Panasonic KX-TGA523 Operating Instructions Manual page 3

Getting Started
1-F Battery Charge
Place the handset on the charger and charge
for 6 hours before initial use.
•The unit beeps once, the CHARGE indicator
lights and "Charging" is displayed.
•When the battery is fully charged, "Charge
completed" is displayed if there are no
new calls in the Caller List.
CHARGE Indicator
•Recharge the battery when:
– "Recharge battery" is displayed on the handset,
– " " flashes, or
– the handset beeps intermittently while it is in use.
•If the battery has been discharged, the handset will display "Charge
for 6 HRS" and " " when you place the handset on the
charger. The handset will not work unless the battery is charged.
Continue charging.
1-G Handset Registration
This handset must be registered to a KX-TG5200/KX-TG5202/
KX-TG5210/KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391 base
unit.
The handset will be assigned an extension number at registration.
The KX-TGA523 will not work without one of the following Panasonic
cordless phone systems: KX-TG5200/KX-TG5202/KX-TG5210/
KX-TG5212/KX-TG5230/KX-TG5240/KX-FPG391.
CHARGE Indicator
*LOCATOR Button
•Base unit model shown here is KX-TG5240.
*
The location of LOCATOR button varies by base unit model.
KX-TG5200/KX-TG5202: LOCATOR [
KX-TG5210/KX-TG5212: LOCATOR/INTERCOM [
[ ] or [ ]
KX-TG5230/KX-TG5240/KX-FPG391: [LOCATOR/INTERCOM/TRANSFER]
1-H Setting Time
The charger unit has a 12-hour clock (monthly accuracy
seconds). After the AC adaptor is connected, "
display. Follow the steps to set the clock.
[+, -, TUNE/CLOCK]
[-]
Press LOCATOR
on base unit
for 3 sec.
Then press OK
BACK
OK OK
Soft Key ( )
OK
], [ ], [ ], [ ] or [
], [ ], [
±
30
" flashes on the
[TIME SET]
[OFF]
For assistance, please call: 1-800-211-PANA(7262)
Battery information
After your Panasonic battery is fully charged, you can expect the
following performance:
Operation
While in use (TALK)
While not in use (Standby)
While using Clarity Booster feature
•Clean the charge contacts of the handset and the charger with a
soft, dry cloth once a month. Clean more often if the unit is
subject to grease, dust or high humidity. Otherwise the battery
may not charge properly.
A nickel metal hydride battery that is recyclable
powers the product you have purchased. Please call
1-800-8-BATTERY for information on how to recycle
this battery.
Only one handset can be registered at a time.
Make sure the base unit and the other handsets are not being used.
Have both the handset and base unit nearby during registration.
The handset display shows the
instructions as shown on the right.
1
Base unit: Press and hold the
*LOCATOR button for 3 seconds.
• The CHARGE indicator flashes. After the CHARGE indicator starts
flashing, the rest of the procedure must be completed within 1 minute.
•On the KX-FPG391, "HS REGISTRATION" is displayed.
2
Handset:
#Press the soft key (
$Wait until a long beep sounds and the
display shows the new extension number.
•Registration is complete.
•The registered number "[1]" to "[4]" is shown on the top right of
the display.
•You can stop registration by pressing [OFF] on the handset and
pressing the *LOCATOR button on the base unit.
•To cancel the handset's registration, please see the base unit
]
Operating Instructions.
],
•If you try to register this handset to the KX-TG6500 base unit,
"Wrong handset Refer to manual" is displayed. The base
units for this handset are mentioned above.
1
Press [TIME SET].
2
Adjust the time by pressing
[+, TUNE/CLOCK] or [–, TUNE/CLOCK].
• Pressing [+] or [–] increases or
decreases the time in one-minute units.
• Pressing and holding [+] or [–]
increases or decreases the time faster.
3
Press [TIME SET] to set the clock.
• The time stops flashing.
•You can exit time setting mode any time by pressing [OFF].
•If a power failure occurs, the display will show "
minutes, then it will become blank. After power returns, "
be displayed. The clock memory will be lost. Set the clock. The radio
alarm and buzzer alarm memory will be retained for about 10
minutes during a power failure (4-A, 4-B).
Section 1
Operating time
Up to 5 hours
Up to 11 days
Up to 3 hours
Press LOCATOR
on base unit
for 3 sec.
Then press OK
Ex. Extension number 2
).
OK
SP
Handset [2]
Registered
Ex. 3:30PM is set.
" for about 10
O K
[ ]
PRIVACY 2
" will