Setpoint High Temperature Limit °F Manual Vent << Back Showing the screen advance to Manual Vent. Page: 30 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 31
To Process Setup Setup °F °F Cooling Heating 100% Setpoint Setpoint °F °F Showing the Icons for Heating and Cooling. Page: 31 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Delay Machine Second Setpoint Machine Configuration Configuration Enable Second Setpoint Deviation Second Setpoint Delay Cancel Cancel << Cancel << Page: 33 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 34
Select Yes or No. The selection donut will indicate the selection. Press OK to save the selection. Press Cancel to cancel the selection. Page: 34 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Units Basic Setup Basic Setup Language / Idioma Units English / Ingéls Imperial Spanish / Español Metric Cancel Cancel Page: 35 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 36
The factory default is Yes. Pump Seal Cooling Temp. Select the temperature the unit will cool to when Pump Seal Cooling is enabled. Page: 36 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Low Deviation Remote Remote Interface Autovent Flow Valve Size Autovent Setpoint Setpoint Showing screen advance to the Machine Setup screen. Page: 37 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 38
Machine Setup screen without saving the new value. The factory default is No. The mold purge option is typically factory installed and this value is preselected Page: 38 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
A Red light indicates the item is in a stop or error condition. Refer to the troubleshooting section for more information on items that have caused a stop or error condition. Page: 39 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 40
Showing screen advance to the Supply Water Pressure screen. The unit will not operate without adequate water supply pressure. Sufficient water supply pressure must be present to close the water pressure switch. Page: 40 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 41
°F attempt to Manual Vent << Back << Back restart. Showing screen advance to the High Temperature Limit screen. Page: 41 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
If any residual pressure is evident open the pressure relief valve to dissipate. Page: 42 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 43
Remaining process water can be discharged by removing the pump casing drain plug. Follow all lock out tag out requirements. Page: 43 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Unit will not start (Display is not Illuminated) Unit will not start (Display Illuminated) Unit Stops Unit Overheats Unit Underheats Pressure Relief Valve Leaks Page: 45 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
With the main power supply “on”, the unit will be prevented from starting by the following conditions: Water supply pressure inadequate. The display shows a red Alarm Shutdown Page: 46 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
The operator must service the cooling valve and remove any loose debris. Massive debris or scale deposits may necessitate replacement of the internal valve. Page: 47 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
However, in the case where the instrument is determined to be defective, the operator contact the Service Department for information. The instrument is not a field serviceable component. Page: 48 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
If this is the case, the operator must determine why the system internal pressure is excessive and correct the condition. Page: 49 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Pump Seal Replacement Heater Replacement Cooling Valve Service Voltage Change Pressure Switch Service Electronic Instrument Repair Policy & Procedure Page: 51 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Locate and remove the dust cap from the motor to expose slotted motor shaft. Pump casing bolts Page: 52 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 53
Seal components restart the unit. In many cases, a new pump seal will experience a small amount of leakage for a short Page: 53 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 54
Seal components Figure 5.1I Stationary member Figure 5.1J Rotating member Figure 5.1K Aligning impeller and Figure 5.1L spring Page: 54 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Set new heater into tank. Aligning the bolt pattern of the heater and tank flanges. Remove heater Page: 55 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 56
Replace the junction box cover and the lift-off cover panel. When complete, restart the unit. Page: 56 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Note the arrangement of the core spring and core assembly, diaphragm spring and diaphragm assembly. (See diagram.) Page: 57 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 58
Temperature Control Units : Sentra with T300 Control Instrument Coil and solenoid base sub assembly Valve body Core spring Core Body Diaphragm Diaphragm assembly assembly Gasket spring Page: 58 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
VOLTAGE CHANGE Some units can undergo a field voltage conversion by qualified technicians. Consult with the Advantage Service Department to determine if your unit can be converted. Have your Serial Number ready and call 317-887-0729. Typical Conversions for 1/2 to 7.5 horsepower motors and 10 to 16 kW heaters:...
Page 60
Wiring schematics for 240 and 480 volt heaters Revised 4/11 Wiring Schematic for Tempco Brand Heaters : 10 kw & 16 kW Page: 60 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 61
2.5 of this manual. Restart unit operations according to section 3 of this manual. Motor Starter and Overload Block Page: 61 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Install the brass elbow fitting. Teflon tape and leak preventative paste should be used to prevent water leakage. Install the capillary tube and resume operations. Page: 62 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Temperature Control Units : Sentra with T300 Control Instrument ELECTRONIC INSTRUMENT REPAIR POLICY AND PROCEDURE All control instruments used in Advantage temperature control units are covered by the machine’s warranty. Proprietary ‘tailor made’ instrument are manufactured specifically for Advantage. IN WARRANTY SERVICE INCIDENT Call the factory for diagnostic assistance.
Temperature Control Units : Sentra with T300 Control Instrument COMPONENTS Mechanical System Electrical System Page: 65 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
The valve can be manually activated by lifting the actuating lever. VALVE. The AVT valve is a patented Advantage design using a motor/gearbox assembly to open in minute increments from 0 to 100% a custom ball valve assembly. The AVT valve is controlled by custom programming of the instrument.
Standard models with 24kW and 34kW heaters are not supplied with a power cord and the customer must provide a 3 conductor with 1 ground wire sized for the unit. Page: 67 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 69
Physical : Cabinet Style for Units with 5 & 7.5 HP Pumps Regulator / Bypass Dual Zone Dolly Stacking Rack Page: 69 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Temperature Control Units : Sentra with T300 Control Instrument PHYSICAL : Cabinet Style for Units up to 16 kW Heaters and Pumps to 3 HP Page: 70 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Temperature Control Units : Sentra with T300 Control Instrument PHYSICAL : Cabinet Style for Units with: 24 & 34 kW Heaters and Pumps to 3 HP Page: 71 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Temperature Control Units : Sentra with T300 Control Instrument PHYSICAL : Cabinet Style for Units with : 5 & 7½ HP Pumps Page: 72 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
DUAL ZONE DOLLY Molders often need to run different temperatures on each mold half to produce the best quality part. Advantage can provide a dual zone dolly that holds two standard single zone temperature control units to meet this need.
Temperature Control Units : Sentra with T300 Control Instrument STACKING RACK Page: 75 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 77
SPI Commands Communication Cable Optional Alarm Operation Parts : #119 Pump Modbus TCP Register Definitions for T Control Instruments Page: 77 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 78
90 = 90 GPM @ 5 Horsepower 100 = 100 GPM @ 7 1/2 Horsepower Maximum Temperature Blank = 250°F 300 = 300°F Page: 78 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 79
∆ P values. This spike is called “water hammer”. Page: 79 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 80
Opens to purge water to drain WATER SUPPLY CONNECTION Valve must be closed during mold purge operation Typical mold purge. DRAIN CONNECTION Page: 80 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 81
The remaining pressure will be equal to the compressed air pressure used for the purge process. Use caution because disconnecting process lines under pressure incorrectly may cause injury. Page: 81 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277...
Page 82
There are many acceptable ways used to ‘set’ the device address and data rate. ADVANTAGE equipment provides access to the information via the front panel operators and displays. Other manufacturers may use internal DIP switches or jumpers.
Page 83
20 32 High alarm deviation 20 34 Low alarm deviation 20 40 Status process 20 70 To process temperature Page: 83 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 84
Molding Machine or PC Molding Machine or PC Molding Machine or PC SPI Master SPI Auxiliary SPI Auxiliary SPI Auxiliary Page: 84 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 85
Note: This Jumper Plug Must Be Inserted in All Unused Primary Machine Connectors 3rd COND Figure 8.5C Figure 8.5D Page: 85 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 86
Incorrect 3Ø power entry Pump overload tripped High temperature fault Water supply pressure fault Temperature deviation AVT valve malfunction Sensor probe malfunction Page: 86 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...
Page 87
Adapter, SS304, J56, 5/8" SEal, with Stls plugs 3301135X GAsket, Case, Buna 3444445 137.003.072 Pump Seal Ceramic #50458 64910000 101.000.327 Page: 87 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683 www.AdvantageEngineering.com...
Page 88
Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Alarm Machine Ack. ON / OFF Page: 88 Advantage Engineering, Inc. 525 East Stop 18 Road Greenwood, Indiana 46142 317-887-0729 Fax: 317-881-1277 Service Department Fax: 317-885-8683www.AdvantageEngineering.com...