Page 2
About this manual This manual describes how to install the Soluna EOS-5K Pack battery. Please read this manual carefully before you start to install the product, and follow the instructions throughout the installation process. If you are not sure about any of the requirements, recommendations, or safety procedures described in this manual, please contact Soluna immediately for advice and clarification.
1 Safety precautions 1.1 Warning Signs Warning signs are used to warn you about the conditions that may cause severe injury or damage to the device. They instruct you to exercise caution to prevent danger. The following table describes the warning signs used in this manual. Sign Description This battery pack contains high voltage which can cause electric shock...
Failure to observe the precautions described in this section can cause serious injury to persons or damage to property, observe the following precautions 1.2.1 Risks of explosion ● Do not subject the battery pack to strong impacts. Do not crush or puncture the battery pack. ●...
● Do not use cleaning solvents to clean the battery pack. 1.4 Response to emergency situations The Soluna EOS-5K Pack battery pack comprises multiple batteries that are designed to prevent hazards resulting from failures. However, SOLUNA cannot guarantee their absolute safety.
If the battery pack seems to be damaged, pack it in its original container, and then return it to SOLUNA or your distributor. Damaged batteries may leak electrolyte or produce flammable gas. If you suspect such damage, immediately contact SOLUNA for advice and information. 1.5 Qualified installers This manual and the tasks and procedures described herein are intended for use by skilled workers only.
2 Product Introduction Soluna EOS-5K Pack is an LiFePO4 lithium battery product with BMS (battery management system). It is a battery module with CAN communication, under-voltage, over-voltage, over-current, over-temperature, under-temperature protection functions. It has the characteristics of high energy density, long life, safety and reliability and so on, and It is your trustworthy green environmental product.
Cycle life @ 25℃ (under standard charge and discharge ≥6000 conditions,charge 0.2C,discharge 0.2C) Contactor DC Disconnect Fuse Warranty Please refer to SOLUNA WARRANTY CONDITIONS <3W (work), Power consumption <100mW (sleep) System Voltage System Current Monitoring parameters Cell Voltage Cell temperature...
Page 11
System Configuration Module parallel 1~12 Parallel Operating Conditions Indoor Installation Location Outdoor Operating Temperature -10~50 ℃ Operating Temperature 15~30 ℃ (Recommended) Storage Temperature -20~60 ℃ Humidity 5%~95% Altitude Max. 2,000 m Cooling Strategy Natural Convection Reliability & Certification Cell:UL1642 Certificates Battery Pack:CE、RoHS、...
2.5 Appearance ① ② ③ ⑤ ④ Number Name Remark Logo ① Cable connection interface ② Power ON/OFF switch ③ Battery capacity & Status indicator light ④ Hand ⑤ 12 / 29...
2.6 Connection port User can see the connections port of Soluna EOS-5K Pack after the cover plat is opened, Please find the following pictures for details. ① Details ⑧ ⑦ ⑥ ⑤ ② ③ ④ ⑨ Number Name Remark Cover plat ①...
CAN2 port For inverter communication ⑥ CAN1 dial switch These DIP switches are used for the ⑦ connection of multiple batteries CAN2 dial switch These DIP switches are used for the ⑧ connection of multiple batteries Remote port Power switch of BMS power supply ⑨...
Push button switch------The white light will be on after pressing the button. b. Status indicator light------light is always on if there is no alarm, the light will blink if the Soluna EOS-5K Pack has any warning. 15 / 29...
3 Installation The battery pack is too heavy for one to carry. Make sure that two or more persons are moving the battery pack together. 3.1Unpacking the package 3.1.1 Cut the packing tape and open the carton,and remove the EPE foam. 3.1.2 Pull out the battery pack, and remove the Scaleboard、PE bag、Carton、...
Charging cables ● Network cable 3.4 Installation location We recommend that Soluna EOS-5K Pack is used in Soluna Home energy storage systems, if not, please Make sure that the installation location meets the following conditions: ● The building is designed to withstand earthquakes.
● The location is far away from the sea, to avoid salt water and humidity. ● The floor is flat and level. ● There are no flammable or explosive materials nearby. ● The ambient temperature is between 15 and 30°C. ●...
Name Insulated gloves Safety goggles Safety shoes 3.7 Wiring specification In order to standardize the wiring specification of Soluna EOS-5K Pack, the following requirements are required for connecting wires of Soluna EOS-5K Pack. Battery wire Communication cable Remote wire It is recommended to use It is recommended to use 26 mm²...
3.8 Installation method The following three methods are recommended for Soluna EOS 5K Pack, 3.8.1 Wall hanging Mounting Step 1) Open the expansion screw holes on the wall (the size of the opening hole is shown below) Step 2) Mount the bracket to the wall with expansion screws.
Page 21
3.8.2 Floor mounting Step 1) Fix the bracket on the product with 4 PCS M6 screws. (Diagram as shown below) Step 2) To open expansion screw holes on the floor. Step 3) Fix the product on the floor with another 4pcs M6 screws. 21 / 29...
Page 22
3.8.3 Cabinet Mounting Step 1) Fix the U-box accessories to the product with 4pcs M6 countersunk head screws. (Diagram as shown below) Step 2) Install the product inside of cabinet, make sure the mounting hole sizes are as below. 22 / 29...
1)The “2” on the DIP switch of the first battery CAN2 port should be turned to the “ON” position. 4.2 Multiple units are connected to the inverter, Please find the following diagram for details. Soluna EOS-5K Pack 12 Soluna EOS-5K Pack 6 Soluna EOS-5K Pack 1 CAN2...
5.1 Way 1 (Factory default ) Connect with pin2 & pin3 with metal connector first, then press the Metal button switch, the Soluna EOS-5K Pack will start to work within 25 seconds, it will stopped to output if there has no communications after 5 minutes 5.2 Way 2...
LCD/LED for firmware reversion. inverter 2) Battery firmware is not Please use canbus tool box or Soluna Update battery's firmware. matching with inverter manufacture. smart energy cloud to check firmware reversion.
Page 27
Plug the communication port resistor or missing or wrong dial redial. 4) Battery firmware is not the latest. Please use canbus tool box or Soluna Update the firmware to the latest. smart energy cloud to check firmware reversion. 27 / 29...
Page 28
Please read the SOP of wifi setting up. 3) System establish failed due to S/N valid. APP will remind. Contact with Soluna for further action. Minor Alarm message on 1) Battery reach to 1st level alarm such as No need further action.
We hope that this user manual has clearly demonstrated the product. If you still have any doubts or something not clear about it in the specifications, feel free contact to us please. we will do our best to support you! SOLUNA (Shanghai) Co., Ltd Add: No.3492 Jinqian Road, Shanghai, China 201406 Tel: +86-21-57475835 Email: sales@solunabattery.com...
Need help?
Do you have a question about the EOS-5KPack and is the answer not in the manual?
Questions and answers