Multi-Brand Remote Control - JVC HR-VP693U Instructions Manual

– Other Functions –
Child Lock
You can disable the VCR operations. While the VCR is turned on,
press and hold POWER on the Remote for more than 10 seconds.
The VCR turns off, "CL" appears for about 5 seconds on the
display panel.
To release the child lock, press and hold POWER on the Remote
until the VCR turns on.
NOTES:
● Pressing TIMER during timer recording, unplugging the AC
power cord or a power outage also releases the child lock.
● When the child lock function is in use, keep the Remote out of
the children's reach.
● Timer recording programs will be performed even if the child
lock function activated.

Multi-Brand Remote Control

This Remote can control some functions of remote controllable
TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers
listed below. Without setting, you can control a JVC TV.
NOTES:
● Some unit's brands have more than one code. If the unit does
not function with a specified code, try other codes.
● Depending on the type of unit, some or all functions cannot be
operated using this Remote.
● It's not possible to operate a unit not equipped with a remote
sensor.
● It's not possible to set the Remote for both your cable box and a
DBS receiver at the same time.
● Once you have set the Remote to operate the unit, you do not
have to set it until you replace the batteries from the Remote.
TV Brand Setting
A
Turn on TV
Turn on the TV using the Power button on the TV or its Remote.
B
Set TV brand code
A Press and hold TV.
B Press MBR SET.
C Press the Number keys to enter your TV's brand code.
D Press OK, and release TV. The TV should turn off.
C
Operate TV
While holding down TV, press one of the following buttons:
POWER, TV/VCR, TV CH+/–,
the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
TV BRAND CODE
JVC 01, 03
HITACHI 10
MAGNAVOX 02
MITSUBISHI 03
PANASONIC 04, 11
RCA 05
SHARP 06
Cable Box or DBS Receiver Brand Setting
A
Turn on cable box or DBS receiver
Turn on the cable box or DBS receiver using the Power button on
the unit or its Remote.
B
Enter brand code
A Press and hold CABLE/DBS.
B Press MBR SET.
C Press the Number keys to enter your cable box's (or DBS
receiver's) brand code.
D Press OK, and release CABLE/DBS.
^
(TV Muting), TV VOL+/–, and
TV BRAND CODE
SONY 07
SAMSUNG 12
SANYO 13
SEARS 13
TOSHIBA 08
ZENITH 09
C
Operate cable box or DBS receiver
While holding down CABLE/DBS, press one of the following
buttons: POWER, TV CH+/–, and the Number keys.
● For some brands, you must press ENTER after having pressed the
Number keys to enter a channel number.
● To change the cable box's (or DBS receiver's) channels, press TV
CH+/– or the Number keys. (The CH+/– button can be used to
change the VCR's channels only.)
CABLE BOX BRAND
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
EASTERN
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REGENCY
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
DBS RECEIVER BRAND
JVC (DISH Network)
ECHOSTAR (DISH Network)
PRIMESTAR
SONY (DSS)
RCA (DSS)
Changing Remote Control Code
This Remote is capable of transmitting two control codes; one set
to respond to A code control signals and another set to respond to
B code control signals. This Remote control is preset to send A
code signals because your VCR is initially set to respond to A
code signals. You can easily modify your VCR and the Remote to
respond to B code signals. When using two JVC VCRs, set two
VCRs and their Remotes to different codes, so that you can
operate these VCRs separately.
A
Set remote control code for Remote
A Press and hold A/B.
B Press the Number key "2".
C Press OK, and release A/B.
● The Remote now can transmit B code control signals.
B
Check remote control code for VCR
Press and hold 4 on the VCR for more than 5 seconds while the
VCR is turned off. The code currently set appears on the display
panel.
C
Change code for VCR
Press any key on the Remote. The VCR now responds to B code
control signals.
● To set the Remote and the VCR back to A code control signals,
repeat the same procedure as shown above except pressing the
Number key "1" in step B of 1 1 1 1 .
CODE
01, 05, 17
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
02
01, 17
19
15, 16, 17, 21, 25
15
01, 04, 06, 11, 12, 15, 28
10, 18, 19, 23
15
01, 04, 06, 11, 12, 15, 28
02
07
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 19, 23
19
01, 16, 17
05, 16, 24
02
07
05, 16, 17, 24, 25
13, 14
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
16, 17, 25
03, 09, 22
03, 09, 22
CODE
51
51
50
41
40