Advertisement
Quick Links
Required Tools
Wheelbarrow
Shovel
Digging Bar or Pick
Allen Wrench (Provided)
Ladder
Level
PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING
*Before digging, please obey local laws by notifying your local utilities marking
1. Select an area in your yard that is reasonably level and meets the space requirement
for your equipment. Ground Space: 18' x 15'. Play Space: 22' x 24'.
2. Please refer to the top rail assembly sheet and assemble your top rail as instructed.
3. Position the top rail (see top rail assembly page) about 10' from the selected spot
where you want the unit to finally stand. Using a tape measure and marker, mark
location of the swing hangers and the ladder along the top rail. (see top view on
assembly and installation instructions for measurements.)
4. Assemble swing hangers (see swing hanger assembly sheet) and attach securely to
the top rail.
5. Using the hammer, install the plug into the open end of the top rail.
6. Locate position in your yard where the upright ladder will stand. Dig the hole for the
ladder (see Installation Instructions page #1). Lay the ladder onto the ground with
the bottom of the ladder laying just over the hole where it will finally stand. Hint: Be
sure to situate the ladder so that when the unit is finally standing the rungs will be
facing as desired in your space.
7. Turn the top rail onto its side on the ground. Slide the outrigger into the sleeve at
the top of the ladder and position it to the marks previously made. (see Installation
Instructions page #3). Loosely install set screws into the top of the ladder sleeve.
Bolt "A" frame legs into place (see installation instructions page #2).
8. Using two strong adults, stand the swing frame up, allowing the ladder to fall into
the hole previously dug. (Note: set will not be level at this point.) At this point,
check to make sure that the top rail is still in its proper place inside the ladder top
sleeve. Adjust as necessary by holding onto the ladder securely and pushing or
pulling the "A" frame section causing the outrigger to slide inside the top sleeve.
When you are satisfied that the top rail is in the proper position, securely tighten the
set screws in the top sleeve of the ladder.
Installation Instructions
MT40
Hammer or Mallet
Open End or Box Wrenches: 5/8", 9/16", ¾"
Ratchet Handle & Sockets: 5/8", 9/16", ¾", 17mm
Marker Pen
Tape Measure
Cordless/Electric Drill w/ the Following Bits: Phillips, 3/8"
organization*
Advertisement
Related Manuals for Component Playgrounds Monkey Tree Swing Set w/Slide and Turning Bar
Summary of Contents for Component Playgrounds Monkey Tree Swing Set w/Slide and Turning Bar
- Page 1 Installation Instructions MT40 Required Tools Wheelbarrow Hammer or Mallet Shovel Open End or Box Wrenches: 5/8”, 9/16”, ¾” Digging Bar or Pick Ratchet Handle & Sockets: 5/8”, 9/16”, ¾”, 17mm Allen Wrench (Provided) Marker Pen Ladder Tape Measure Level Cordless/Electric Drill w/ the Following Bits: Phillips, 3/8” PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING *Before digging, please obey local laws by notifying your local utilities marking organization*...
- Page 2 9. With the ladder still standing in its hole, situate the “A” frame end to the desired position in the play area. Determine location of the “A” frame legs and mark the holes. Move the legs out of the way and dig the holes. (Keep most of the hole to the inside of the leg).
- Page 3 Top Rail Assembly Step 1: Slide the undrilled end of the longer Top Rail as far as it will go into the Sleeve of the Triple End. Step 2: Slide the Swing Hangers and tighten onto the Top Rail during the Top Rail Assembly process.
- Page 4 Two piece Top Rail Assembly Step 3: Step 2: Step 1: *Make sure to line up the set screws so they make a straight line as show in the graphic above.
- Page 5 Model MT40 GROUND SPACE 19’ X 15’ MINIMUM RESIDENTIAL PLAY SPACE 23’ X 24’...
-
Page 6: Installation Instructions
Model MT40 Continued Installation Instructions #1 Hole Sizes for Cementing in the Set (C) Fire Pole & (A) Upright Ladder (B) A Frame Legs Turning Bar 20” 28” 24” 12” 18” Holes 12” x 12” Holes 28”x20”x24” Holes 18” wide x 12” deep (Approx. - Page 7 Note: We recommend you check the pendulum in the swing hangers at least every 6 months for normal wear.
- Page 8 Installation Instructions MT Turning Bar and Fire Pole add on Turning Bar MT Fire Pole (Approximately one 80 lb. bag of concrete mix) • Determine Desired Location of Fire Pole on the Top Rail, or the Turning Bar on the Upright Ladder Leg. •...
- Page 9 RAVE/ROCKET SLIDE MOUNTING INSTRUCTIONS 1. Attach the slide bracket to the upright ladder by placing the carriage bolt through the ladder and through the holes in the bracket. Then secure Slide Bracket with the flate washer, loc washer, and hex nut. SHOWN ON RIGHT.
-
Page 10: Read Before Use
While every attempt is made by Component Playgrounds to ensure the highest degree of safety in all of our equipment, we cannot guarantee freedom from injury. The user assumes all risk of injury due to use. - Page 11 We hope that you and your family will enjoy many of hours of great family fun while using your Component Playgrounds Products. We appreciate your business. Our goal is to provide safe, durable and fun products using the best materials available. Your product should be mostly maintenance free.
- Page 12 (“spray paint”) at most hardware stores and at Component Playgrounds.) 5. Plastic Lumber Platforms: If you have purchased a structure which includes a platform, the plastic lumber does not need to be finished or stained. It is 100% maintenance free.
- Page 13 To Help Prevent Injuries from Falls & Other Hazards 1. Never attach, or allow children to attach the following items to your swing set: Ropes, jump ropes, clotheslines, pet leashes or any similar type of item to your swing set. Any item such as these may present a strangulation hazard.
- Page 14 Residential Products Limited Lifetime Warranty Component Playgrounds works to build heavy duty products that will stand up to the heavy use of active children. You can trust Component Playgrounds because of the way we design and build our products. We make products that are simple to own, and easy to maintain. This adds up to the best value on playground products that you can count on, and that kids will play on time after time.
- Page 15 Return this form via e-mail to: Contact Person:_____________________________________ sales@componentplaygrounds.com Address:___________________________________________ Or via U.S. mail to: City: ____________________State:______Zip:_________ Component Playgrounds Phone: ____________________________________________ 1630 North Beck Street Purchase Date: __________Completion Date: ____________ Salt Lake City, UT 84116 SALES REPRESENTATIVE/DEALER INFORMATION Today’s Date:_____________________________________...
Need help?
Do you have a question about the Monkey Tree Swing Set w/Slide and Turning Bar and is the answer not in the manual?
Questions and answers