Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TYAN FT72-B7015-LE
Summary of Contents for TYAN FT72-B7015-LE
- Page 1 ® TYAN FT72 B7015-LE Service Engineer’s Manual http://www.tyan.com...
- Page 2 http://www.tyan.com...
- Page 3 Corporation and has been reviewed for accuracy and reliability prior to ® printing. TYAN assumes no liability whatsoever, and disclaims any express ® or implied warranty, relating to sale and/or use of TYAN products including liability or warranties relating to fitness for a particular purpose or ® merchantability. TYAN retains the right to make changes to produce descriptions and/or specifications at any time, without notice.
- Page 4 There will be danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by manufacturer. Dispose of used battery according to manufacturer instructions and in accordance with your local regulations. http://www.tyan.com...
- Page 5 About this Manual This manual provides you with instructions on installing your FT72-B7015-LE. This Manual is intended for experienced users and integrators with hardware knowledge of personal computers. This manual is consisted of the following parts: Chapter1: Provides an introduction to the FT72-B7015-LE...
- Page 6 SAFETY INFORMATION Before installing and using FT72-B7015-LE, take note of the following precautions: ·Read all instructions carefully. ·Do not place the unit on an unstable surface, cart, or stand. ·Do not block the slots and opening on the unit, which are provided for ventilation.
-
Page 7: Table Of Contents
Table of Contents Chapter 1: Overview ..............9 1.1 About the TYAN FT72-B7015-LE..........9 1.2 Product Models..............10 1.3 Features ................11 1.4 Standard Parts List ..............13 1.4.1 Box Contents ..............13 1.4.2 Accessories ..............15 1.5 About the Product..............16 1.5.1 System Front View ............16 1.5.2 System Rear View ............16... - Page 8 M1008 LED Control Board Connector Pin Definition ...55 Replacing the System Fan ..........56 3.7.1 replacing the rubber screws .........57 Appendix I: Redundant Power Behavior ........61 Appendix II: Cable Connection Tables ........63 Appendix III: FRU Parts Table ............65 Appendix IV: Technical Support ..........67 http://www.tyan.com...
-
Page 9: Chapter 1: Overview
IT environment but also offers a smooth path for future application usage. FT72-B7015-LE uses rack-mountable 4U chassis featuring a robust structure and a solid mechanical enclosure. All of this provides FT72-B7015-LE the power and flexibility to meet the needs of nearly any server application. http://www.tyan.com... -
Page 10: Product Models
With (4) 2400W(2+1) B7015F72V2R-LE-N429 internal 2.5” NVIDIA M2090 PWR supply SATAII HDD Support (2) With (3) 2400W(2+1) B7015F72V2R-LE-N3275 internal 2.5” NVIDIA M2075 PWR supply SATAII HDD Support (2) With (4) 2400W(2+1) B7015F72V2R-LE-N4275 internal 2.5” NVIDIA M2075 PWR supply SATAII HDD http://www.tyan.com... -
Page 11: Features
1.3 Features TYAN FT72B7015-LE (B7015F72V2-LE) Form Factor 4U Rackmount Chassis Model FT72 Dimension (D x W x 27.96" x 17.245" x 6.93" (710 x 438 x 176mm) System Motherboard S7015 Board Dimension 16"x19" (406.4x482.6mm) Gross Weight 32KG Buttons (1) PWR / (1) RST / (1) NMI / (1) ID... - Page 12 Temp. Environment In/Non-operating 90%, non-condensing at 35° C Humidity RoHS RoHS 6/6 Complaint Yes Barebone (1) F72-B7015 Barebone Package Manual (1) BB User's manual Contains Installation CD (1) TYAN installation CD Heatsink / Cooler (2) CHSK-0410, 1366-pin CPU heatsinks http://www.tyan.com...
-
Page 13: Standard Parts List
(8) CCBL-146I, 2*4pin PWR cable for GPU card (8) CCBL-146H,2*3pin PWR cable for GPU card 1.4 Standard Parts List This section describes FT72-B7015-LE package contents and accessories. Open the box carefully and ensure that all components are present and undamaged. The product should arrive packaged as illustrated below. - Page 14 120 x120 x38 MM Fan M1008 Front LED control Board(R02) M7015 Rear I/O Board M7015-PBP PWR Backplane Board(R01) M7015-PDB PWR Distribution board for PCI-E card(R02) http://www.tyan.com...
-
Page 15: Accessories
If any items are missing or appear damaged, contract your retailer or ® browse to TYAN ’s website for service: http://www.tyan.com. ® The Web site also provides information on other TYAN products, plus FAQs, compatibility lists, BIOS settings, and more. ® 1 x TYAN... -
Page 16: About The Product
The following views show you the product. 1.5.1 System Front View USB ports ID button Power button (with LED) Warning LED NMI button HDD LED Reset button 1.5.2 System Rear View ID LED VGA Port Expansion slots Power Supply Share BMC LAN Port USB Port http://www.tyan.com... -
Page 17: Led Definitions
ID LED will show the system is identified with emitting blue light. Users from remote site could also activate ID LED by input a few commands in IPMI, detailed software support please visit http://www.tyan.com for latest AST 2050 user guide. -
Page 18: Motherboard Layout
1.5.4 Motherboard Layout S7015GM4NR-LE The diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. http://www.tyan.com... -
Page 19: Jumpers & Connectors
Board-to-Board Receptacle connector CN19 USB header CN43 Front Panel header CN36/CN37/CN40 FAN connector CN101 Clear CMOS CN61 System Intrusion header CN73 NMI button header CN74 ID button header CN10 SATA5 CN11 SATA4 CN12 SATA3 CN13 SATA2 CN14 SATA1 CN15 SATA0 http://www.tyan.com... - Page 20 Jumper Placement CN40 CN43 CN19 CN37 CN36 CN18 CN43: Front Panel header Signal PW_LED+ PW_LED- WLED+ HDD_LED+ PWR_SW# P3V3_SB RST_SW# Pin_1 http://www.tyan.com...
- Page 21 USB1- BLUE USB1+ HSYNC USB2- VSYNC USB2+ DDC_DATA USB3- DDC_CLK USB3+ Vcc5_VGA Vcc_USB Vcc_USB Vcc_USB Vcc_USB Vcc_USB Vcc_USB CN19: USB header Signal VCC_USB USB6- USB6+ VCC_USB USB7- USB7+ Pin_1 CN36/ CN37/ CN40: FAN connector Signal P12V TACH PWM P12V http://www.tyan.com...
- Page 22 (default setting) 3. Use jumper cap to close Pin_2 and Pin_3 for several seconds to Clear CMOS Pin_3 Pin_1 4. Put jumper cap back to Pin_1 and Pin_2 Clear CMOS (default setting) 5. Reconnect power and power on system http://www.tyan.com...
- Page 23 CN61: System Intrusion header Pin_1 Signal INTRUDER_N CN73: NMI button header Pin_1 Signal FP_NMI_N CN74: ID button header Pin_1 Signal ID_BUTTON_N http://www.tyan.com...
-
Page 24: System Block Diagram
1.5.6 System Block Diagram S7015GM4NR-LE Block Diagram http://www.tyan.com... -
Page 25: Internal View
1.5.7 Internal View M1008 M7015 -PDB Front LED control Board PWR Distribution board M7015 -PBP 2.5” HDD Bracket PWR Backplane Board System Fan Power Cage CPU Sockets Expansion Slots S7015GM4NR-LE Memory Slots Motherboard http://www.tyan.com... - Page 26 -N329/N3275 (With Three GPU cards) -N429/N4275 (With Four GPU cards) http://www.tyan.com...
-
Page 27: Chapter 2: Setting Up
Most of the electrical and mechanical connections can be disconnected using your fingers. It is recommended that you do not use needle nosed pliers to remove connectors as these can damage the soft metal or plastic parts of the connectors. http://www.tyan.com... -
Page 28: Precautions
Working on a system that is connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid damage to FT72-B7015-LE or injury to yourself. Ground yourself properly before removing the top cover of the system. -
Page 29: Installing Motherboard Components
CPUs, memory modules and add on cards. 2.1.1 Removing the Chassis Cover Follow these instructions to remove FT72-B7015-LE chassis cover. Thumb two screws on the back side as show in the small diagram. Then slide the top cover out. -
Page 30: Installing The Cpu And Heatsink
2.1.2 Installing the CPU and Heatsink Follow the steps below on installing CPUs and CPU heatsinks. Locate the CPU socket. Remove the PnP cap from the CPU socket. http://www.tyan.com... - Page 31 Lift the load lever in the direction of the arrow until the load plate is completely lifted. Position the CPU over the socket, ensuring that the gold triangle is on the bottom-left corner of the socket, and then fit the socket alignment keys into the CPU notches. http://www.tyan.com...
- Page 32 Place the heatsink on top of the CPU and secure it with 4 screws. For the safest method of installation and information on choosing the appropriate heat sink, using heat sinks ® ® validated by Intel . Please refer to Intel s website at www.Intel.com http://www.tyan.com...
-
Page 33: Installing The Memory
Press the memory slot locking levers in the direction of the arrows as shown in the following illustration. Align the memory module with the slot. When inserted properly, the memory slot locking levers lock automatically onto the indentations at the ends of the module. http://www.tyan.com... - Page 34 2). Refer to the memory population option table for recommended memory installation instruction. 3). “√”indicates a populated DIMM slot. Memory Population Option Table ® To achieve the best performance, TYAN strongly recommended memory installation configuration as listed below: Single CPU installed (CPU0 Only) Quantity of memory...
- Page 35 CPU1 DIMMA 1 √ √ CPU1 DIMMA 2 √ CPU1 DIMMB 0 √ √ √ CPU1 DIMMB 1 √ √ CPU1 DIMMB 2 √ CPU1 DIMMC 0 √ √ √ CPU1 DIMMC 1 √ √ CPU1 DIMMC 2 √ http://www.tyan.com...
-
Page 36: Installing Expansion Cards
2.1.4 Installing Expansion Cards FT72-B7015-LE has expansion slots which can support GPU (Graphic Processing Unit) card. Follow these instructions to install expansion cards. 1. Locate the expansion slot on the motherboard, unscrew the bracket from the slot you want to use. - Page 37 3. Insert the card into the slot and secure it with the screws you removed from the bracket. 4．Installing the PCIE-Extender to fix add on card immovable. http://www.tyan.com...
- Page 38 5. Connect the cables between the expansion card and the power distribution board, the connectors you use should match with the slot you add the card with. http://www.tyan.com...
- Page 39 6. Retighten the bracket to make add on card stable. 7. Here is the last step to install the air duct. http://www.tyan.com...
-
Page 40: Installing Hard Drives
2.1.5 Installing Hard Drives The FT72-B7015-LE supports two internal 2.5” SATAII hard disks. Follow these instructions to install a hard drive. Unscrew the 2.5’’ bracket out from the chassis, place a 2.5’’ hard drive into the HDD tray and secure it using four flat screws. -
Page 41: Rack Mounting
Mounting Ears x 2 Screw Sack x 1 2.2.1 Installing the Server in a Rack Follow these instructions to mount the FT72-B7015-LE into an industry standard 19” rack. Before mounting FT72-B7015-LE in a rack, ensure that all internal components have been installed and that the unit has been fully tested. -
Page 42: Installing The Inner Rails To The Chassis
Screw the mounting ear to each side of FT72 as shown using 3 screws from the supplied screws kit. Push the latch key and draw out the inner rails from sliding rails. Secure inner rails to both sides of the chassis, be sure the five mounting holes are correctly matched. http://www.tyan.com... -
Page 43: Installing The Outer Rails To The Rack
4 M5 x 10 screws with washer for each side. 2.2.4 Rack mounting the Server 1. Draw out the middle rail till the latch position. 2. Lift the chassis and then insert the inner slide rails into the middle rails. http://www.tyan.com... - Page 44 3. Push the chassis in and pull the latch key (A). Then push the whole system into the rack (B). 4. Secure the mounting ears of chassis to the rack with 2 M5 x 13 screws. http://www.tyan.com...
-
Page 45: Chapter 3: Replacing Pre-Installed Components
Components Introduction This chapter explains how to replace the pre-installed components, including the Motherboard, M1008 front panel board, M7015 power distribution board, M7015 power backplane, system fan, power cage etc. Disassembly Flowchart The following flowchart outlines the disassembly procedure. http://www.tyan.com... -
Page 46: Removing The Cover
Removing the Cover Before replacing any parts you must remove the chassis cover. Follow Chapter 2.1.1 to remove the cover of FT72-B7015-LE. Replacing the Power Supply 3.4.1 Replace the power supply To replace the power supply follow these instructions. Press the tab as shown in the diagram and pull out the power. -
Page 47: Replacing M7015 Power Distribution Board
3.4.2 Replacing M7015 Power Distribution Board 1. Remove the 2 screws securing M7015-PDB to the bracket. 2. Renew the M7015-PDB and fix it to the chassis following the step in reverse. http://www.tyan.com... -
Page 48: M7015 Power Distribution Board Features
3.4.3 M7015 Power Distribution Board Features 17 Power Connectors (2x4 pin) for PCI-E add on card & System fan Power Connector (Connect to M7015-PBP PWR backplane) http://www.tyan.com... -
Page 49: Replace The M7015 Power Backplane
After pulling out both the power supplies and the M7015-PDB, then we can lift out the M7015-PBP bracket. 2. Remove the 4 screws securing M7015-PBP to the bracket. 3. Renew the M7015-PBP and fix it to the chassis following the steps in reverse. http://www.tyan.com... -
Page 50: M7015 Power Backplane Features
3.4.5 M7015 power backplane Features M7015-PBP Power backplane support FT72-B7015-LE with EMERSON DC1200-3 power supply. On board PWR Connector * 3 (Vertical, connect to PWR supply) PWR Connector (Right angle, connect to MB) PWR Connector (Vertical, connect to M7015-PDB PWR distribution board) http://www.tyan.com... -
Page 51: Replacing M7015 I/O Board
After remove power supplies and M7015 PBP, you can replace the M7015 I/O board following these instructions. Remove the four screws of power cage from the chassis. Lift the power cage out of the chassis and locate the M7015 I/O board. http://www.tyan.com... - Page 52 Unscrew M7015 I/O board with its bracket and carefully pull it up. Renew the M7015 I/O board and fix it to the chassis following the step in reverse. http://www.tyan.com...
-
Page 53: Replacing The Led Control Board
Follow these instructions to replace the M1008 LED control board. Unplug the cables from the connectors on M1008 and main board. A: From M1008 B: From S7015 Remove the three screws securing the LED control board unit to the chassis. http://www.tyan.com... -
Page 54: M1008 Led Control Board Features
3. Renew the board and place it back to the chassis following the above procedures in reverse. 3.6.1 M1008 LED Control Board Features http://www.tyan.com... -
Page 55: M1008 Led Control Board Connector Pin Definition
M1008 LED Control Board Connector Pin Definition J1: USB Header Definition Definition USB1- USB2- USB1+ USB2+ J3: SSI Definition Definition PW_LED+ ID_LED+ PW_LED- ID_LED- HD/LAN3 LED+ SYS_FAULT1- HD/LAN3 LED- SYS_FAULT2- PWR_SW+ LAN1_LED+ PWR_SW- LAN1_LED- RESET+ ICH_SMBDAT RESET- ICH_SMBCLK ID_SW+ INTRU# TEMP_SENSER LAN2_LED+ EXT_INT LAN2_LED- http://www.tyan.com... -
Page 56: Replacing The System Fan
Remove the three screws securing the fan holder into the chassis and lift the fan holder out. Remove the four screws securing the fan to the fan holder. Renew the fan and reinsert the fan holder into the chassis and fix it with four screws. http://www.tyan.com... -
Page 57: Replacing The Rubber Screws
1. Insert the rubber screw into the fan holder. 2. Pull the rubber screw through the fan holder and make its projecting part stuck at the fan holder. 3. Insert the four rubber screws into the fan hole. http://www.tyan.com... - Page 58 NOTE：When use pliers or relatively sharp tool, preferable to wrap sharp pliers with some tape or paper tape or the like, to prevent damage to the rubber. As the rubber screw is a one-time product, the assembly can not be repetitive, it would be best not have removed after replacement. http://www.tyan.com...
- Page 59 8. Secure the two screws on the fan holder. ： NOTE As replacing fan mount is to increase the 2.5 'HDD performance, only if clients have no such demand or only request install 3.5' HDD, the replacement need not be carry out. http://www.tyan.com...
- Page 60 Remove the 15 screws securing the motherboard to the chassis. Carefully lift the motherboard from the chassis as S7015 is too large to lift straight out .Lift the front edge of the board to an angle of about 45 then slides the whole board out. http://www.tyan.com...
-
Page 61: Appendix I: Redundant Power Behavior
Buzzer beep(if installed) NOTE: When the input voltage is between 100V~127V. FT72-B7015-LE requires the current input at 12.0 Amp MAX, or when the input voltage is between 200V~240V, it requires current input at 7.0 Amp MAX. - Page 62 http://www.tyan.com...
-
Page 63: Appendix Ii: Cable Connection Tables
3. SATA & SATA PWR Cable HDD device to S7015 MB HDD device Connect to S7015 MB → SATA cable 1 for HDD1 CN10 → SATA cable 2 for HDD2 CN11 SATA PWR cable for → HDD1 & HDD2 http://www.tyan.com... - Page 64 PW5 or PW6 GPU card 3 → PW7 or PW8 GPU card 4 → PW9 or PW10 GPU card 5 → PW11 or PW12 GPU card 6 → PW13 or PW14 GPU card 7 → PW15 or PW16 GPU card 8 http://www.tyan.com...
-
Page 65: Appendix Iii: Fru Parts Table
Appendix III: FRU Parts Table FT72-B7015-LE FRU Parts Model Item Part Number Picture Quantity Description Number Power CPSU-0420 471100600034 1200W,Power Supply, EMERSON DS1200-3 Supply CFAN-0350 336252012362 120X120X38MM FAN;12V,9GV1212P1J031 CABLE ASSY;PCI-E CARD PWR CABLE,2*3P CCBL-146H 422786600003 /2*3P CABLE ASSY;PCI-E CARD PWR CABLE,2*4P... - Page 66 NOTE: The table is subject to change without notice. Please visit our web site at http://www.tyan.com for latest update. http://www.tyan.com...
-
Page 67: Appendix Iv: Technical Support
(which can have expensive consequences). If these options are not available for you then TYAN Computer Corporation can help. Besides designing innovative and quality products for over a decade, TYAN has continuously offered customers service beyond their expectations. - Page 68 Return Merchandise Authorization (RMA) number. The RMA number should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. TYAN will pay to have the board shipped back to you ®...