Panasonic PT-AE2000E Spec File
Full high-definition home cinema projector
Hide thumbs
Also See for PT-AE2000E:
- Operating instructions manual (58 pages) ,
- Brochure & specs (4 pages) ,
- Service manual (81 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Table of Contents
Related Manuals for Panasonic PT-AE2000E
Summary of Contents for Panasonic PT-AE2000E
- Page 1 PT-AE2000 P ro d u c t N u m b e r : Full High-Definition Home Cinema Projector P ro d u c t N a m e : As of September 2007. Appearance and specifications are subject to change without notice.
-
Page 2: Specifications
Full High-Definition Home Cinema Projector Specifications Main Unit Power supply: Power consumption: LCD* panel: Panel size: Display method: Drive method: Pixels: Lamp* Lens: Screen size: Throw distance: Colours: Brightness* Centre-to-corner uniformity ratio* Contrast* Resolution: Scanning frequency: RGB: S-Video/Video: Optical axis shift*... - Page 3 Optional Accessories *1: The projector uses a type of liquid crystal panel that typically consists of millions of pixels. This panel is built with very high-precision tech- nology to provide the finest possible image. Occasionally, a few pixels may remain turned on (bright) or turned off (dark). Please note that this is an intrinsic characteristic of the manufacturing technology that affects all products using LCD technology.
- Page 4 Full High-Definition Home Cinema Projector Dimensions (18-1/8˝) Terminals COMPUTER IN connector pin assignment D-sub HD 15-pin, female As of September 2007 1 HDMI 1 input 2 HDMI 2 input 3 HDMI 3 input 4 Computer input 5 Component (YP 6 Component (YP...
- Page 5 Full High Definition Home Cinema Projector Standard setting-up positions Upper edge of projected image Projected image Lower edge of projected image Projected image Projection distance (screen aspect ratio 16:9) Projection size (16:9) Projection distance (L) Diagonal length Min (Wide) Max (Telephoto) 1.01 m...
- Page 6 Optical axis shift function allows to shift the position of a projected image as shown below. 0.4H Installable angle Install the projector at an angle within the range shown below. • Vertical direction The projector may be installed at a vertical angle of ±30°.
-
Page 7: Computer Data Compatibility
This projector accepts up to 70 kHz horizontal scanning frequency and 150 MHz dot clock. NOTE: The display resolution of this projector is 1920 x 1080 pixels. If the display resolution indicated in the above data does not match this resolution, the input signal will be converted to 1920 x 1080 pixels. - Page 8 Add parameters according to the details of control. Start (1 byte) CAUTIION When sending multiple commands, be sure to send the next command after receiving a response from the projector. Cable specifications As of September 2007 Description...
-
Page 9: Control Commands
Full High-Definition Home Cinema Projector Control commands Command: <Parameter> Function Power on (standby mode on) Power off (standby mode off) Input signal selection IIS:<input signal > Freeze OFZ:<off_on> Enter VPM:<picture mode > Picture mode <NOR> Normal <DYN> Dynamic <CN1> Cinema 1 <CN2>... -
Page 10: Parameter Format
<off_on> <input signal> <power condition> <off_timer> <x> NOTE: If a wrong command is received, the projector will send an ER401 command to the computer. Command example To set the volume to +30, send the command as shown below. Start Command NOTE: When sending commands without parameters, a colon (:) is not necessary. - Page 11 Make sure there is an unobstructed space of 100 mm (3-15/16˝) or more around the projector’s air intake openings. If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust openings are not blocked.